Installation Guide

Install lamp (A) by gently twisting into socket (B) (see figure 3).
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed fr
om wire end.) T
o separate wir
es, grasp the ends
of each wire and pull apart.
I
nsert fixture mounting screws (I) in threaded holes of universal
mounting bar (J). Run screws all the way down to the heads.
After wires are connected, tuck them carefully inside the outlet box.
Position backplate (M) over mounting screws (I) and secure in place
with cap nuts (H).
N
OTE: IF GLASS PANELS ARE NOT INSTALLED, PLEASE
FOLLOW THIS STEP: PLACE BOTTOM EDGE OF GLASS INTO
CHANNEL. BEND TABS OVER EDGE TO SECURE IN PLACE.
A
.
T
ake note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
B. T
ake your fixtur
e wire(s) fr
om group A and place evenly against
the black wir
e from the outlet box.
DO NOT twist wir
es together
befor
e using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm r
esistance.
D. Gently try to remove the wir
es from the connector
. If you can
r
emove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner
.
P
lace universal mounting bar (J) against outlet box (not suppplied)
and secure in place using outlet box screws (K) (not supplied). Be
sure the mounting screws (I) are perfectly horizontal so fixture hangs
straight.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Y
our handcrafted, solid brass lighting fixtur
e has been coated with
a durable, baked on acrylic lacquer which gives maximum
protection against the weather. In time, however, the brightness of
the brass will tarnish giving way to an authentic old world brass
finish. NOTE: To keep your solid polished brass fixture looking new
for years to come, regularly apply a good quality non-abrasive car
wax to all metal surfaces, giving the fixture an extra protective
coating.
INSTALLATION HC-1383 STEP 4:
GROUNDING INSTRUCTIONS: Connect the supply ground wire,
f
ixture ground wire using UL approved wire nuts. Gently try to remove
the wires from the connector. If you can remove the wires, carefully re-
do the wiring connection.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
STEP 2:
STEP 3:
Make sure no bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1:
STEP 2:
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
NOTE: FOR
FIXTURES
LABELED FOR
WET LOCA
TION AND
USED
OUTDOORS.
CAUTION: To reduce the risk of electrical shock, provide a watertight
seal between the fixtur
e and the mounting surface by using a silicone
or similar caulking.
WET LOCATION
FIGURE 3
FIXTURES
WITH A ONE
PIECE LAMP /
BALLAST
COMBINATION
LAMP (A)
SOCKET (B)
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LA
WS.
SEE WWW.LAMPRECYCLE.ORG
*PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED)
BLACK WHITE
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE