06170 UNDERWATER HOUSING for SONY DSC-RX100/DSC-RX100M2 日本語 MDX-RX100/Ⅱ English 取扱説明書 Instruction Manual
Introduction Thank you for purchasing SEA&SEA products. Please read this instruction manual carefully prior to using this product. Only with a thorough understanding of this manual’s content will you be able to use the housing correctly. After reading the manual, please be sure to keep it in a place where you can easily come back to it at any time.
Safety Precautions For safe handling of the product, please read the following precautions carefully before use. Failure to heed the precautions listed below could result in serious consequences. To prevent injury or damage to yourself and/or others, please observe the precautions as they contain highly important information related to personal and product safety. WARNING Situations that could result in severe injury or death. CAUTION Situations that could result in property damage or personal injury.
Safety Precautions Do not rest heavy weight on the product. It might deform the outer casing, damage internal parts, make the waterproofing fail, or result in fire or electric shock. Please note that some marks may be left on the camera scraping against the dials or gears of the housing. Handle the product carefully so as not to scratch the front port, the lens, the flash window or the finder.
Precautions on Handling the O-ring This product is kept watertight by the O-ring. To keep the O-ring functioning properly, please observe the following. Improper handling of the O-ring could cause flooding. CAUTION SEA&SEA products use blue O-rings. These O-rings are impregnated with silicone oil through a special process. The lubricating effect of the O-ring lasts as long as the silicone oil is gradually seeping out from within.
Precautions on Handling the O-ring Coat with silicone grease Silicone grease protects the O-ring from chafing. After checking the O-ring to make sure that there are no scratches, dust, or debris, apply a light coating of silicone grease to the entire O-ring with your finger. Applying too much grease will make it easier for dust and debris to adhere to the O-ring, and could cause flooding.
Identification of Parts Accessory shoe Fiber-optic cable socket Zoom lever Shutter lever Control dial Lock knob Mount for SA8 fixed flash base Port*1(M67 screw) Front case Power button Mode dial Movie-record button MENU button Monitor window Selection button LCD monitor hood holder Tripod socket (bottom) Control wheel Delete button Playback button Fn button Rear case *1 A wide-angle conversion lens or an M67→M62 Step Down Ring can be screwed onto the front.
Preparation for Setting Up This product must be used in combination with the optional equipment (digital camera, port, strobe, accessories etc.) for underwater photography. In order to set up the equipment, prepare each item correctly. Prepare the housing [With the RX-100M2] • Attach four rear cushion rubbers (small) on the rear window (four positions). Rear cushion rubber (small) [With the RX-100] • Attach four rear cushion rubbers (large) on the rear window (four positions).
Preparation for Setting Up Maintaining the O-ring O-ring This product is kept watertight by the O-ring. To keep the O-ring functioning properly, please observe the following before setting up. Make sure to remove the O-ring when maintaining. For detailed O-ring maintenance methods, please see the O-ring maintenance manual. CAUTION Make sure to fit/install the O-ring into the groove properly after maintenance.
Opening and Closing the Housing Opening and closing the housing is done with the lock knob. Here we will explain how to open and close the lock knob. Opening the lock knob 1 Push the tab outward to unlock as indicated by ①, and rotate the lock knob clockwise as indicated by ② to lift the rear cover from the front case (Fig. 1) Tab Fig.1 2 Pull the rear case to open (Fig.2) CAUTION E-9 Before opening the rear case, make sure that the housing is completely dry and free of salt deposits.
Opening and Closing the Housing パチン錠を閉める Closing the locking lock knob 1 Close the rear case, and rotate the lock knob counterclockwise Lock knob CAUTION Before aligning the rear case and front case, make sure there are no specks of dust, acratches, or deformities on the O-ring and O-ring contact surfaces. Check to make sure that the locking lock knob is securely locked.
