Model: iBT22 IB (English) Size: 153mm x 120mm Printing color: Black Date : Jan 15, 2013 P1 iBT22 Bluetooth Wireless Dual Alarm Clock instruction manual
P2 Introduction iBT22 Thank you for purchasing the iHome iBT22. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod, computer, PDA or other Bluetooth audio device. Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic operation and care of the unit. Please read them carefully and keep for future reference. Maintenance • Place the unit on a level surface away from sources of direct sunlight or excessive heat.
P3 iBT22 FCC Information FCC Radiation Exposure Statement FCC ID: EMOIBT22 IC: 986B-IBT22 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
P4 Information FCC Déclaration FCC quant à l'exposition à la radiation iBT22 FCC ID: EMOIBT22 Cet équipement est conforme aux limites FCC relatives à l'exposition à la radiation par radiofréquences IC: 986B-IBT22 établies pour les environnements non contrôlés. Cet émetteur ne doit pas être colocalisé ou utilisé en conjonction avec tout autre émetteur ou antenne. Cet appareil est conforme à la norme RSS-210 des règlements relatifs aux circuits intégrés.
P5 Table of Contents iBT22 Included/ Meet Your iBT22............................................................................................. 1-2 Installing Clock Backup Batteries .........................................................................................3 The Display/ Setting Up the Unit/ Turning the Unit ON and OFF ..............................................4 Setting the Time/ Daylight Saving Time ................................................................................
P6 iBT22 Included WARNING NOT FOR USE WITH TABLETS • iBT22 Alarm Clock • 100V-240V universal AC adaptor sleep alm.
P7 Meet Your iBT22 Top iBT22 Back Rest Lower Volume Button Sleep Button Raise Volume Button Alarm Reset/Power Button Fwd/+ Setting Button Alarm 1 Button Alarm 2 Button Rev/– Setting Button Play/Pause Button Snooze Dimmer Button Back USB Charging Port DC Jack Bluetooth/Pairing Button Aux-in Jack Clock Adj.
P8 Replacing & Installing Clock Backup Batteries Using the iBT22 The iBT22 uses 3 AAA batteries (installed) for backup to provide continuous alarm operation and clock settings in the event of a power failure. If the backup batteries have been installed and a power failure occurs or the AC adaptor is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings.
P9 Using the The Display iBT22 Bluetooth Indicator DST indicator Battery Low Indicator PM Indicator SLEEP AUX-IN Alarm 1 & Alarm 2 Indicators Sleep Indicator Aux-in Indicator PM Time Display Year/Date Indicator PM AM ALM. YEAR DATE Alarm time AM/PM Indicator Alarm Time/Date Display Setting Up the Unit 1. Connect the included AC adaptor to the DC jack located on the back of the unit and connect the other end to a working wall outlet. Turning the Unit ON and OFF 1.
P10 Using the Setting the Time iBT22 1. Press and hold the Clock Adjust Button (located on the back of the unit) until the time flashes in the display and a beep sounds. 2. Press and release the – or + Buttons to adjust the clock to the current time (hold to advance or reverse rapidly). Make sure to set the correct AM/PM time. The PM indicator appears to the left of the time display; there is no AM indicator. 3. Press and release the Clock Adjust Button.
P11 Using the Setting the Alarms iBT22 1. By default, the unit selects the most recently linked Bluetooth device as your wake-to source. If no Bluetooth device is detected, the iBT22 will automatically default to buzzer alarm. See page 8 to setup your Bluetooth device. Note: make sure you have an hour of audio on your Bluetooth device. 2. Press and hold the Button until the current alarm time flashes in the lower part of the display and a beep sounds. Press the – or + Button to set the alarm time.
P12 Using the Snooze Operation iBT22 1. Press and hold the Snooze/Dimmer Button for a few seconds to enter set snooze timer mode. A beep will sound and the display will flash. Press the – or + Button to set the snooze timer from 1 to 29 minutes. Press the Snooze/Dimmer Button to exit. Two confirmation beeps will sound. 2. Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again after the set snooze time.
P13 Using the Using Bluetooth: Pairing Your Device iBT22 NOTE: See the iBT22 Bluetooth Connection Guide for complete pairing details. Whenever it is powered on, this unit will attempt to autolink to a previously paired device. If no device is detected, the unit will automatically enter pairing mode for 2 minutes. You can manually initiate pairing without turning on the unit by following steps 1-3 below. 1. Make sure your Bluetooth device is fully charged.
P14 Using the iBT22 Pairing with a Different Device 1. When you power ON the speaker, it will automatically link with the previously paired Bluetooth device as long as that device is still within range (approx. 30 feet). So, to pair with a different device you must turn off the Bluetooth capability of the already paired device. Playing Audio Via Bluetooth 1. Press the Button to turn on the unit. The Bluetooth icon will be displayed when a linked device is in range and detected.
P15 Using the Playing Audio via Aux In 1. Connect one end of a 3.5mm stereo audio cable to the Aux-in jack on the back of the unit and connect the other end to the headphone or line-out jack on your audio device. 2. Press the Button on the unit to turn it on. 3. Power on the audio device and use the controls on the device to play or pause audio, and navigate tracks. 4. Press the or Button to adjust the system volume. You can also adjust volume on your device. 5.
P16 Using the Sleep Operation iBT22 Sleep mode lets you sleep to your Bluetooth device until the unit shuts off at a selected time. It will send a power off command to your device,too 1. Press the Sleep Button to enter sleep mode. The Sleep Icon will appear on the display to indicate it is in sleep mode. 2. Press the Sleep Button as needed to adjust the sleep timer from 120,90, 60, 30 or 15 minutes (or turn sleep mode OFF by pressing the Button). 3.
P17 Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
P18 8. Attachments – Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 10.
P19 Troubleshooting Unit doesn’t respond (no power) • Check that all connections are correct and properly plugged in. • Make sure your device is properly paired with the iBT22. • Make sure the Power is ON, indicated by “ON” appearing briefly on the display. Resetting the Unit If Bluetooth function is not operating properly, you may wish to reset Bluetooth. To do so, press and hold the Button for 10 seconds. You will hear a beep and the Bluetooth icon will be gone from the display.
P20 Limited 1 Year Warranty iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
