• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Barracuda 9 • • • • • • • • • Disc Drive • • • • • • • • • ST19171N/W/WD/WC/DC • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Installation Guide • • • • • • • • • • • • • • •
Contents Preface.........................................................................................1 Electrostatic discharge protection ................................................1 Important safety information and precautions.............................. 2 Wichtige Sicherheitshinweise ......................................................4 Regulatory agency compliance....................................................8 Seagate technical support services..........................................
Barracuda 9 Installation Guide, Rev. B 1 Preface This manual contains information for users of the Seagate® ST19171 Barracuda™ 9 SCSI disc drives. It provides support services, performance specifications, and initial setup information. Additional information is available in the Barracuda 9 Product Manual (part number 83329030). Contact your Seagate sales representative if you need to order this publication. Electrostatic discharge protection Caution.
2 Barracuda 9 Installation Guide, Rev. B • Turn off the power before removing or installing the DC power cable. • Do not remove any circuit boards from the drive. • Never use an ohmmeter on any circuit boards. • When installing the drive on a carrier or tray, discharge the carrier or tray prior to inserting it into the system. Important safety information and precautions Caution. Use forced-air ventilation when bench-testing the drive to ensure proper cooling of drive components.
Barracuda 9 Installation Guide, Rev. B 3 Always observe the following warnings and precautions: • Perform all maintenance by following the procedures in this manual. • Follow all cautions and warnings in the procedures. • Use sound safety practices when operating or repairing the unit. • Use caution when troubleshooting a unit that has voltages present. Turn off power to the unit before servicing it. • Wear safety shoes when removing or replacing heavy parts.
4 Barracuda 9 Installation Guide, Rev. B As a component, this drive is designed to be installed and operated in accordance with UL1950, EN60950, CSA C22.2 950M89, and VDE0805. Seagate takes all reasonable steps to ensure that its products are certifiable to currently accepted standards. Typical applications of these disc drives include customer packaging and subsystem design.
Barracuda 9 Installation Guide, Rev. B 5 aratur der Einheit. Einige Verfahren erfordern Spezialwerkzeuge; diese müssen zur sachgemäßen Ausführung der Wartungsarbeiten und aus Sicherheitsgründen den Empfehlungen entsprechend verwendet werden. Die Verfahren in diesem Handbuch und die Aufkleber auf dem Gerät enthalten Warn- und Vorsichtshinweise. Diese Hinweise sind sorgfältig durchzulesen und zu beachten, um das Risiko von Verletzungen auf ein Mindestmaß zu beschränken oder ganz zu vermeiden.
6 Barracuda 9 Installation Guide, Rev. B • Wenn eine Einheit unter Spannung steht, gehen Sie bei der Fehlerdiagnose besonders vorsichtig vor. Schalten Sie die Einheit aus, bevor Sie mit den Reparaturarbeiten beginnen. • Tragen Sie Sicherheitsschuhe, wenn Sie schwere Teile ausbzw. einbauen. • Wenn das Laufwerk in einem Einbaugestell oder Gehäuse montiert ist, sorgen Sie dafür, daß die Temperatur im Inneren des Gestells oder Gehäuses die für das Laufwerk vorgegebenen Grenzwerte nicht übersteigt.
Barracuda 9 Installation Guide, Rev. B 7 Als Teilkomponente ist dieses Laufwerk für die Installation und den Betrieb in Übereinstimmung mit UL 1950, EN60950, CSA C22.2 950-M89 und VDE0805 vorgesehen. Seagate ist ständig bemüht, die Zulassungsfähigkeit von Seagate-Produkten im Rahmen der gegenwärtig geltenden Standards zu gewährleisten. Zu den typischen Anwendungen dieser Festplattenwerke zählen Systemeinbau durch den Kunden und die Konstruktion von Untersystemen.
8 Barracuda 9 Installation Guide, Rev. B Regulatory agency compliance Electromagnetic susceptibility As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is the responsibility of those integrating the drive within their systems to perform those tests required and design their system to ensure that equipment operating in the same system as the drive or external to the system does not adversely affect the performance of the drive.
Barracuda 9 Installation Guide, Rev. B 9 Electromagnetic compliance for the European Union If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/336/EEC of 03 May 1989 as amended by Directive 92/31/ EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993.
10 Barracuda 9 Installation Guide, Rev. B Seagate technical support services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate® drive or other Seagate products, use one of the Seagate technical support services listed below.
