iBT210 Bluetooth Wireless Dual Alarm Clock instruction manual Questions? Contact Customer Service at 1-800-288-2792
iBT210 Introduction Thank you for purchasing the iHome iBT210. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod or other Bluetooth audio device. This instruction booklet explains the basic operation and care of the unit. Please read it carefully and keep for future reference. Maintenance • Place the unit on a level surface away from sources of direct sunlight or excessive heat.
iBT210 Table of Contents What’s Included ...............................................................................................................3 Meet Your iBT210 ............................................................................................................4 The Display/Setting Up the Unit ..........................................................................................5 Replacing and Installing Clock Backup Batteries .........................................................
iBT210 Included • iBT210 Alarm Clock • 100V-240V universal AC adaptor • 2 AA batteries power adaptor iBT210 alarm clock 3 2 AA batteries
iBT210 Meet Your iBT210 Top Presets Button Mode Button Alarm 1 Button Alarm 2 Button Power/ Alarm Reset Button Volume Down/ Volume Up Buttons Answer Call/ Plus Settings Button Snooze/Display Dimmer Button End Call/ Minus Settings Button Microphone Play/Pause/Pairing Button Bottom Back Aux-in Jack USB Charging Port AA AA Sleep/Clock Adjust Button Backup Battery Compartment 4 FM Antenna DC Jack
Using the The Display Bluetooth Indicator iBT210 Alarm 1 & Alarm 2 Indicators Battery Low Indicator Sleep Indicator Time Display PM/AM Indicators FM Radio Indicator Wake to Indicator AUX indicator Alarm Time/Date/Radio Frequency Wake to source: outlet BT (Bluetooth), FM Radio, Buzzer Mode: BT (Bluetooth), FM Radio, Aux (MP3) Setting Up the Unit T ESER RESET T SET TEST Connect the included AC adaptor to the DC jack located on the back of the unit and connect the other end to a working wall o
Using the iBT210 Replacing and Installing Clock Backup Batteries Note: 2 AA batteries are included with the unit. Install them before using the unit. This model is equipped with a battery backup circuit that will maintain the time and alarm time settings in the event of a temporary power interruption (the display is NOT lit). The battery backup circuit will also operate the buzzer alarm to wake you up at the selected wake up time even if the power is out.
Using the Setting the Clock iBT210 1. Press and hold the Sleep/Clock Adjust Button located on the back of the unit for 2 seconds until the clock display flashes and a beep sounds. 2. Press the or Buttons to adjust the clock to the current time (hold for rapid setting). Make sure you set the correct AM/PM time. The AM and PM indicators appear to the left of the display. 3. Press the Sleep/Clock Adjust Button to confirm the time. The year will flash on the display. 4.
Setting and Using the Alarms (Continued) Using the iBT210 1. Press and hold the Alarm Button for 2 seconds until the alarm time display and alarm icon flash. A beep sounds. 2. Press the or Buttons to adjust the alarm time to the desired time (hold for rapid setting). Make sure you set the correct AM/PM alarm time. The AM and PM indicators appear to the right of the alarm time display. 3. Press the Alarm Button to confirm the alarm time setting. The wake-to source will flash. 4.
Using the Snooze/Display Dimmer Button iBT210 1. The default snooze time is 9 minutes. To adjust Snooze duration, press and hold the Snooze/Display Dimmer Button during normal operation (when no alarm is sounding). 2. Press the or Buttons to select the desired snooze time (between 01 and 29 minutes). 3. Press and release the Snooze/Display Dimmer Button to confirm Snooze setting. 2 beeps will sound. 4.
Using the Setting and Using FM Presets iBT210 The unit allows you to store up to 6 FM radio station presets 1. Press and release the Mode Button as needed until the FM indicator icon appears on the display. 2. Press and release the Presets Button as needed until the preset number (P1- P6) you wish to set is displayed, then press and hold the Presets Button to enter setting mode. 3. Press the or Buttons to tune the radio to the desired station (hold to scan for the next clear station). 4.
Using the iBT210 Pairing Your Bluetooth Device When in Bluetooth mode, the iBT210 will attempt to autolink to a previously paired device. If no device is paired, the iBT210 will automatically enter pairing mode for 3 minutes. You can manually initiate pairing without turning on the iBT210 by following steps 1-3 below. 1. Make sure your Bluetooth device is fully charged. Turn on your Bluetooth device and make it “discoverable” by turning on Bluetooth mode (check in Options or Settings) . 2.
Using the Playing Audio via Bluetooth iBT210 Press the Power/Alarm Reset Button to turn the unit ON. Press and release the Mode Button as needed until “BT” appears on the display.. Press the Play/Pause/Pairing Button on the unit to play audio from your linked Bluetooth device. Press the or Buttons to go to the previous or next track. Press and hold for fast forward or fast reverse within the track. 5. Press the or Buttons to adjust the volume on the unit.
Using the Playing Audio via Aux-In iBT210 1. Connect one end of a standard audio cable (not included) into the aux-in jack on the back of the unit and the other end into the headphone or output jack of your audio device. 2. Press the Power/Alarm Reset Button on the unit to turn it on. 3. Press and release the Mode Button as needed until the AUX indicator icon and “MP3” appear on the display. 4. Place your audio device in play mode. Navigate tracks and adjust output volume on the device. 5.
Using the Charging Devices via USB Port iBT210 1. Connect the standard size end of a USB cable (not included) to the USB Port on back of the unit and connect the other end to the charging port on your device. It’s often best to use the charging cable supplied with your device. 2. Monitor the charging on your device. Some devices use a proprietary charging method and will not charge using the USB Port. If this happens, you must charge your device using the charger that came with it.
Using the Battery Use Cautions and Tips iBT210 • Only use the recommended/supplied batteries or equivalent • Use alkaline batteries for longer life • Do not mix old and new batteries, and do not mix alkaline, carbon-zinc or rechargeable nickel-cadmium batteries • Insert batteries with proper polarity (+/–) as indicated • Remove exhausted batteries from product • Recharge rechargeable batteries under adult supervision • Do not attempt to recharge non-rechargeable batteries • Do not open batteries or heat
Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
iBT210 FCC Information FCC ID: EMOIBT210 IC: 986B-IBT210 FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
Troubleshooting Unit doesn’t respond (no power) • • • Check that all connections are correct and properly plugged in. Make sure your device is properly paired with the iBT210. Make sure the Power is ON. Unit doesn’t respond (locked up or frozen) • The unit may need to be reset. To do so, unplug the unit from power source and remove the backup batteries. Let unit stand for 2 minutes. Re-install backup batteries and connect unit to power source.
Limited 1 Year Warranty iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
