06160 UNDERWATER HOUSING for Fujifilm X10 日本語 MDX-X10 English 取扱説明書 Instruction Manual
Introduction Thank you for purchasing SEA&SEA products. Please read this instruction manual carefully prior to using this product. Only with a thorough understanding of this manual’s content will you be able to use the housing correctly. After reading the manual, please be sure to keep it in a place where you can easily come back to it at any time.
Safety Precautions For safe handling of the product, please read the following precautions carefully before use. Failure to heed the precautions listed below could result in serious consequences. To prevent injury or damage to yourself and/or others, please observe the precautions as they contain highly important information related to personal and product safety. WARNING Situations that could result in severe injury or death. CAUTION Situations that could result in property damage or personal injury.
Safety Precautions Do not rest heavy weight on the product. It might deform the outer casing, damage internal parts, make the waterproofing fail, or result in fire or electric shock. Please note that some marks may be left on the camera scraping against the dials or gears of the housing. Handle the product carefully so as not to scratch the front port, the lens, the flash window or the finder.
Precautions on Handling the O-ring This product is kept watertight by the O-ring. To keep the O-ring functioning properly, please observe the following. Improper handling of the O-ring could cause flooding. CAUTION SEA&SEA products use blue O-rings. These O-rings are impregnated with silicone oil through a special process. The lubricating effect of the O-ring lasts as long as the silicone oil is gradually seeping out from within.
Precautions on Handling the O-ring Coat with silicone grease Silicone grease protects the O-ring from chafing. After checking the O-ring to make sure that there are no scratches, dust, or debris, apply a light coating of silicone grease to the entire O-ring with your finger. Applying too much grease will make it easier for dust and debris to adhere to the O-ring, and could cause flooding.
Identification of Parts Accessory shoe Mode dial Fn button Fiber-optic cable socket Fiber-optic cable socket adapter SA8 M10 Fixed Ball Base Socket Shutter lever Lock knob Port*1(M67 screw) Hinge bracket Front case Power/ZOOM dial Focus mode selector dial Flash close lever Flash pop-up button Main command dial Exposure compensation dial AFL/AEL button Sub command dial Playback button RAW button AF/Playback zoom out button WB button AE/Playback zoom in button Tripod socket (bottom) MENU/OK butto
Preparation for Setting Up This product must be used in combination with the optional equipment (digital camera, port, strobe, accessories etc.) for underwater photography. In order to set up the equipment, prepare each item correctly. Prepare the housing and port The port on this product is built into the housing and thus cannot be removed. Maintaining the O-ring O-ring This product is kept watertight by the O-ring.
Opening and Closing the Housing Opening and closing the housing is done with the lock knob. Here we will explain how to open and close the lock knob. Opening the lock knob 1 2 Push the tab outward to unlock as indicated by ①, and rotate the lock knob clockwise as indicated by ② to lift the rear cover from the front case (Fig. 1) Pull the rear case to open (Fig.2) Tab Fig.1 CAUTION Before opening the rear case, make sure that the housing is completely dry and free of salt deposits.
Opening and Closung the Housing パチン錠を閉める Closing the locking lock knob 1 Close the rear case, and rotate the lock knob counterclockwise Lock knob CAUTION Before aligning the rear case and front case, make sure there are no specks of dust, acratches, or deformities on the O-ring and O-ring contact surfaces. Check to make sure that the locking lock knob is securely locked.
Mounting the Camera in the Housing CAUTION To avoid flooding by trapping, remove the strap / protective cover / metal strap clips from camera before installation. 1 Place the anti-reflective tape on the lens nameplate (part A) on the camera ON ASPH ER IC A L FU J IN LE NS SUP -2. C ＝ 7.1 .0 EB 8 ER ｆ -28.4 mm 1: 2 Part A 2 Anti-reflective tape Fig.1 Push the gear for the power/zoom dial into the lens part of the camera until it stops Zoom ring Gear for Power/Zoom dial 3 Fig.
Mounting the Camera in the Housing 4 5 Turn off the power of the camera and place it as shown in Fig.4 Make sure that there is no dust or scratches on the O-ring / O-ring contact surface before closing the rear case. Then close the rear case and close the lock knob Fig.4 See: “Opening and Closing the Housing” (P. E-9) CAUTION A substantial difference between the external (water) and the internal (camera and air) temperatures sometimes result in dewfall on the inside surface of the housing lens.