Barracuda 9 Installation Guide, Rev. B 11 Seagate CompuServe forum Online technical support for Seagate products is available on CompuServe. To access our technical support forum, type go seagate. This forum provides information similar to that found on SeaBOARD. In addition, you can type questions or browse through previous questions and answers on the forum messages.
12 Barracuda 9 Installation Guide, Rev. B FAX services SeaFAX® You can use a touch-tone telephone to access Seagate’s automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Phone number Australia England USA 61-2-9756-5170 44-1628-894084 1-800-SEAGATE or 408-456-4496 Seagate technical support FAX You can FAX questions or comments to technical support specialists 24 hours daily. Responses are sent during business hours.
Barracuda 9 Installation Guide, Rev. B 13 Direct-support services Seagate technical support For one-on-one help, you can talk to a technical support specialist during local business hours. Before calling, note your system configuration and drive model number (STxxxx). Location Phone number Australia England 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M–F) 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M–F) 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M.
14 Barracuda 9 Installation Guide, Rev. B Customer service centers Seagate direct OEM, Distribution, and System Integrator customers should contact their Seagate service representative for warranty information. Other customers should contact their place of purchase. Seagate offers comprehensive customer support for all Seagate drives. These services are available worldwide.
Barracuda 9 Installation Guide, Rev. B 15 General description Barracuda 9 SCSI disc drives are high-speed, random-access digital-data storage devices. The drive is a component for installation in an enclosure designed for the drive. This is often a rack within the system or an external enclosure designed to house one or more disc drives or other peripheral units.
16 Barracuda 9 Installation Guide, Rev. B Characteristics Interface Capacity Unformatted Formatted2 Recording Cylinders (user) Read/write data heads Servo heads Seek time3 Average read Average write Disc rotation RPM Average latency Internal transfer rate (Mbits/sec, variable with zone) Max sync. SCSI transfer rate N W/WD/WC/DC Multi-segmented cache 1 Can ST19171 SCSI Fast-20 (also called Ultra SCSI)1 11.7 Gbytes 9.1 Gbytes 5,274 20 Embedded 9.7 msec 10.7 msec 7,200 ±0.5% 4.
Barracuda 9 Installation Guide, Rev. B 17 DC power requirements Voltage regulation5 Single-ended Differential +5V11 +12V +5V11 +12V ± 5% ± 5%2 ± 5% ± 5%2 Amps Maximum operating current1 0.93 0.89 1.17 0.89 Maximum starting current Peak DC 3, 6 Peak AC 3 0.92 — 2.18 3.1 1.04 — 2.18 3.1 Delayed motor start (max)1, 4 0.82 0.08 0.90 0.08 Peak operating current Typical DC 1 Maximum DC 1 Maximum (peak) 0.92 0.93 1.00 0.84 0.89 1.8 1.12 1.17 1.89 0.84 0.89 1.
18 Barracuda 9 Installation Guide, Rev. B 2A –10% tolerance is permissible during initial start of the spindle but must return to ±5% before reaching 7,200 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator. 3 See the +12V current profile in the Barracuda 9 Product Manual (publication number 83329030).
Barracuda 9 Installation Guide, Rev. B 19 11 No terminator power. See 11.7.3.4 in the Barracuda 9 Product Manual. 12 All power-saving features are enabled; ASA II code only. 13 Seeking is defined as a third-stroke seek at OD. The command is issued every 20 msec. 14 Read track is defined as repeat reads of track 15 with a duty cycle of: 78% for N drives, 32% for W drives, 48% for WC drives, 44% for WD drives, and 44% for DC drives.
20 Barracuda 9 Installation Guide, Rev. B Initial setup information The general information beginning on this page applies to all of the Barracuda 9 drive models. After reading the general information topics, refer to the appropriate drive-specific section listed below for additional information about configuring and installing your particular model.
Barracuda 9 Installation Guide, Rev. B 21 SCSI ID jumpers Each device on the SCSI chain must have a unique SCSI ID. The host system’s SCSI controller usually uses the highest-numbered ID available; therefore the lower-numbered SCSI IDs are normally used for other SCSI devices such as this Barracuda disc drive. Note. Most SCSI controllers (host adapters) allow you to skip a SCSI ID. For example, you can have ID0, ID1, and ID3 (skipping ID2).
