................................................. Cheetah 10K.6 FC Disc Drive ................................................. ST3146807FC ................................................. ST373307FC ................................................. ST336607FC ................................................. Product Manual, Volume 1 .................................................
................................................. Cheetah 10K.6 FC Disc Drive ................................................. ST3146807FC ................................................. ST373307FC ................................................. ST336607FC ................................................. Product Manual, Volume 1 .................................................
© 2002 Seagate Technology LLC All rights reserved June 2002 Publication number: 100195490, Rev. B Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. Cheetah, SeaFAX, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications.
Revision status summary sheet Revision Date Writer/Engineer Sheets Affected A B 06/18/2002 06/26/2002 K. Schweiss/B. Hohn K. Schweiss/B. Hohn 1/1, v-viii, 1-72 19 Notice. Product Manual 100195490 is Volume 1 of a two volume document with the Fibre Channel Interface information in the Fibre Channel Interface Manual, part number 77767496. If you need the Fibre Channel Interface information, order the Fibre Channel Interface Manual, part number 77767496.
Cheetah 10K.6 FC Product Manual, Rev. B v Contents 1.0 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Applicable standards and reference documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.
vi Cheetah 10K.6 FC Product Manual, Rev. B 6.4 6.3.4 Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 6.3.5 Air cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 6.3.6 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 6.3.7 Electromagnetic susceptibility . . . . . . . . . . . . . . . . . . .
Cheetah 10K.6 FC Product Manual, Rev. B vii List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Cheetah 10K.6 FC family disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Cheetah 10K.6 FC disc drive . . . . . . . . . . . . . . .
Cheetah 10K.6 FC Product Manual, Rev. B 1.0 1 Scope This manual describes Seagate Technology® LLC, Cheetah® 10K.6 FC (Fibre Channel) disc drives. Cheetah 10K.6 FC drives support the Fibre Channel Arbitrated Loop and SCSI Fibre Channel Protocol specifications to the extent described in this manual. The Fibre Channel Interface Manual (part number 77767496) describes the general Fibre Channel Arbitrated Loop characteristics of this and other Seagate Fibre Channel drives. Figure 1. Cheetah 10K.
2 Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev. B 2.0 3 Applicable standards and reference documentation The drive has been developed as a system peripheral to the highest standards of design and construction. The drive depends upon its host equipment to provide adequate power and environment in order to achieve optimum performance and compliance with applicable industry and governmental regulations.
4 Cheetah 10K.6 FC Product Manual, Rev. B Australian C-Tick If this model has the C-Tick Marking it complies with the Australia/New Zealand Standard AS/NZS3548 1995 and meets the Electromagnetic Compatibility (EMC) Framework requirements of Australia’s Spectrum Management Agency (SMA).
Cheetah 10K.6 FC Product Manual, Rev. B 3.0 5 General description Cheetah 10K.6 FC drives combine giant magnetoresistive (GMR) heads, partial response/maximum likelihood (PRML) read channel electronics, embedded servo technology, and a Fibre Channel interface to provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers. Cheetah 10K.
6 Cheetah 10K.6 FC Product Manual, Rev. B 3.1 Standard features Cheetah 10K.
Cheetah 10K.6 FC Product Manual, Rev. B 7 • Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.) • Dithering 3.5 Unformatted and formatted capacities Formatted capacity depends on the spare reallocation sectors scheme selected, the number of data tracks per sparing zone, and the number of alternate sectors (LBAs) per sparing zone. The following table shows the standard OEM model capacity: ST3146807FC ST373307FC ST336607FC Formatted Unformatted 11177330h (146.8) Gbytes 88BB998h (73.
8 Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev. B 4.0 9 Performance characteristics This section provides detailed information concerning performance-related characteristics and features of Cheetah 10K.6 FC drives. 4.1 Internal drive characteristics Drive capacity Read/write data heads Bytes per track Bytes per surface Tracks per surface (total) Tracks per inch Peak bits per inch Internal data rate Disc rotation speed Avg rotational latency ST3146807FC...........ST373307FC .......... ST336607FC 146.8 .........
