Product Manual Barracuda 7200.11 Serial ATA ST31000333AS ST3640323AS ST3320613AS ST3320813AS ST3160813AS 100507013 Rev.
Revision history Revision Rev A Rev. B Date 06/17/08 06/25/08 Sheets affected or comments Initial release 4 and 6. Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100507013, Rev. B, June 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . .
ii Barracuda 7200.11 Serial ATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting dimensions (1000 & 640 GB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting dimensions (320 & 160 GB models) . . . . . . . . . . . . . . . . . . . . .
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Barracuda® 7200.11 Serial ATA model drives: ST31000333AS ST3640323AS ST3320613AS ST3320813AS ST3160813AS These drives provide the following key features: • 7,200 RPM spindle speed. • High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST31000333AS ST3640323AS ST3320613AS ST3320813AS ST3160813AS Specification summary tables The specifications listed in the following tables are for quick reference.
Table 1: 4 Drive specifications summary for 1000 and 640 Gbyte models Drive specification ST31000333AS ST3640323AS Formatted capacity (512 bytes/sector)* 1000 Gbytes 640 Gbytes Guaranteed sectors 1,953,525,168 1,250,263,728 Heads 6 4 Discs 3 2 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 1300 kbits/in max Track density 182 ktracks/in avg Areal density 228 Gbits/in2 avg Spindle speed 7,200 RPM Intern
Drive specification ST31000333AS Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs Vibration, nonoperating 5–22 Hz: 2.0 Gs 22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs ST3640323AS Drive acoustics, sound power Idle** 2.9 bels (typical) 3.1 bels (max) 2.7 bels (typical) 2.9 bels (max) Performance Seek 3.2 bels (typical) 3.3 bels (max) 3.1 bels (typical) 3.2 bels (max) Quiet Seek 3.1 bels (typical) 3.2 bels (max) 3.0 bels (typical) 3.
Table 2: 6 Drive specifications summary for 320 and 160 Gbyte models Drive specification ST3320613AS ST3320813AS ST3160813AS Formatted capacity (512 bytes/sector)* 320 Gbytes 160 Gbytes Guaranteed sectors 625,142,448 312,581,808 Heads 2 1 Discs 1 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 1250 kbits/in max Track density 182 ktracks/in avg Areal density 219 Gbits/in2 avg Spindle speed 7,200 RPM Int
Drive specification ST3320613AS ST3320813AS Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs Vibration, nonoperating 5–22 Hz: 2.0 Gs 22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs ST3160813AS Drive acoustics, sound power Idle** 2.5 bels (typical) 2.7 bels (max) Quiet Seek 2.6 bels (typical) 2.8 bels (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.
2.1 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST31000333AS 1000 Gbytes 1,953,525,168 512 ST3640323AS 640 Gbytes 1,250,284,896 512 ST3320613AS ST3320813AS 320 Gbytes 625,142,448 512 ST3160813AS 160 Gbytes 312,581,808 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.1.
2.4 Physical characteristics Maximum height 1000 & 640 GB models 26.1 mm (1.028 inches) 320 & 160 GB models 20.17 mm (0.794 inches) Maximum width 101.6 mm (4.000 +/- 0.010 inches) Maximum length 146.99 mm (5.787 inches) Typical weight 1000 GB models 677 grams (1.493 lbs) 640 GB models 543 grams (1.199 lbs) 320 & 160 GB models 368 grams (0.811 lbs) Cache buffer ST31000333AS & ST3640323AS 32 Mbytes (32,768 kbytes) ST3320613AS 16 Mbytes (16,384 kbytes) ST3320813AS and ST3160813AS 2.
2.6 Start/stop times 1000 GB Models Power-on to Ready (sec) 640 GB Models 20 (max) Power-on to Ready (sec) (2.0 Amp Code Option) 11 (max) Standby to Ready (sec) 15 (max) Ready to spindle stop (sec) 10 (max) 2.7 320 & 160 GB Models 14 (max) 15 (max) Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 2 on page 20. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 9.
Table 3: DC power requirements Power dissipation (3-disc values shown) Avg (watts 25° C) Avg 5V typ amps Avg 12V typ amps Spinup — — 3.0 (peak) Idle* 7.96 0.320 0.530 Idle* (with offline activity) 9.29 0.610 0.520 Operating (40% r/w, 40% seek, 20% inop.) 11.16 0.600 0.680 Seeking (random, 20% idle) 10.42 0.500 0.660 Standby 0.99 0.150 0.020 Sleep 0.99 0.150 0.020 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T.