22 Barracuda 9 Installation Guide, Rev. B The top example in Figure 2 shows an internal hard disc at one end of the SCSI bus with the SCSI controller at the other end (both are terminated). The bottom example shows two additional SCSI devices connected externally—this means the SCSI controller is no longer on the end of the SCSI chain and should not be terminated. Note. Some controllers prefer to remain terminated even if they are in the middle of the chain.
Barracuda 9 Installation Guide, Rev. B 23 Terminator power You usually will not need to change this option and can normally leave the drive configured as it was shipped from the factory. For information about how to change the terminator power option on your drive, refer to the appropriate drive-specific section. I/O circuits and data path widths • WD and DC models use differential I/O circuits. You cannot mix these models with single-ended models (N, W, WC) on the same SCSI bus.
24 Barracuda 9 Installation Guide, Rev. B Figure 3 shows two design approaches with one or more fans used to generate air flow. The air-flow patterns can be created by the fans either pushing or drawing air. The overall flow pattern can be directed from front to back, back to front, or side to side.
Barracuda 9 Installation Guide, Rev. B 25 Kühlung des Systems Die Gehäusekonstruktion muß eine ausreichende Kühlung des Laufwerkes gewährleisten. Die Umgebungstemperatur darf maximal 50°C betragen. Die Produkthandbuch Barracuda 9 (Dokument 83329030) enthalten Anweisungen zur Beurteilung der Luftstromkonstruktion. Die Beurteilung muß sicherstellen, daß sich die Gehäuset e m p e r a t u r b e s t i m m t e r k r i t i s c h e r Ko m p o n e n t e n b e i Laufwerkbetrieb innerhalb zugelassener Grenzen hält.
26 Barracuda 9 Installation Guide, Rev. B . SE AG AT E Above unit Über der Einheit Note. Air flows in the direction shown (back to front) or in reverse direction (front to back) Under unit Unter der Einheit Hinweis. Luftstrom in der angezeigten Richtung (von vorne nach hinten) oder in umgekehrter Richtung (von hinten nach vorne) SE AG AT E Above unit Über der Einheit Note. Air flows in the direction shown or in reverse direction (side to side) Hinweis.
Barracuda 9 Installation Guide, Rev. B 27 Mounting the drive and connecting cables Do not touch the connector pins or any components on the control board without observing static-discharge precautions. Always handle the drive by the frame only. The drive may be mounted in any orientation (horizontally, vertically, and any combination thereof); however, you must ensure that the drive receives adequate air flow for cooling. 1. Mount the drive to the host system’s chassis using four 6-32 UNC screws.
28 Barracuda 9 Installation Guide, Rev. B 1. Befestigen Sie das Laufwerk mit vier 6-32-UNC-Schrauben am Gehäuse des Host-Systems. Die beiden Seiten des Laufwerkes sind mit jeweils zwei Befestigungslöchern versehen, die Unterseite des Laufwerkes weist vier weitere Befestigungslöcher auf. Gemessen von der Außenfläche des Gehäuses dürfen die Schrauben maximal 3,81 mm in die Befestigungslöcher des Gehüuses hineinragen. Die Schrauben müssen gleichmäßig, jedoch nicht zu fest, angezogen werden.
Barracuda 9 Installation Guide, Rev. B 29 defined in IEC 950. Figure 4 provides the pin information for the DC power connector. To connect the DC power cable to the drive, simply insert the cable end into the drive’s DC power connector. 4. Schließen Sie das SCSI-Kabel an den SCSI-Steckverbinder des Laufwerkes an. Das Kabel darf nicht gedehnt oder gedrückt werden und es darf den Luftstrom zur Kühlung des Systems nicht behindern.
30 Barracuda 9 Installation Guide, Rev. B Note. Signal ground on the power control board (PCB) and the head and disc assembly (HDA) are connected together in this drive and you cannot separate them. The equipment in which you have mounted the drive is connected directly to the HDA and PCB without electrically isolating shock mounts. Maximizing the conductive contact area between HDA ground and system ground may reduce radiated emissions.
Barracuda 9 Installation Guide, Rev. B 31 tem einbauen. Die daraus u.U. resultierende verstärkte elektromagnetische Strahlung fällt in den Zuständigkeitsbereich des Systemdesigners. 5. Replace the host system’s cover. 5. Setzen Sie das Gehäuseoberteil des Host-Systems wieder auf. Formatting the drive Warning. Formatting a drive erases all user data. Be sure that you understand this principle before formatting any hard disc drive.
