iWBT400 Eng IB Size: 153mm x 120mm Printing color: Black Mar 20, 2017 P1 Model: iWBT400 Bluetooth Dual Alarm Clock Radio with USB Charging instruction manual Questions? Contact Customer Service at 1-800-288-2792
P2 iWBT400 Introduction Thank you for purchasing the iHome iWBT400. This product is designed to provide high quality wireless sound for your Bluetooth audio device and to charge your Apple Watch. This instruction booklet explains the basic operation and care of the unit. Please read it carefully and keep for future reference. Maintenance • Place the unit on a level surface away from sources of direct sunlight or excessive heat.
P3 iWBT400 Table of Contents What’s Included ................................................................................................................................................ 3 Meet Your iWBT400....................................................................................................................................... 4 The Display/Setting Up the Unit...............................................................................................................
P4 iWBT400 What’s Included • iWBT400 unit • 2 x AA batteries • 100V-240V universal AC adapter iWBT400 universal AC adapter 3 2 x AA batteries
P5 iWBT400 Meet Your iWBT400 Sleep/Clock Adjust Button Top Presets Button Alarm 1 Button Alarm 2 Button Mode Button Microphone Volume Down/ Volume Up Buttons End Call/ Minus Settings Button Power/ Alarm Reset Button Answer Call/ Plus Settings Button Apple Watch Magnetic Charging Module Snooze/Display Dimmer Button Play/Pause/Pairing Button Back Backup Battery Compartment DC 7.5V 2.3A DC Jack Aux-in Jack AA x 2 push to open DC USB Charging Port 7.5V 2.
P6 Using the The Display iWBT400 Time Display PM/AM Indicators Aux-in Mode Indicator Set Wake-to Sleep Mode Indicator Alarm Active Indicator Bluetooth/Pairing FM Radio Low Backup Indicator Battery Mode Indicator Indicator Alarm Time/Date/Radio Frequency Wake to source: BT (Bluetooth), FM Radio, Buzzer Mode: BT (Bluetooth), FM Radio, Aux Setting Up the Unit RESET R ESET TEST Connect the included AC adapter to the DC jack located on the back of the unit and connect the other end to a working wall
P7 Using the Replacing and Installing Clock Backup Batteries iWBT400 Note: 2 AA batteries are included with the unit. Install them before using the unit. This model is equipped with a battery backup circuit that will maintain the time and alarm time settings in the event of a temporary power interruption (the display is NOT lit). The battery backup circuit will also operate the buzzer alarm to wake you up at the selected wake up time even if the power is out.
P8 Using the Setting the Clock 3/01/2017 iWBT400 This unit has a Daylight Saving Time (DST) Switch located under the battery compartment door. By default it is set to Auto and will automatically adjust the clock at the start and end of daylight saving time. If your location does not observe daylight saving time, move the switch to the -1 position before setting the clock. Press and hold the Sleep/Clock Adjust Button for 2 seconds until the clock display flashes and a beep sounds. 2.
P9 Using the Setting and Using the Alarms (Continued) 1. 2. 3. 4. 5. 6. 7. 8. iWBT400 Press and hold the Alarm Button for 2 seconds until the alarm time display and alarm icon flash. A beep sounds. Press the or Buttons to adjust the alarm time to the desired time (hold for rapid setting). Make sure you set the correct AM/PM alarm time. The AM and PM indicators appear to the left of the display. Press the Alarm Button to confirm the alarm time setting. The alarm schedule will flash.
P10 Using the Snooze/Display Dimmer Button 1. 2. 3. 4. 5. iWBT400 To program Snooze, press and hold the Snooze/Display Dimmer Button for 2 seconds during normal operation (when no alarm is sounding). Press the or Buttons to select the desired snooze time (between 01 and 29 minutes). Press and release the Snooze/Display Dimmer Button to confirm Snooze setting. 2 beeps will sound.
P11 Using the Setting and Using FM Presets iWBT400 The unit allows you to store up to 6 FM radio station presets 1. Press and release the Mode Button as needed until the FM indicator icon appears on the display. 2. Press and release the Presets Button as needed until the preset number (P1- P6) you wish to set is displayed, then press and hold the Presets Button to enter setting mode. 3. Press the or Buttons to tune the radio to the desired station (hold to scan for the next clear station). 4.
P12 Using the Pairing Your Bluetooth Device iWBT400 Whenever AC power is connected, the iWBT400 will attempt to autolink to a previously paired device. If no device is paired, the iWBT400 will automatically enter pairing mode for 2 minutes. For manual pairing, follow steps below. 1. Make sure your Bluetooth device (audio source) is turned on with Bluetooth mode enabled (check in the device’s Settings). 2. Press the Power/Alarm Reset Button to turn on the unit. 3.
P13 Using the Playing Audio via Bluetooth iWBT400 1. Press the Power/Alarm Reset Button to turn the unit ON. 2. Press and release the Mode Button as needed until “BT” appears on the display.. 3. Press the Play/Pause/Pairing Button on the unit to play audio from your linked Bluetooth device. 4. Press the or Buttons to go to the previous or next track. 5. Press the or Buttons to adjust the volume on the unit. You may need to adjust the volume on your device, too. 6.
P14 Using the Playing Audio via Aux-In 1. 2. 3. 4. 5. 6. iWBT400 Connect one end of a standard stereo 3.5mm audio cable into the aux-in jack on the back of the unit and the other end into the headphone or output jack of your audio device. Press the Power/Alarm Reset Button on the unit to turn it on. Press and release the Mode Button as needed until the AUX indicator icon and “AUX” appear on the display. Place your audio device in play mode. Navigate tracks and adjust output volume on the device.
P15 Using the Charging Devices via USB Port 1. Connect the standard size end of a USB cable (not included) to the USB Port on back of the unit and connect the other end to the charging port on your device. It’s often best to use the charging cable supplied with your device. DC iWBT400 7.5V 2.5A 2. Monitor the charging on your device. Some devices use a proprietary charging method and will not charge using the USB Port. If this happens, you must charge your device using the charger that came with it.
P16 Using the Battery Use Cautions and Tips • • • • • • • • • • • • • iWBT400 Only use the recommended/supplied batteries or equivalent Use alkaline batteries for longer life Do not mix old and new batteries, and do not mix alkaline, carbon-zinc or rechargeable nickel-cadmium batteries Insert batteries with proper polarity (+/–) as indicated Remove exhausted batteries from product Recharge rechargeable batteries under adult supervision Do not attempt to recharge non-rechargeable batteries Do not open b
P17 Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
P18 iWBT400 FCC Information FCC ID: EMOIWBT400 IC: 986B-IWBT400 FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
P19 Unit doesn’t respond (no power) • • • Troubleshooting Check that all connections are correct and properly plugged in. Make sure your device is properly paired with the iWBT400. Make sure the Power is ON. Unit doesn’t respond (locked up or frozen) • The unit may need to be reset. To do so, unplug the unit from power source and remove the backup batteries. Let unit stand for 2 minutes. Re-install backup batteries and connect unit to power source.
P20 Limited 1 Year Warranty iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
