Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
housing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure bare
wires cannot be seen outside the terminal block. Tighten down
on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable into
track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
FOR YOUR SAFETY HC-203
011100
WARNING: Be sure the electricity to the wires you are work-
ing on is shut off; either the fuse removed or the circuit
breaker off.
WARNING-RISK OF SHOCK. 24V SYSTEM NOT SUITABLE
FOR OUTDOOR USE.
INSTALLATION AND SAFETY INSTRUCTIONS
1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
housing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure bare
wires cannot be seen outside the terminal block. Tighten down
on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable into
track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
FOR YOUR SAFETY HC-203
011100
WARNING: Be sure the electricity to the wires you are work-
ing on is shut off; either the fuse removed or the circuit
breaker off.
WARNING-RISK OF SHOCK. 24V SYSTEM NOT SUITABLE
FOR OUTDOOR USE.
INSTALLATION AND SAFETY INSTRUCTIONS
1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
housing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure bare
wires cannot be seen outside the terminal block. Tighten down
on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable into
track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
FOR YOUR SAFETY HC-203
011100
WARNING: Be sure the electricity to the wires you are work-
ing on is shut off; either the fuse removed or the circuit
breaker off.
WARNING-RISK OF SHOCK. 24V SYSTEM NOT SUITABLE
FOR OUTDOOR USE.
INSTALLATION AND SAFETY INSTRUCTIONS
1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
housing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure bare
wires cannot be seen outside the terminal block. Tighten down
on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable into
track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
FOR YOUR SAFETY HC-203
011100
WARNING: Be sure the electricity to the wires you are work-
ing on is shut off; either the fuse removed or the circuit
breaker off.
WARNING-RISK OF SHOCK. 24V SYSTEM NOT SUITABLE
FOR OUTDOOR USE.