User guide

ManualsBrandsSDC ManualsFor Home350 NARROW LIINE EMLOCK

P:\INSTALLATION INST\Electromagnetic Locks\INST-350.vsd REV - 02-12 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

INSTALLATION INSTRUCTIONS

350 NARROW LIINE EMLOCK

Electrical Instructions:

Use properly fused U. L. Listed Power Supply

Do not install a diode in parallel with any magnetic lock. A diode

will cause a delay when releasing the door and residual magnetism

to occur.

Access controls and/or release contacts must be located in series

with the positive (+) power lead of the EmLock.

Any low voltage condition will cause erratic operation of the

optional board sensor.

Although SDC recommends the use of a Regulated DC power supply, a

transformer with an adjacent mounted full wave bridge rectifier

may be used. A significant voltage drop will occur when using a full wave

bridge rectifier.

Electrical Specifications:

Dual Voltage 12 or 24VDC

Power Consumption 540mA@12VDC

300mA@24VDC

DS Door Status Sensor SPDT, 250mA@30VDC

LS Lock Status Sensor SPDT, 2A@30VDC

Outswing

Quick Mount

Interlocking

Mounting Assembly

Mounting Screws

Armature

Interlocking

Mounting Plate

Frame

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

Retrofits Discontinued Locknetics 350+

Provides Superior Architectural Appearance

Supplied Mounting Hardware

PATENT NO. 5,376.910

Summary of content (6 pages)

PAGE 1
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS 350 NARROW LIINE EMLOCK Retrofits Discontinued Locknetics 350+ Provides Superior Architectural Appearance Interlocking Mounting Plate Quick Mount Interlocking Mounting Assembly Frame Mounting Screws Armature Outswing Electrical Instructions: Electrical Specifications: Use properly fused U. L.
PAGE 2
1. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb side of the frame. 2. Mark and drill holes as indicated by the template. STEPS 1 & 2 3. Mount armature to door. STEP 3 STEEL WASHER 2X 5/16-18 SOC HD SCREW WITH 3/16 (5MM) ALLEN HEX ARMATURE REINFORCEMENT TUBE 1-3/4“ HOLLOW METAL DOOR 5/8“ DRILL 1/2” DRILL SEXNUT RUBBER WASHER HOLLOW METAL DOOR From Sexnut side of door, drill exactly 1/2” hole thru one metal thickness only.
PAGE 3
5. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the door. Tap with a soft hammer to ensure proper alignment and engagement. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing STEP 5 6.
PAGE 4
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS 352 NARROW LIINE EMLOCK Interlocking Mounting Plate Quick Mount Interlocking Mounting Assembly Frame Mounting Screws Armature Outswing Electrical Instructions: Electrical Specifications: Use properly fused U. L. Listed Power Supply Dual Voltage Do not install a diode in parallel with any magnetic lock.
PAGE 5
1. Fold template as indicated on dotted line. For double doors center template against the doors and header. 2. Mark and drill holes as indicated by the template. STEPS 1 & 2 3. Mount armatures to doors. STEEL WASHER 2X STEP 3 (2X) 5/16-18 SOC HD SCREW WITH 3/16 (5MM) ALLEN HEX ARMATURE REINFORCEMENT TUBE 1-3/4“ HOLLOW METAL DOOR 5/8“ DRILL 1/2” DRILL SEXNUT RUBBER WASHER HOLLOW METAL DOOR From Sexnut side of door, drill exactly 1/2” hole thru one metal thickness only.
PAGE 6
5. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the door. Tap with a soft hammer to ensure proper alignment and engagement. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing STEP 5 6.