Product manual
30 Barracuda 9 Product Manual, Rev. C
6.5 Mechanical specifications
The following nominal dimensions are exclusive of the decorative front panel accessory. However, dimensions
of the front panel are shown in the figure below. Refer to Figures 6, 7, and 8 for detailed mounting configuration
dimensions. See Section 8.4, “Drive mounting.”
Figure 6. Mounting configuration dimensions for “N” models
Typical Maximum
Height: 1.62 in 41.1 mm 1.654 in 42.0 mm
Width: 4.00 in 101.6 mm 4.01 in 101.9 mm
Depth: 5.75 in 146.05 mm 5.787 in 147 mm
Weight: 2.3 pounds 1.04 kilograms – –
A
P
N
F
.050 in. (1.27mm)
minimum clearance
R
D
[5] T
G
E
C
M
L
[3]
[1]
H
S
K
J
[4]
[2]
[9]
Inches Millimeters
5.750
4.000
1.640
0.625
4.000
0.250
2.375
3.750
2.375
1.750
0.181
0.340
0.190
0.015
1.720
4.100
0.143
0.260
0.030
0.405
2.265
146.05
101.60
41.66
15.87
101.60
6.35
60.32
95.25
60.32
44.45
4.60
8.64
4.83
0.381
43.69
104.14
3.63
6.60
0.76
10.28
57.53
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
T
U
V
W
X
0.010
0.010
0.020
0.020
0.010
0.005
0.010
0.010
0.010
0.020
0.015
0.015
0.010
0.010
0.010
±
±
±
±
±
±
±
±
±
±
±
±
±
max
±
±
.25
.25
.51
.50
.25
.13
.25
.25
.25
.50
.38
.38
.25
.25
.25
±
±
±
±
±
±
±
±
±
±
±
±
±
max
±
±
B
U [7]
[7] V
J2
J6 LED
X
W [6]
[8] [8]
Mounting holes three on each side, 6-32 UNC. Max screw length into
side of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb
(.675 NM) max with minimum thread engagement of 0.12 in. (3.05 mm).
Mounting holes four on bottom, 6-32 UNC. Max screw length into
bottom of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb
(.675 NM) max with minimum thread engagement of 0.12 in. (3.05 mm).
Power and interface connections.
Decorative front panel.
HDA mounting hole to centerline of Pin 1 of power connector.
HDA mounting hole to centerline of Pin 1 of J6. Pin ends on J6 are
nominally flush with end of drive.
HDA mounting hole to centerline of Pin 1 of J2.
Dimensions to Pin 1 of each connector are nominal values.
HDA mounting hole to centerline of LED lens.
Notes:
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]