32 Barracuda 9 Installation Guide, Rev. B N drives Setting the SCSI ID N/ND jumpers drives section Use the J6 connector to set the SCSI ID (see Figure 5). To change the SCSI ID, install jumpers on the appropriate pins as shown in the illustration. Drive Front Jumper Plug (enlarged to show detail) Pin 1 J6 Reserved SCSI ID = 0 (default) SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Figure 5.
Barracuda 9 Installation Guide, Rev. B 33 N drives Terminating the drive ST19171N drives are terminated with permanently mounted IC active terminators. If you install one of these drives and it is not on the end of the SCSI bus, disable the terminators by removing the jumper from pins 15 and 16 of connector J2 (see Figure 6). If you install the drive on the end of the SCSI bus, enable termination by installing a jumper on pins 15 and 16 of connector J2.
34 Barracuda 9 Installation Guide, Rev. B N drives Terminator power There are three possible terminator power configurations for ST19171N drives (see Figure 7). You will not normally need to change this option and can leave the drive configured as it was shipped from the factory. Pin 1 J2 R T D MW P E T T E S E P D S P P Term. Power from Drive (default) Term. Power to SCSI Bus Term.
Barracuda 9 Installation Guide, Rev. B 35 N drives Other applicable jumper options Several other jumper options are available as illustrated. Drive with HDA up, PCB down, viewed from front J2 Pin 1 HDA Reserved Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) J6 Reserved L R R E E EA A A D S S 2 1 0 Reserved 11 Remote LED 12 CATH Shipped with cover installed. Do not remove. Do not install jumpers on these four positions.
36 Barracuda 9 Installation Guide, Rev. B W/WD drives Setting the SCSI W/WD ID jumpers drives section Use the J6 jumper block to set the SCSI ID (Figure 9). To change the SCSI ID, install jumpers on the appropriate pins as shown in the illustration. Optional connections to switching circuits in host equipment are provided on J1 auxiliary to set the SCSI ID (see Figure 10).
Barracuda 9 Installation Guide, Rev.
38 Barracuda 9 Installation Guide, Rev. B W/WD drives Terminating the drive ST19171W drives are terminated with permanently mounted IC active terminators. If you install one of these drives and it is not on the end of the SCSI bus, disable the terminators by removing the jumper from pins 15 and 16 of connector J2. If you install the drive on the end of the SCSI bus, enable termination by installing a jumper on pins 15 and 16 of connector J2 (see Figure 11). Note.
Barracuda 9 Installation Guide, Rev. B 39 W/WD drives Terminator power There are three possible terminator power configurations for ST19171W drives (see Figure 12). You will not normally need to change this option and can leave the drive configured as it was shipped from the factory. There are two possible terminator power configurations for ST19171WD drives (see Figure 12). Pin 1 J2 ST19171W Term. Power from Drive (default) R T D MW P E T T E S E P D S P P Term. Power to SCSI Bus Term.
40 Barracuda 9 Installation Guide, Rev. B W/WD drives Other applicable jumper options Other option jumpers are available as illustrated below. Drive with HDA up, PCB down, viewed from front J2 Pin 1 HDA Reserved Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) J6 Reserved L R R E E EA A A D S S 2 1 0 Reserved 11 Remote LED 12 CATH Shipped with cover installed. Do not remove. Do not install jumpers on these four positions.
Barracuda 9 Installation Guide, Rev. B 41 WC/DC drives Setting the SCSIWC/DC ID jumpers drives section The SCSI ID for WC and DC drives is normally set over the SCSI bus by the host system using connector contacts 39 (ID0), 40 (ID2), 79 (ID1), and 80 (ID3). Terminating the drive ST19171WC and ST19171DC drives do not have internal terminators or any other way of adding internal termination to the drive. You must provide external termination to these drives when termination is required.
42 Barracuda 9 Installation Guide, Rev. B WC/DC drives Applicable jumper options Option jumpers are available as illustrated below. Pin 1 J2 R Delay Motor Start option The host system has complete control over motor start functions. Do not install a jumper on these pins. RR R E D MW P E E E S S E P D S S S Enable Motor Start option The host system has complete control over motor start functions. Do not install a jumper on these pins.
Seagate Technology, Inc. 920 Disc Drive, Scotts Valley, CA 95066-4544, USA Publication Number: 83329020, Rev.
