ASTRA 1000RS AUTOMATIC/MANUAL TRANSMISSION REMOTE START SYSTEM PRODUCT MANUAL
Limited Lifetime Warranty This vehicle remote start system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Table of Contents 1. 2. 11. 12. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Your System The Astra 1000RS is a state-of-the-art remote starting system with an integrated 2-way paging feature. With proper installation, this system will provide superior protection and performance for many years to come. The Astra 1000RS built-in remote start feature is designed to offer maximum convenience by remote starting your vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined time to provide a comfortable environment once you enter your vehicle.
Remote Transmitters Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The Astra 1000RS is supplied with one 5-button Remote Transmitter used to control system operations. Button 1 Locks the doors and when held for 2 seconds, activates the system’s Car locator feature. Button 2 Unlocks the doors. Button 3 Activates the Auxiliary 1 output. Type of output can be programmed for customization. Button 4 Activates the Remote Start feature. Button 5 is the Page Shift button.
3. Press Button 1 on the first transmitter. · The parking lights will flash once. 4. Press Button 1 on the first transmitter again. · The parking lights will flash twice to indicate it has learned the code. 5. Repeat steps 3 and 4 for each transmitter (up to 4). 6. Turn off the ignition key. · The parking lights will flash 3 times. To program 2-way LCD transmitter(s): 1. Turn the ignition key On, Off, On, Off, On, Off and back On· .The parking lights will flash 4 times. 2.
Optional 2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 The Astra 1000RS Plus is compatible with the optional 2-way LCD remote transmitter, offering increased range and confirmation of any activated features. Button 1 Locks and Unlocks the system and when held for 2 seconds, activates the system’s Car locator feature. ·Also locks/unlocks the doors when the system is in Valet Mode. Button 2 Activates the Remote Start feature.
LCD Transmitter Battery Replacement Your Galaxy LCD Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery may last up to six months before it needs replacement. When the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery voltage drops below minimum.
Visual Indications · The LCD panel will play a tone if the sounds are enabled or "off" will be displayed if the chirps are disabled. System Armed indicates the doors are locked and the Starter Kill is active. Door Open N/A System Disarmed indicates the doors are unlocked and the Starter Kill is off. Shock Sensor N/A. Engine Run indicates the engine is running. Warn Away N/A Lock indicates the doors Valet Mode indicates the system has been placed are locked and the system is in valet mode.
System Operation Remote Locking To Lock the doors: 1. Turn off the ignition. 2. Press Button 1. · The doors will lock. · The parking lights will flash once. · The LED will turn on red, to indicate the doors are locked. 3. 10 seconds after Locking: · The LED will start blinking as a theft deterrent and the Starter Kill will activate. Remote Unlocking To Unlock the doors: Press Button 1 on 2-way transmitter or button 2 on 1-way transmitter. · The doors will unlock. · The parking lights will flash twice.
Remote Start Features Manual/Automatic Transmission Mode Astara 1000RS is designed to be used in vehicles with automatic or manual transmissions. The unit must be set to automatic or manual mode if used in automatic or manual transmissions vehicles. A wire loop extended out of the unit box determines the mode. Cut the loop to put the unit in the automatic transmission mode. Uncut loop keeps the unit in a manual transmission mode.
Shut Down When the the Remote Start feature is active, any of the following actions will shutdown the engine: 1. Pressing Button 4 on 1-Way or Button 2 on 2-Way Transmitter. · After the engine shuts down the doors will lock (programmable) 2. Pressing the Brake Pedal. 3. Opening the Hood. 4. Remote Start Time-Out (completion of the timed run cycle). Quick Stop (Automatic Transmission Only) The Quick Stop Feature allows you to exit the vehicle while keeping the engine running for quick stops.
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off.
System Installation 1. 2. Thoroughly read and become familiar with the installation instructions before beginning the installation. Review system contents: Main Unit One 1-way and one 2-way Transmitters Harnesses • 16-Pin main harness • 3-Pin door lock harness • 2-Pin LED harness • 2-Pin Override Switch harness 3. Verify vehicle is equipped with electronic fuel injection, and starts/idles normally before installation. 4.
System Wiring 5-Pin Harness Pin 1 Pin 2 Pin 3 pin 4 pin 5 ORANGE WIRE: Accessory Output for heater/air conditioner(negative) to activate external relay YELLOW WIRE: Ignition 1 output (negative) to activate external relay. VIOLET WIRE: Starter Output (negative) to activate external relay BROWN WIRE: Ignition 2 output (negative) to activate external relay. RED WIRE: +12V Power to external relays. 16-Pin Main Harness Pin 1 BLUE WIRE - 1 pulse remote start (-) input.
independent left and right parking light circuits, diodes must be installed to keep the circuits separate. NOTE: Do not connect the WHITE wire to the vehicle’s headlight circuit. Pin 16 RED WIRE: Module Power Input (+). Connect to a constant source of +12V. 2-Pin Blue Connector: Valet switch port. Mount switch where it is accessible from the driver’s position. 2-Pin Red Connector: LED port. Mount LED where it may be easily seen from either side of the vehicle.
Jumper Settings Jumper Selection Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity output as described below, then reassembly the main unit case. Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay.
System Programming Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The parking lights will flash three (3) times indicating you have entered Programming. 3. Press the valet switch the number times equal to the System Parameter you want to change. · The parking lights will flash each time the valet switch is pressed. 4.
Momentary operation provides an output for as long as the transmitter button is pressed. Timed operation provides an output that turns on for 10 seconds each time the transmitter button is pressed. If the button is pressed again during the 10 seconds, the output will turn off. Latched operation provides an output that turns on when the transmitter button is pressed and remains on until the transmitter button is pressed again. 6. Unlock with Aux 1.
Branch Feature 1. Ignition Door Locking 2. Ignition Door Unlocking 3. Door Unlock Pulse 4. Door Lock Pulse Length 5. Aux 1 Mode 6. Unlock with Aux 1 7. Start in Valet Mode 8. Lock after Start 9. Lock after Shutdown 10. Engine Run Time 11. Automatic Start Mode 12. Tachless Sense Crank Time 13. Engine Type 14. Ignition 2 Output Program 15. Turbo/Manual Transmission Start 16. Unlock Before Start 17. Rearm/Horn Output Mode 18.
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages.
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
Wiring Diagram Green - Lock Out (-) 500ma Red - +12V Relay PWR Blue - Unlock Out (-) 500ma Antenna Orange - Accessory Output Yellow - Ignition 1 Output Violet - Starter Output Brown - Ignition 2 Output Red - +12V to Relays Valet LED Door Lock Relay Block Must Cut the loop for Automatic Tansmission mode Blue - Remote Start Input (-) Black/Gray - Tach Input White/Red - Parking Brake Input (-) Green - Negative Door Input (-) Violet - Positive Door Input (+) Yellow - +12V Ignition Input (+) White/Black -