SCOTT GENIUS USER MANUAL All rights reserved © 2017 SCOTT Sports SA Distribution: SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium v6.3/040717 WWW.SCOTT-SPORTS.COM SCOTT Sports SA Route du Crochet 17, CH–1762 Givisiez Phone: +41 26 460 16 16 | Fax: +41 26 460 16 00 Email: scottsupport@scott-sports.com W W W. S C O T T- S P O R T S .
••CONTENTS Genius Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 Geometry/Technical Data Genius 700 . . . . . . . . . . . . . . . . . . . . . . 05 Geometry/Technical Data Genius 900 / 700 Plus . . . . . . . . . . . . . . . 06 WWW.SCOTT-SPORTS.COM TC Shock Technology/Twinloc Levers . . . . . . . . . . . . . . . . . . . . . . 07 Assembly of the Remote Cable . . . . . . . . . .
••GENIUS CONCEPT ••GEOMETRY/TECHNICAL DATA GENIUS 700 The new Genius is the result of 2 years of research and development for one of the lightest trail/marathon bike frame set available on the market, hitting the scale at below 2300g (5lbs) including the frame, FOX Nude /CTD shock and the unique TWINLOC remote control. Travel 150/100/0mm Suspension Ratio 2.
••GEOMETRY/TECHNICAL DATA GENIUS 900 / 700 PLUS Travel GENIUS 700 PLUS HEAD TUBE ANGLE HEAD TUBE LENGTH TOP TUBE C HORIZONTAL STANDOVER D HEIGHT A 130/90/0mm B Suspension Ratio 2.60 Piston stroke 50mm Shock length (Eye to Eye) 190mm Hardware Mainframe 22.2mm x 8mm Hardware Swingarm 22.2mm x 8mm Seatpost diameter 31.6mm Headset semi integr. for tapered 1 1/8-1.5 (44/54.9mm Inner diameter of frame) or with 1 1/8 straight (44.
Therefore SCOTT offers 2 different TWINLOC levers with following fork/rear shock combinations: For the assembly of the remote control of the front fork lock-out 2 different cable rolls which are changeable are existing. -- FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTT Article number: 230097) The different roll for the pull of the fork remote cable can be changed within few minutes to adapt the lever to your fork model/brand.
••ASSEMBLY OF THE REMOTE CABLE ••FOX NUDE SHOCK AND TWINLOC REMOTE CONTROL LEVER •• In the drawing of the shock and remote lever, shown below, you will see the parts indicated with numbers which will be used in the manual for the adjustment and setup. IMPORTANT! Please make sure the lockout of SRAM/RockShox or FOX fork is activated after transport correctly. Therefore please compress fork 5-10 times before following the manual on remote cable installation and adjustment.
••BASIC SET-UP OF THE TWINLOC REMOTE CONTROL OF FOX 3. tighten the cable and fix the cablefixing screw (S7) by turning it clockwise with a 2mm allen key and a max. tightening torque of 1.6Nm. NUDE SHOCK To ensure perfect function of the FOX Nude shock it is very important to follow the steps shown below exactly. On Genius Carbon frames you will find an internal cable routing.
••BASIC SET-UP OF THE TWINLOC REMOTE CONTROL OF FOX CTD SHOCK ••SET-UP GENIUS WITH FOX NUDE OR FOX CTD SHOCK The Set-Up of the FOX Nude or FOX CTD Shock can be easy done within a few minutes. The assembly of the remote cable and the setup of the FOX CTD rear shock is very similar to the abovementioned assembly and setup of the FOX Nude. For more details on the FOX CTD please follow the details shown in the manuals of FOX attached to this bike.
••SAG Please refer to the following instruction: The SAG should be 14mm (700) respectively 12.5mm (900 / 700 Plus) on the shock piston. To check the adjustment, please follow as shown below: 1. sit on the bike, put your feet on the pedal 2. put your feet back on the ground and stand over the bike without bouncing the bike during this action 3. check if the o-ring (S9) on the shock piston (S8) has a distance of 14/12.5mm to the main dust wiper/seal between shock housing and piston.
••SET-UP OF OTHER SHOCK MODELS It is also possible to use forks with a standard 1 1/8” steerer tube when using a reducer headset such as e.g. SCOTT strongly recommends using only the FOX Nude (FOX CTD shock) with the Genius bike, as we designed both parts for a perfect matching combination with a linear suspension rate. Ritchey WCS Carbon Zero Tapered PF 50-61mm 18mm UD for 1 1/18" fork PRD 14860 Also on those shock models the SAG should be 14/12.5mm.
••ADJUSTABLE BB HEIGHT ••FRONT DERAILLEUR (FD) MOUNTING DETAILS On Genius bikes equipped with the FOX Nude or the FOX CTD shock you can adjust the BB height above ground in 2 positions by flipping a geometry chip located on the linkage bar shock mount.
••CHAINGUIDE Details for the assembly on the alloy frames of Genius: The Carbon as well as the alloy frames of Genius can be fitted with ISCG chainguide systems. A set of all spare parts for this action can be ordered via the SCOTT distribution with: 229730 ISCG adaptor Genius 2013 Details for the assembly on the carbon frames of Genius: The adaptor must be used in order to assemble the chainblocker on the ISCG05 chainguide system.
Please note that the inner cables need to cross each other 1 time on the inside of the downtube before you pull them out through the cable slot on the lower downside of the downtube.
In addition to the derailleur cables and the brake hose you also will see a possibility for an integrated cable routing of the seatpost remote on the carbon version of Genius. Please make sure to respect the 40mm distance between the cables and the BB (bottom bracket) housing to avoid “ghost-shifting” and/or damages on the shift cables and brake hose.
••REPLACEABLE DROPOUT For 185mm rotor diameter you will need 2 red anodized spacers that can be ordered via the SCOTT distribution with: On Genius bikes of model year 2013 you can replace the rear derailleur hanger. Depending on the different models you’ll find following options: 219568 Brake Mount Adapt.Spacers 4mm f/185mm 1.
••GUARANTEE ON SCOTT BIKES improper or incorrectly performed maintenance or repairs performed by someone other than an authorized SCOTT dealer, use of parts or devices not consistent with the Product, and alteration of the Product. •• WARNING! SCOTT Sports SA is not responsible or liable for any injury caused by any missing compliance with these instructions, particularly but not limited to misuse, incorrect maintenance, incorrect set-up and handling, neglect or abuse.