User's Manual

For Models That Use Lithium Batteries
• Lithium batteries can explode or cause burns if disassembled, shorted,
recharged, exposed to water, fire, or high temperatures & not handled
appropriately
• Do not place loose batteries in a pocket, purse, or other container
containing metal objects, do not mix with used or other battery types, or
store with hazardous or combustible materials.
• Store in cool, dry, ventilated area.
• Follow applicable laws and regulations for transport and disposal.
A Consumer Guide to Product Safety
IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed and manufactured to ensure
your personal safety. However, improper use can result in potential electrical shock or fire
hazards. Please read all safety and operating instructions carefully before installation and use,
and keep these instructions handy for future reference. Take special note of all warnings listed
in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a
bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere
with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or
similar surface that may block ventilation openings. Also, it should not be placed in a
built-in installation, such as a bookcase or cabinet, which may impede the flow of air
through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat
registers, stoves or other appliances (including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. It is always best
to have a clear area from where the cable exits the unit to where it is plugged into an AC
socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance
section of this manual for cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids
are not spilled into any openings or vents located on the
product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and
disconnect the antenna or cable system during a lightning storm or when it is left unattended
and unused for long periods of time. This will prevent damage to the product due to
lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel
when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such
as a month or longer, the power cable should be unplugged from the unit to prevent
damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods
described in the user’s operating instructions. Service methods not covered in the
operating instructions should be referred to qualified service personnel.
Questions? Visit www.ekids.com
Maintenance
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish.
A cloth or other protective material should be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger
cleaning agents such as thinner or similar materials can damage the surface of the unit.
Limited 90 Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this
product to be free from defects in workmanship and materials, under normal use and conditions,
for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store
where it was originally purchased. Should this fail to resolve the matter and service still be required
by reason of any defect or malfunction during the warranty period, SDI will repair or, at its
discretion, replace this product without charge. This decision is subject to verification of the
defect or malfunction upon delivery of this product to the Factory Service Center authorized by
SDI Customer Service. The product must include proof of purchase, including date of purchase.
An out-of-warranty fee for service will be charged for units that are received without proof of
purchase.
Before returning this product for service, please first replace the batteries (if applicable) with
fresh ones, as exhausted or defective batteries are the most common cause of problems
encountered.
If service is still required:
1. Call SDI Customer Service at 1-800-288-2792 for Return Authorization and for the
address of the Factory Service Center.
2. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated
box SDI is not responsible for damage that occurs during shipping to the Factory Service
Center.
3. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the
date of purchase, if within the warranty period. Also include your name and address
information, a brief description for why the unit is being returned, and the return
authorization number. No unit can be processed without a return authorization number.
4. Write the return authorization number on the side of the shipping package and send the
unit prepaid and insured to the Factory Service Center address authorized by SDI
Customer Service.
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover (i) products which have been damaged by negligence or willful actions, misuse
or accident, or which have been modified or repaired by unauthorized persons; (ii) cracked or
broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s
or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service
Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the
product other than to the original purchaser. In no event will SDI or any of its affiliates, contractors,
resellers, their officers, directors,
shareholders, members or agents be liable to you or any third party for any consequential or
incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do
not allow limitations on implied warranties or exclusion of consequential damages, so these
restrictions may not apply to you.) This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned
disclaimer of warranty is contractually binding to you upon your transfer of currency (money
order, cashier's check, or credit card) for purchase of your SDI product.
Questions? Visit www.ekids.com
For any other questions: 1-800-288-2792 Toll Free
© 1976, 2014 SANRIO CO., LTD.
Used Under License.
eKids/KIDdesigns, Inc.
iHome® is a registered trademark of
©2014 SDI Technologies, Inc. All Rights Reserved.
Si-B42-140616-A Printed in China
FCC ID: EMOSIB42
IC: 986B-SIB42
Model: Si-B42 (Front)
IB (English)
Size: 432Wmm x 400Hmm
Color: Print in Black color
Date: June 16, 2014
FCC Information
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure
and compliance.
This device complies with Part 15 of the FCC Rules, operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
• Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
QDID: B021180
IMPORTANT
Read before proceeding
If you have any question regarding the operation or use of this product, please visit
www.ihome.com to view answers to frequently asked questions.