Mounting the Camera in the Housing CAUTION To avoid flooding by trapping, remove the strap / protective cover / metal strap clips from camera before installation. 1 Place the anti-reflective tape on the lens nameplate (part A) on the camera Part A Anti-reflective tape Fig.1 2 Turn off the power of the camera and place it as shown in Fig.2 Fig.
Mounting the Camera in the Housing 3 Make sure that there is no dust or scratches on the O-ring / O-ring contact surface before closing the rear case. Then close the rear case and close the lock knob See: “Opening and Closing the Housing” (P. E-9) Fig.3 CAUTION A substantial difference between the external (water) and the internal (camera and air) temperatures sometimes result in dewfall on the inside surface of the housing lens.
Connecting the Strobe Connect the strobe with the fiber-optic cable (option) when the strobe is triggered by sensing the light from the camera's built-in flash. 1 2 Remove the fiber-optic cable socket caps Fiber-optic cable socket cap Insert the fiber-optic cable's connector into the socket until it stops Do not remove the caps from fiber-optic cable sockets not in use to keep light from entering in.
External Controls Zoom lever Zoom lever Move the lever to the left and right to control the zooming. Control dial Rotate the dial to control the control ring of the camera. Shutter lever Shutter lever Push down the lever to control the shutter of the camera. Control dial Mode dial Mode dial Rotate the dial to switch the camera mode. Control wheel Rotate this dial to control the camera.
Attaching the Hand Strap 1 Push one end of the hand strap through the hook on the housing, insert the other end through the loop produced, and then pull the strap tight as shown CAUTION Do not use the strap when out of water if using optional accessories (such as a wide-angle conversion lens, stay, arm, and strobe / light). The increased weight of the accessories may damage the strap and the strap hook, which may result in equipment damage / loss or personal injury.
Attaching the Optional Accessories This product accepts SEA&SEA optional accessories. By using this product in combination with those accessories, you will be able to try various shooting techniques. CAUTION Lenses, strobes and other accessories have different depth rating. Check the depth rating for each before use. Read the instruction manual for each accessory before use.
Attaching the Optional Accessories Accessory shoe Strobes / lights can be mounted to the accessory shoe by using optional Mini Shoe Arm (29511) or Hot Shoe Arm (29501) or SA8 Ball Base for Accessory Shoe (22120). CAUTION The max. weight of an accessory that can be mounted to the accessory shoe is approx. 1050g / 36.75oz . Remove the accessories from the accessory shoe when carrying the housing out of water.
Attaching the Optional Accessories Leak sensor The optional leak sensor (46115) can be attached on this product.
Maintenance and Storage CAUTION Never use chemicals, cosmetics, any petroleum solvents such as paint thinner, or neutral detergent on the product. They may deform and damage the product. After each use in salt water, make sure it’s watertight, then soak it sufficiently in fresh water. Insufficient soaking causes damage by salt to the product. Salty residue may be left on the product where it will crystallize as it evaporates.
Specifications Compatible camera Sony DSC-RX100/DSC-RX100M2 Controls Control dial, Shutter lever, Zoom lever, Power button, Mode dial, Movie-record button, MENU button, Selection button, Control wheel, Delete button, Playback button, Fn button Construction Body: Corrosion-resistant aluminum alloy Depth rating 100m (330ft) Dimensions Approx. 147(W)×97(H)×117(D) mm Weight Approx.
シーアンドシー・サンパック株式会社 〒145-0062 東京都大田区北千束1-4-6 TEL.03-5701-5533 カスタマーサービスセンター TEL.048-255-8512 http://www.seaandsea.co.jp SEA&SEA SUNPAK Co., Ltd. 1-4-6, Kitasenzoku, Ohta-ku, Tokyo, Japan 145-0062 TEL. +81-3-5701-5533 World Customer Service Center TEL. +81-48-255-8512 http://www.seaandsea.jp 1130-Z-01A (2014年1月現在 / Current as of Jan.
