Product Manual Seagate® Desktop HDD ST4000DM000 ST3000DM003 Gen 15 100710254 Rev.
Document Revision History Revision Date Description of Change Rev. A 01/14/2013 Initial release. © 2013 Seagate Technology LLC. All rights reserved. Publication number: 100710254, Rev. A January 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/ or other countries.
Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1 About the SATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Desktop HDD Product Manual, Rev.
Figures Figure 1 Figure 2 Attaching SATA cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Mounting dimensions (3TB and 4TB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Desktop HDD SATA Product Manual, Rev.
Desktop HDD SATA Product Manual, Rev.
Seagate Technology Support Services For information regarding online support and services, visit http://www.seagate.com/www/en-us/about/ contact_us/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance For information regarding data recovery services, visit http://www.i365.
Desktop HDD SATA Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® Desktop HDD model drives: ST4000DM000 ST3000DM003 These drives provide the following key features: • High instantaneous (burst) data-transfer rates (up to 600MB per second). • TGMR recording technology provides the drives with increased areal density. • State-of-the-art cache and on-the-fly error-correction algorithms.
Introduction Note 10 www.seagate.com The host adapter may, optionally, emulate a master/slave environment to host software where two devices on separate SATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical SATA environment. Desktop HDD SATA Product Manual, Rev.
2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST4000DM000 2.1 ST3000DM003 Specification summary tables The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual.
Drive Specifications www.seagate.
www.seagate.com Drive Specifications 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137GB. 2.
Drive Specifications 2.5 www.seagate.com Physical characteristics Maximum height 26.11mm / 1.028 in Maximum width 101.6mm / 4.0 in ( ± 0.010 in) Maximum length 146.99mm / 5.787 in Typical weight 610g / 1.345 lb Cache buffer 64MB 2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics.
www.seagate.com Drive Specifications • Read/write power and current Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms delay, then a 16-sector read followed by a 32-ms delay. • Operating power and current Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads) and 20 percent drive idle mode.
Drive Specifications www.seagate.com 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10MHz.
www.seagate.com Drive Specifications activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disk access is necessary. 2.9 Environmental specifications This section provides the temperature, humidty, shock, and vibration specifications for Desktop HDDs. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000ft.
Drive Specifications www.seagate.com 2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80 Gs based on half-sine shock pulses of 10ms during read operations. Shocks should not be repeated more than two times per second. 2.9.5.
www.seagate.com Drive Specifications 2.10.1 Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 3897) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. 2.
Drive Specifications www.seagate.com Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea.
www.seagate.com Drive Specifications 2.14.2 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard.
Desktop HDD SATA Product Manual, Rev.
3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
Configuring and Mounting the Drive www.seagate.com Figure 1 Attaching SATA cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Desktop HDD drives support latching SATA connectors. 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 2 for drive mounting dimensions.
4.0 SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6. For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
SATA Interface www.seagate.com Table 5 SATA connector pin definitions (continued) Segment Power Pin Function Definition P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.3V power, pre-charge, 2nd mate P4 Ground 1st mate P5 Ground 2nd mate P6 Ground 2nd mate P7 V5 5V power, pre-charge, 2nd mate P8 V5 5V power P9 V5 5V power P10 Ground 2nd mate P11 Ground or LED signal If grounded, drive does not use deferred spin P12 Ground 1st mate.
Table 6 SATA standard commands (continued) Command name Command code (in hex) Download Microcode 92H Execute Device Diagnostics 90H Flush Cache E7H Flush Cache Extended EAH Format Track 50H Identify Device ECH Idle E3H Idle Immediate E1H Initialize Device Parameters 91H Read Buffer E4H Read DMA C8H Read DMA Extended 25H Read DMA Without Retries C9H Read Log Ext 2FH Read Multiple C4H Read Multiple Extended 29H Read Native Max Address F8H Read Native Max Address Extended
SATA Interface www.seagate.com Table 6 SATA standard commands (continued) Command name Command code (in hex) Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable/Disable Autosave B0H / D2H S.M.A.
www.seagate.com SATA Interface 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on page 26. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
SATA Interface www.seagate.com Table 7 Identify Device commands (continued) Word Description Value 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB).
www.seagate.com SATA Interface Table 7 Identify Device commands (continued) Word Description Value 92 Master password revision code FFFEH 93 Hardware reset value xxxxH 94 Automatic acoustic management 8080H 95–99 ATA-reserved 0000H 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
SATA Interface 32 www.seagate.com 5 GPL feature set is supported. 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported. 7 WRITE DMA QUEUED FUA EXT command is supported. 8 64-bit World Wide Name is supported. 9-10 Obsolete. 11-12 Reserved for TLC. 13 IDLE IMMEDIATE command with IUNLOAD feature is supported. 14 Shall be set to 1. 15 Shall be cleared to 0. Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported.
www.seagate.com SATA Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
SATA Interface www.seagate.com 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
Index A ACA 20 acceleration 18 acoustics 18 Active 16 Active mode 16 Agency certification 19 altitude 17 Ambient temperature 17 ambient temperature 14 areal density 13 ATA commands 26 Australia/New Zealand Standard AS/NZ CISPR22 20 Australian Communication Authority (ACA) 20 Australian C-Tick 20 Average latency 14 Average seek time 14 B buffer 14 C cables and connectors 23 cache 14 capacity 12 CE mark 19 certification 19 Check Power Mode 26 China RoHS directive 21 compatibility 19 Conducted noise 16 Conduct
N noise 16 nominal power 14 Nonoperating shock 18 Nonoperating vibration 18 O operating 15 Operating power 15 Operating shock 18 Operating vibration 18 P Physical characteristics 14 point-to-point 9, 23 Power consumption 14 power dissipation 15 Power modes 16 Power specifications 14 Power-management modes 16 Power-on to Ready 14 precautions 23 printed circuit board 23 programmable power management 16 prominent discrete tone 19 Q quick reference 11 R Radiated RF immunity 19 radio and television interference
U UL60950-1 19 V voltage 14 Voltage dips, interrupts 19 Voltage tolerance 16 W weight 14 wet bulb temperature 17 width 14 Write Buffer 28 Write DMA 28 Write DMA Extended 28 Write DMA FUA Extended 28 Write DMA Without Retries 28 Write Log Extended 28 Write Multiple 28 Write Multiple Extended 28 Write Multiple FUA Extended 28 Write Sectors 28 Write Sectors Extended 28 Write Sectors Without Retries 28 Desktop HDD SATA Product Manual, Rev.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100710254, Rev.