To learn more about this and other iHome products, please visit us online at www.ihome.com
iHome
Charging the Si-B42 CHARGE BEFORE USE/
Carga del Si-B42 CARGAR ANTES DE USAR/
Charger Si-B42 A CHARGER AVANT TOUTE UTILISATION
Bluetooth Mode/Modo Bluetooth/
Mode Bluetooth
Computer USB port/
Puerto USB del
ordenador/
Port USB de l'ordinateur
USB AC adaptor
(not included)/
Adaptador de CA
USB (no incluido)/
Adaptateur secteur
USB (non fourni)
USB AC adaptor
connected to working outlet
Adaptador USB CA conectado
a una salida de trabajo
Computer
connected to
working outlet/
Ordenador conectado a una
toma en funcionamiento/
Ordinateur connecté à une
prise sous tension
Toma de
Audio/Carga
Prise audio / charge
to play/
para reproducir/
pour lancer la lecture
to play/para reproducir/pour lancer la lecture
Press to pair/
Pulsar para emparejar/
Appuyez pour coupler
LED/
Témoin
Micro USB plug/
Conector micro USB/
Connecteur micro USB
3.5mm audio plug/
Conector de audio de 3.5 mm
Prise audio 3,5 mm
Standard USB plug/
Conector USB estándar/
Connecteur USB standard
Combination cable/Cable de combinación/
Câble combiné
NOTE: Do not play a connected Aux device while a linked Bluetooth device is
playing.
NOTA: No reproduzca un dispositivo Auxiliar conectado mientras que se esté
reproduciendo un dispositivo Bluetooth vinculado.
REMARQUE : Ne lancez pas la lecture à partir d'un appareil auxiliaire connecté
pendant qu'un autre appareil Bluetooth connecté est.
Aux-in Mode/Modo de entrada Aux/Mode Entrée auxiliaire
Mobile Phone
Teléfono móvil
Téléphone mobile
Game Devices
Dispositivos de juego
Consoles de jeu
iPod
Laptop
Ordenador portátil
Ordinateur portable
PC/Tablet
PC/Tableta
PC/Tablette
MP3/MP4
Interruptor
Auxiliar/OFF/Bluetooth
Commutateur Marche /
Arrêt /Bluetooth
Botón Bluetooth
Emparejamiento
Touche de couplage
Bluetooth
Adaptateur secteur USB connecté
à une prise sous tension
Model Si-B42
Bluetooth
Rechargeable
Speaker
CHARGE
BEFORE
USE
Questions? Visit www.ekids.com
© 1976, 2014 SANRIO CO., LTD.
Charging the Si-B42
The Si-B42 is powered by a rechargeable battery in the speaker. Make sure to
charge speaker before use.
• Connect the micro-USB plug to the Audio/Charging jack on the speaker.
• Connect the larger USB plug to a powered USB port, such as that on a
computer. Your computer should be connected to a wall outlet when speaker
is charging. The light on the speaker will turn to solid red while charging and
turn off when fully charged.
If you start to notice sound distortion at higher volumes, it's time to recharge
the batteries.
Using Bluetooth with the Si-B42
• Slide the of OFF/AUX/BT Switch on the speaker to the Bluetooth position
(BT). The light will flash blue and a tone will sound as the Si-B42 will search
for a connected device.
• Press the Blutton on the back of the Si-B42, the LED will flash blue and
red and a tone will sound, indicating the Si-B42 is in pairing mode.
• Place your audio device in Bluetooth mode (often found in the device’s
Settings or Tools menu) and make it “discoverable”. “HelloKittySi-B42”
should appear on your device. If “Not Connected” or similar message
appears, select it to connect. If your device asks for a passcode, enter ‘1234’.
• If no device is paired within 3 minutes, the unit will revert to auto link mode.
To retry pairing, press and replease the Bluetooth Pairing Button ( ).
• Once paired, the light will glow solid blue. You can then stream audio to the
speaker. If pairing is not successful, turn the power OFF on the speaker and
repeat pairing procedure.
• To listen to Bluetooth audio, make sure the OFF/AUX/BT Switch on the
speaker is in Bluetooth (BT) position.
• Control Bluetooth audio from your device.
Remember to turn off the speaker and your device after listening.
NOTE: When unit is charging, the blue light will appear solid red.
Using the Si-B42 with Aux Devices
• Connect the micro-USB plug to the Audio/Charging jack on the
speaker.
• Connect the stereo 3.5mm audio plug to the headphone jack or line-out of
any audio device.
• Slide the OFF/AUX/BT Switch on the speaker to the AUX position. The
blue LED will glow solid blue, indicating AUX mode.
• Press play on your audio device and adjust its volume to listen to audio.
• When done listening, move the OFF/AUX/BT Switch to the OFF position to
turn the unit off. Remember to turn off your audio device, too.
Audio/
Charging Jack
Bluetooth Pairing Button
Off/Aux/Bluetooth Switch
Front View/Parte frontal/Face avant
Back View/Posterior/ Face arrière
Back View/Posterior/ Face arrière