Installation Guide

ManualsBrandsSea Gull Lighting ManualsFlushmount LightsCentra 2-Light Brushed Stainless Flushmount

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

GENERAL

ASSEMBLY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU

ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED

OR THE CIRCUIT BREAKER SET AT OFF.

You don't need special tools to install this fixture. Be sure to follow

the steps in the order given. Under no circumstances should a

fixture be hung on house electrical wires, nor should a swag type

fixture be installed on a ceiling which contains a radiant type heating

system. Read instructions carefully. If you are unclear as to how

to proceed, consult a qualified electrician.

*OUTLET BOX

*WIRE

CONNECTOR

MOUNTING

BAR (A)

CENTER

HOLE (K)

NUT (B)

BRACKET (I)

NIPPLE (C)

CANOPY (E)

CAP NUT (F)

GLASS (H)

RING (G)

TABS (L)

BALL NUTS (J)

* GROUND

WIRE

GREEN

GROUNDING

SCREW (D)

NIPPLE (C)

*OUTLET BOX

SCREWS

MOUNTING

BAR (A)

*WIRE

CONNECTORS

*GROUND WIRE

*OUTLET BOX

GROUNDING AND MOUNTING BAR LOCK UP

FIGURE 1

*NOT INCLUDED

FIGURE 2

*NOT INCLUDED

NUT (B)

*OUTLET

BOX SCREWS

Carefully remove the fixture from the carton and check that all parts

are included, as shown in figure 1 and 2. Be careful not to misplace

any of the screws or parts which are needed to install this fixture.

STEP 1:

Before mounting canopy (E ) to mounting bar (A), place canopy (E)

on flat surface. Next place ring (G) over canopy (E) making sure the

three brackets (I) protrude through holes in canopy (E). If they do not,

adjust the brackets (I) so that they align with the canopy (E) holes.

NOTE: IF LIGHT LEAKAGE IS PRESENT, SLIGHTLY BEND THE

BRACKETS (I) TOWARDS THE CEILING.

NOTE: FOR FIXTURES PROVIDED WITH 75˚ C OR

90˚ C SUPPLY WIRE WARNING ONLY- (THESE

WARNINGS ARE PROVIDED ON THE U.L. LABEL

AND ON THE FIXTURE CARTON): RISK OF FIRE.

MOST DWELLINGS BUILT BEFORE 1985 HAVE

SUPPLY WIRE RATED 60˚ C. CONSULT A

QUALIFIED ELECTRICIAN BEFORE INSTALLING.

IF SUPPLY WIRES ARE LOCATED WITHIN 3” OF

BALLAST, USE WIRE RATED FOR AT LEAST 90˚C.

Installation And Safety

Instruction

HC-175

092800

Fill In Item Number On Carton And

File This Sheet For Fixture Reference. ITEM#_______________

Summary of content (2 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY ASSEMBLY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER SET AT OFF. Carefully remove the fixture from the carton and check that all parts are included, as shown in figure 1 and 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture. STEP 1: GENERAL You don't need special tools to install this fixture.
PAGE 2
INSTALLATION HC-175 IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX. STEP 1: Secure mounting bar (A) to outlet box with outlet box screws (not supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed above nut (B). Thread nipple (C) into mounting bar (A) and secure with nut (B). STEP 2: A. Take note of the color of the wire(s) on your fixture.