Installation Guide

ManualsBrandsSea Gull Lighting ManualsFlush Mount LightsTo-mKin 6-in Heirloom Bronze Transitional Flush Mount Light

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

ASSEMBLY

GENERAL

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU

ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED

OR THE CIRCUIT BREAKER OFF .

You don’t need special tools to install this fixture. Be sure to follow the

steps in the order given. Under no circumstances should a fixture be

hung on house electrical wires, nor should a swag type fixture be

installed on a ceiling which contains a radiant type heating system.

Read instructions carefully. If you are unclear as to how to proceed,

consult a qualified electrician.

Carefully remove the fixture from the carton and check that all parts

are included, as shown in Figure 1 & 2. Be careful not to misplace

any of the screws or parts which are needed to install this fixture.

IF SOCKET IS NOT ATTACHED - FOLLOW THE NEXT 3 STEPS.

GREEN

GROUNDING SCREW (R)

*OUTLET BOX

SCREWS

MOUNTING

BAR (A)

*WIRE

CONNECTORS

MOUNTING

SCREWS (I)

*GROUND WIRE

*OUTLET BOX

GROUNDING AND MOUNTING BAR LOCK UP

FIGURE 2

*NOT INCLUDED

FIGURE 1

*NOT SUPPLIED

*OUTLET

BOX

FIXTURE

MOUNTING

SCREWS (I)

*WIRE

CONNECTORS

MOUNTING

BAR (A)

*OUTLET

BOX SCREWS

IF SUPPLY WIRES ARE LOCATED WITHIN 3” OF

BALLAST, USE WIRE RATED FOR AT LEAST 90˚C.

WARNING: FOR FIXTURES PROVIDED WITH 75˚ C

OR 90˚ C SUPPLY WIRE WARNING ONLY (THESE

WARNINGS ARE PROVIDED ON THE U.L. LABEL

AND ON THE FIXTURE CARTON).

WARNING: RISK OF FIRE. MOST DWELLINGS

BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED

60˚ C. CONSULT A QUALIFIED ELECTRICIAN

BEFORE INSTALLING.

STEP 1:

STEP 2:

STEP 3:

Twist ends of socket wires together.

Pass wires through round hole (C) in canopy (D).

Insert socket (E) in rectangular hole (F) by placing bracket (G)

on an angle to engage the back notch(H). Pull forward to snap in.

CANOPY (D)

RETAINING

SCREWS (O)

KEY SLOTS (N)

RECTANGULAR

HOLE (F)

ROUND HOLE (C)

BRACKET (G)

SOCKET (E)

BACK NOTCH (H)

DIFFUSER

NOTE: FOR FIXTURE EMPLOYING A GROUNDED

CONVENIENCE OUTLET

CAUTION: “THIS FIXTURE EMPLOYS A GROUNDED TYPE

RECEPTACLE AND IS NOT INTENDED FOR CONNECTION

TO A TWO WIRE UNGROUNDED SOURCE OF SUPPLY.”

Installation And Safety

Instruction

HC-109

092800

Fill In Item Number On Carton And

File This Sheet For Fixture Reference. ITEM#_______________

Summary of content (2 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS ASSEMBLY FOR YOUR SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF . GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully.
PAGE 2
INSTALLATION HC-109 IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX. STEP 1: Secure mounting bar (A) to outlet box with outlet box screws (not supplied). Raised side is top as illustrated. STEP 2: Thread fixture mounting screws (I) into threaded holes of mounting bar (A) 3 turns each. STEP 3: A. Take note of the color of the wire(s) on your fixture.