Connecting the Strobe Connect the strobe with the fiber-optic cable (option) when the strobe is triggered by sensing the light from the camera's built-in flash. 1 2 Remove the fiber-optic cable socket caps Fiber-optic cable socket cap Insert the fiber-optic cable's connector into the socket until it stops Do not remove the caps from fiber-optic cable sockets not in use to keep light from entering in.
Use the camera’s built-in flash If planning to use the built-in flash on the camera, remove the fiber socket adapter from the housing. 1 Fiber-optic cable socket adapter Remove the two screws for the fiber-optic cable socket adapter on the housing by inserting the accompanying hexagon wrench into each and turning counterclockwise The fiber-optic cable socket adapter can be removed with the fiber-optic cable socket cap attached. Please make sure not to lose the removed parts.
External Controls Power / ZOOM dial By rotating the dial as indicated, you can turn the power ON/OFF and change the zoom angle. Power / Zoom dial Due to how the port on the housing is structured, the zoom range on the camera is limited to 85 mm on the tele side. Focus mode selector dial Turn the dial up and down to change the operation mode. Focus mode selector dial Shutter lever Mode dial Depress the shutter lever to press the shutter button of the camera.
External Controls Main command dial Rotate the dial to enable operation. In addition, you can also change the settings in M mode by pushing the button in the middle of the dial. Main command dial Sub command dial Rotate the dial to enable operation. In addition, you can select items using the top and bottom or right and left buttons (▲、▼、 、 ) instead of the selector button on the camera.
Attaching the Hand Strap 1 Push one end of the hand strap through the hook on the housing, insert the other end through the loop produced, and then pull the strap tight as shown CAUTION Do not use the strap when out of water if using optional accessories (such as a wide-angle conversion lens, stay, arm, and strobe / light). The increased weight of the accessories may damage the strap and the strap hook, which may result in equipment damage / loss or personal injury.
Attaching the Optional Accessories This product accepts SEA&SEA optional accessories. By using this product in combination with those accessories, you will be able to try various shooting techniques. CAUTION Lenses, strobes and other accessories have different depth rating. Check the depth rating for each before use. Read the instruction manual for each accessory before use.
Attaching the Optional Accessories Accessory shoe Strobes / lights can be mounted to the accessory shoe by using optional Mini Shoe Arm (29511) or Hot Shoe Arm (29501) or SA8 Ball Base for Accessory Shoe (22120). CAUTION The max. weight of an accessory that can be mounted to the accessory shoe is approx. 1050g / 36.75oz . Remove the accessories from the accessory shoe when carrying the housing out of water.
Maintenance and Storage CAUTION Never use chemicals, cosmetics, any petroleum solvents such as paint thinner, or neutral detergent on the product. They may deform and damage the product. After each use in salt water, make sure it’s watertight, then soak it sufficiently in fresh water. Insufficient soaking causes damage by salt to the product. Salty residue may be left on the product where it will crystallize as it evaporates.
Specifications Compatible camera Fujifilm X10 Controls ON/OFF/Zoom dial, Focus mode selector dial, Shutter lever, Fn button, Mode dial, Flash pop-up button, Flash close lever, Exposure compensation dial, Main command dial, AFL/AEL button, MENU/OK button, Sub command dial, RAW button, DISC/BACK button, WB button, AF/playback zoom out button, AE/playback zoom in button, Playback button Construction Body: Corrosion-resistant aluminum alloy Depth rating 100m (330ft) Dimensions Approx.
シーアンドシー・サンパック株式会社 〒145-0062 東京都大田区北千束1-4-6 TEL.03-5701-5533 カスタマーサービスセンター TEL.048-255-8512 http://www.seaandsea.co.jp SEA&SEA SUNPAK Co., Ltd. 1-4-6, Kitasenzoku, Ohta-ku, Tokyo, Japan 145-0062 TEL. +81-3-5701-5533 World Customer Service Center TEL. +81-48-255-8512 http://www.seaandsea.jp 1130-Z-01A (2012年3月現在 / Current as of Mar.