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters). Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.8.
2.8.5.2 Nonoperating shock 1000 & 640 GB models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration.
2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.
2.11 Reliability 2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of 0.34% (MTBF of 0.7 million hours) when operated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifications in Section 2.8 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics that are not relevant to individual units.
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
2.13 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.
3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling. • Use only 6-32 UNC mounting screws. • The screws should be inserted no more than 0.150 inch (3.
Figure 4. Mounting dimensions (320 & 160 GB models) 22 Barracuda 7200.11 Serial ATA Product Manual, Rev.
4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.1 Hot-Plug compatibility Barracuda 7200.
4.2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors.. Table 7: Segment Signal Serial ATA connector pin definitions Pin Function Definition S1 Ground 2nd mate S2 A+ Differential signal pair A from Phy S3 A- S4 Ground 2nd mate S5 B- Differential signal pair B from Phy S6 B+ S7 Ground 2nd mate Key and spacing separate signal and power segments Power P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.
4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 2.6 (http:// www.sata-io.org). See “S.M.A.R.T. commands” on page 32.for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Security Erase Unit F4H Security Freeze F5H Security Set Password F1H Security Unlock F2H Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep 99H or E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T.
4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 8 on page 25. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
Word Description Value 60–61 Total number of user-addressable LBA sectors available (see Section 2.1 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes). Drives with capacities over 137 Gbytes will have 0FFFFFFFh in this field and the actual number of user-addressable LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature.
Word Description Value 108–111 The mandatory value of the world wide name (WWN) for the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support. Each drive will have a unique value. 112–127 ATA-reserved 0000H 128 Security status 0001H 129–159 Seagate-reserved xxxxH 160–254 ATA-reserved 0000H 255 Integrity word xxA5H Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note.
30 Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported. 6 Ultra DMA mode 6 is supported. 8 Ultra DMA mode 0 is currently active. 9 Ultra DMA mode 1 is currently active. 10 Ultra DMA mode 2 is currently active. 11 Ultra DMA mode 3 is currently active. 12 Ultra DMA mode 4 is currently active.
4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
5.0 Seagate Technology support services Online services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index A ACA 17 acceleration 14 acoustics 15 Active 12 Active mode 12 actuator arm 10 AFR 16 Agency certification 16 altitude 13 Ambient temperature 13 ambient temperature 9, 10 Annualized Failure Rate 16 Annualized Failure Rate (AFR) 16 areal density 1, 8 ATA commands 25 Australia/New Zealand Standard AS/NZS3548 1995 17 Australian Communication Authority (ACA) 17 Australian C-Tick 17 Average latency 9 Average seek time 9 B buffer 9 C cables and connectors 20 cache 9 capacity 8 case temperature 13 CE mark
I I/O data-transfer rate 8 I/O duty cycle 16 Identify Device 25 Identify Device command 27 Idle 12, 25 Idle Immediate 25 Idle mode 10, 12 IEC950 16 Information Technology Equipment (ITE) 16 Initialize Device Parameters 25 Input noise ripple 11 input voltage 10 interface 8, 23 interference 17 internal data-transfer rate OD 8 is 9 ISO document 7779 15 ITE 16 Operating power 10 Operating shock 13 Operating vibration 14 P Physical characteristics 9 point-to-point 2, 20 Power consumption 10 power consumption 1
RMS read/write current 11 RoHS 18 RRL 17 S S.M.A.R.T. Disable Operations 26 S.M.A.R.T. Enable Operations 26 S.M.A.R.T. Enable/Disable Autosave 26 S.M.A.R.T. Execute Offline 26 S.M.A.R.T. implementation 25 S.M.A.R.T. Read Attribute Thresholds 26 S.M.A.R.T. Read Data 26 S.M.A.R.T. Read Log Sector 26 S.M.A.R.T. Return Status 26 S.M.A.R.T. Save Attribute Values 26 S.M.A.R.T.
38 Barracuda 7200.11 Serial ATA Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100507013, Rev. B, Printed in U.S.A.