Product Manual Seagate® Desktop HDD Formerly Barracuda 7200.14 ST3000DM001 ST750DM003 ST2000DM001 ST500DM002 ST1500DM003 ST320DM000 ST1000DM003 ST250DM000 Gen 14 100686584 Rev.
Document Revision History Revision Date Description of Change Rev. A 08/19/2011 Initial release. Rev. B 09/01/2011 Updated decibel specifications, start/stop times; Table 3; mounting drawing. Rev. C 10/20/2011 Updated voltage tolerance specifications. Rev. D 01/17/2012 Corrected Table 1 (Altitude, operating) specification and Table 5 (Idle2). Rev. E 06/11/2012 Updated Index. Rev. F 09/05/2012 Added 2.5A spin-up code option (Table 1 and Table 2); page 17. Rev.
Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 About the SATA interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.
Figures Figure 1 Figure 2 Figure 3 Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Mounting dimensions (3-disk: 1.5TB to 3TB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Mounting dimensions (1-disk: 250GB to 1TB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Seagate Desktop HDD Product Manual, Rev.
Seagate Technology Support Services For information regarding online support and services, visit: http://www.seagate.com/about/contact-us/technical-support/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.
www.seagate.com 1.0 Introduction Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® Desktop HDD model drives: ST3000DM001 ST2000DM001 ST1500DM003 ST1000DM003 ST750DM003 ST500DM002 ST320DM000 ST250DM000 These drives provide the following key features: • 7200 RPM spindle speed. • High instantaneous (burst) data-transfer rates (up to 600MB per second). • TGMR recording technology provides the drives with increased areal density.
www.seagate.com Introduction 1.1 About the SATA interface The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels.
www.seagate.com 2.0 Drive Specifications Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST3000DM001 ST2000DM001 ST1500DM003 ST1000DM003 ST750DM003 ST500DM002 ST320DM000 ST250DM000 2.1 Specification summary tables The specifications listed in Table 1 and Table 2 are for quick reference.
www.seagate.com Drive Specifications Table 1 Drive specifications summary for 3TB, 2TB, 1.5TB, 1TB and 750GB models (continued) ST3000DM001; ST2000DM001; Drive Specification* ST2000DM001 ST1500DM003 ST1000DM003; ST750DM003 20°C per hour max (operating) 30°C per hour max (non-operating) Temperature gradient 5% to 95% (operating) 5% to 95% (non-operating) Relative humidity Relative humidity gradient (max) 30% per hour 37.7°C max (operating) 40.
www.seagate.
www.seagate.com Drive Specifications Table 2 Drive specifications summary for 500GB, 320GB and 250GB models (continued) Drive Specification* ST500DM002 ST320DM000 ST250DM000 5Hz to 22Hz: 3.0 Gs 22Hz to 350Hz: 3.0 Gs 350Hz to 500Hz: 3.0 Gs Vibration, non-operating Drive acoustics, sound power Idle*** 2.2 bels (typical) 2.3 bels (max) Seek 2.3 bels (typical) 2.4 bels (max) 1 per 1014 bits read Non-recoverable read errors Rated workload Average rate of <55TB/year.
www.seagate.com Drive Specifications 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137GB. 2.
www.seagate.com 2.5 Drive Specifications Physical characteristics Maximum height 3TB, 2TB and 1.5TB 1TB, 750GB, 500GB, 320GB, 250GB 26.1mm / 1.028 in 19.98mm / 0.787 in Maximum width (all models) 101.6mm / 4.0 in (± 0.010 in) Maximum length (all models) 146.99mm / 5.787 in Typical weight 3TB and 2TB 626g / 1.38 lb 1.5TB 535g / 1.18 lb 1TB and 750GB 400g / 0.88 lb 500GB, 320GB, 250GB 415g / 0.92 lb Cache buffer 2.6 3TB, 2TB, 1.
www.seagate.com 2.7 Drive Specifications Start/stop times 3-disk (3TB, 2TB models) 2-disk (2TB, 1.5TB models) Power-on to ready (in seconds) 15 (typical) 17 (max) Power-on to ready, 2.5A spin-up code option (in seconds, typical) <10 Standby to ready (in seconds) 15 (typical) 17 (max) Ready to spindle stop (in seconds) 10 (typical) 11 (max) 1-disk (1TB, 750GB models) 1-disk (250GB, 320GB, 500GB models) 10 (typical) 12 (max) 8.5 (typical) 10 (max) n/a 10 (typical) 12 (max) 8.
www.seagate.com Table 3 Drive Specifications DC power requirements (3-disk: 3TB and 2TB models) Power dissipation (3-disk values shown) Avg (watts 25° C) Avg 5V typ amps Avg 12V amps Spinup — — 2.0A or 2.8A Idle2* † 5.40 0.190 0.377 Operating 8.00 0.510 0.462 Standby 0.75 0.136 0.005 Sleep 0.75 0.136 0.005 Table 4 DC power requirements (2-disk: 2TB and 1.5TB models) Power dissipation (2-disk values shown) Avg (watts 25° C) Avg 5V typ amps Avg 12V amps Spinup — — 2.
