Installation Guide

NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
CAUTION:
To reduce the risk of electrical shock, provide a watertight
seal between the fixture and the mounting surface by using a silicone
or similar caulking.
Install lamps.
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar offset strap (C). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the mounting
bar offset strap (C). If uninsulated ground wire is on the mounting bar
offset strap (C), connect the ground wire from the fixture (if supplied)
and the outlet box to it using a small wire connector (not supplied) (See
Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
*NOTE: When parallel wire is used, the tracer wire is square shaped or
ridged, and the less tracer wire is round in shape or smooth. (Seen best
when viewed from wire end.) To separate wires, grasp the ends of each
wire and pull apart.
Insert fixture mounting screws (I) in threaded holes of mounting bar
offset strap (C). Run fixture mounting screws (I) all the way down to
their heads.
After wires are connected, tuck them carefully inside the outlet box.
Position backplate (M) over mounting screws (I) and secure in place
by threading cap nuts (N) onto mounting screws (I).
Make sure no bare wires can be seen outside wire connectors.
NOTE: IF GLASS PANELS ARE NOT INSTALLED, PLEASE
FOLLOW THIS STEP: PLACE BOTTOM EDGE OF GLASS INTO
CHANNEL. BEND TABS OVER EDGE TO SECURE IN PLACE.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box.
DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Place mounting bar offset strap (C) against outlet box (not supplied)
and secure in place using outlet box screws (not supplied). Be sure
t
he mounting screws (I) are perfectly horizontal so fixture hangs
straight.
I
MPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your handcrafted, solid brass lighting fixture has been coated
with a durable, baked on acrylic lacquer which gives maximum
protection against the weather. In time, however, the brightness
of the brass will tarnish giving way to an authentic old world
brass finish.
NOTE: To keep your solid polished brass fixture looking new
for years to come, regularly apply a good quality non-abrasive
car wax to all metal surfaces, giving the fixture an extra
protective coating.
I
NSTALLATION HC-1331
STEP 1:
STEP 2:
STEP 3:
S
TEP 4:
FINAL ASSEMBLY
S
TEP 1:
STEP 1:
WET LOCATION
CLEANING
ORDERING PARTS