www.seagate.com Drive Specifications 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10MHz.
www.seagate.com 2.9 Drive Specifications Environmental specifications This section provides the temperature, humidity, shock, and vibration specifications. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000ft. (305 meters), the maximum temperature is derated linearly by 1°C every 1000 ft. Refer to Section 3.4 on page 20 for base plate measurement location. 2.9.
www.seagate.com Drive Specifications 2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80 Gs based on half-sine shock pulses of 2 ms during read operations. Shocks should not be repeated more than two times per second. 2.9.5.
www.seagate.com Drive Specifications 2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note For seek mode tests, the drive is placed in seek mode only.
www.seagate.com Drive Specifications 2.12 Warranty To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/ From this page, click on “Check to see if the drive is under Warranty”. Users will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for the drive. 2.13 Agency certification 2.13.
www.seagate.com Drive Specifications 2.13.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.
www.seagate.com Drive Specifications 2.14.2 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard.
www.seagate.com 3.0 Configuring and Mounting the Drive Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
www.seagate.com 3.4 Configuring and Mounting the Drive Drive mounting Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 2 and Figure 3 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling. • Use only 6-32 UNC mounting screws.
www.seagate.com Configuring and Mounting the Drive Figure 3 Mounting dimensions (1-disk: 250GB to 1TB models) 5.787 in. max 146.99 mm 1.106 ± .050 in 28.09 ± 1.27 mm 0.626 ± .050 in 15.90 ± 1.27 mm TOP OF LABEL Temperature Check Point 4.010 in. max 101.85 mm Temperature Check Point 5 TYP CL OF DRIVE 0.814 in 20.68 mm CL OF CONNECTOR DATUM B 0.138 in 3.51 mm 4.00 in 101.60 mm 1.638 in 41.61 mm 1.22 ± .020 in 30.99 ± .51 mm 3X 6-32 UNC-2B 3 MINIMUM THREAD DEPTH 0.
www.seagate.com 4.0 SATA Interface SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6. For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
www.seagate.com 4.3 SATA Interface Supported ATA commands The following table lists SATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 3.0 (http://www.sata-io.org). See “S.M.A.R.T. commands” on page 30 for details and subcommands used in the S.M.A.R.T. implementation.
www.seagate.com SATA Interface Table 10 SATA standard commands (continued) Command name Command code (in hex) Security Freeze F5H Security Set Password F1H Security Unlock F2H Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep E6H S.M.A.R.T.
www.seagate.com SATA Interface 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on page 23. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
www.seagate.com SATA Interface Table 11 Identify Device commands (continued) Word Description Value 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB).
www.seagate.com SATA Interface Table 11 Identify Device commands (continued) Word Description Value 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
www.seagate.com SATA Interface 8 64-bit World Wide Name is supported. 9-10 Obsolete. 11-12 Reserved for TLC. 13 IDLE IMMEDIATE command with IUNLOAD feature is supported. 14 Shall be set to 1. 15 Shall be cleared to 0. Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported. 6 Ultra DMA mode 6 is supported.
www.seagate.com SATA Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
www.seagate.com SATA Interface 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
Index A ACA 16 acceleration 14 acoustics 15 Active 12 Active mode 12 Agency certification 16 altitude 13 Ambient temperature 13 ambient temperature 9, 10 areal density 8 ATA commands 23 Australia/New Zealand Standard AS/NZ CISPR22 16 Australian Communication Authority (ACA) 16 Australian C-Tick 16 Average latency 9 Average seek time 9 B buffer 9 C cables and connectors 19 cache 9 capacity 7 CE mark 16 certification 16 Check Power Mode 23 China RoHS directive 18 compatibility 16 Conducted noise 12 Conducted
N noise 12 nominal power 9 Nonoperating shock 14 Nonoperating vibration 14 O operating 11 Operating power 10 Operating shock 14 Operating vibration 14 P Physical characteristics 9 point-to-point 3, 19 Power consumption 10 power dissipation 11 Power modes 12 Power specifications 10 Power-management modes 12 Power-on to Ready 10 precautions 19 printed circuit board 19 programmable power management 12 prominent discrete tone 15 Q quick reference 4 R Radiated RF immunity 15 radio and television interference 17
U UL60950-1 16 V voltage 10 Voltage dips, interrupts 15 Voltage tolerance 12 W weight 9 wet bulb temperature 13 width 9 Write Buffer 24 Write DMA 24 Write DMA Extended 24 Write DMA FUA Extended 24 Write DMA Without Retries 24 Write Log Extended 24 Write Multiple 24 Write Multiple Extended 24 Write Multiple FUA Extended 24 Write Sectors 24 Write Sectors Extended 24 Write Sectors Without Retries 24 Seagate Desktop HDD Product Manual, Rev.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100686584, Rev.