10 4.2.3 Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev. B 11 The buffer can be divided into logical segments (using Mode Select Page 08h, byte 13) from which data is read and to which data is written. The drive keeps track of the logical block addresses of the data stored in each segment of the buffer. If the cache is enabled (see RCD bit in the Fibre Channel Interface Manual ), data requested by the host with a read command is retrieved from the buffer, if possible, before any disc access is initiated.
12 Cheetah 10K.6 FC Product Manual, Rev. B was written there at the beginning of the operation; however, the drive does not overwrite data that has not yet been written to the medium. If write caching is enabled (WCE=1), then the drive may return Good status on a write command after the data has been transferred into the cache, but before the data has been written to the medium.
Cheetah 10K.6 FC Product Manual, Rev. B 5.0 13 Reliability specifications The following reliability specifications assume correct host and drive operational interface, including all interface timings, power supply voltages, environmental requirements and drive mounting constraints Seek error rate Read Error Rates1 Recovered Data Unrecovered Data Miscorrected Data Interface error rate MTBF Service life Preventive maintenance 1.
14 Cheetah 10K.6 FC Product Manual, Rev. B Sense Key. This is an unrecoverable seek error. Unrecoverable seek errors are classified as failures for MTBF calculations. Refer to the Fibre Channel Interface Manual, part number 77767496, for Request Sense information. 5.2 Reliability and service You can enhance the reliability of Cheetah 10K.6 FC disc drives by ensuring that the drive receives adequate cooling. Section 6.
Cheetah 10K.6 FC Product Manual, Rev. B 5.2.6 15 Hot plugging the drive Inserting and removing the drive on the FC-AL will interrupt loop operation. The interruption occurs when the receiver of the next device in the loop must synchronize to a different input signal. FC error detection mechanisms, character sync, running disparity, word sync, and CRC are able to detect any error. Recovery is initiated based on the type of error.
16 Cheetah 10K.6 FC Product Manual, Rev. B bus. The process of measuring off-line attribute data and saving data to the disc is uninterruptable. The maximum on-line only processing delay is summarized below: Maximum processing delay S.M.A.R.T. delay times On-line only delay DEXCPT = 0, PERF = 1 Fully-enabled delay DEXCPT = 0, PERF = 0 50 milliseconds 300 milliseconds Reporting control Reporting is controlled by the MRIE bits in the Informational Exceptions Control mode page (1Ch).
Cheetah 10K.6 FC Product Manual, Rev. B 17 The following conditions are considered DST failure conditions: • • • • Seek error after retries are exhausted Track-follow error after retries are exhausted Read error after retries are exhausted Write error after retries are exhausted Recovered errors will not be reported as diagnostic failures. 5.2.8.2 Implementation This section provides all of the information necessary to implement the DST function on this drive. 5.2.8.2.
18 5.2.8.2.4 Cheetah 10K.6 FC Product Manual, Rev. B Log page entries When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created by inserting a new self-test parameter block at the beginning of the self-test results log parameter section of the log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 parameter blocks in the log page.
Cheetah 10K.6 FC Product Manual, Rev. B 6.0 19 Physical/electrical specifications This section provides information relating to the physical and electrical characteristics of the drive. 6.1 AC power requirements None. 6.2 DC power requirements The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.
20 Cheetah 10K.6 FC Product Manual, Rev. B 3. Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device. 4. Parameters, other than spindle start, are measured after a 10-minute warm up. 5. No terminator power. 6.2.
Cheetah 10K.6 FC Product Manual, Rev. B Figure 4. Typical ST373307FC drive +12V current profile Figure 5.
22 Cheetah 10K.6 FC Product Manual, Rev. B Figures 6, 7 and 8 identify the drive +5V current profiles for each model ST3146807FC, ST3733307FC and ST336607FC, respectively. The current during the various times is as shown: T0 T1 T2 T3 Power is applied to the drive. Controller self-tests are performed. Spindle begins to accelerate under current limiting after performing internal diagnostics. Spindle is up to speed and the Head-Arm restraint is unlocked. Figure 6.
Cheetah 10K.6 FC Product Manual, Rev. B Figure 7. Typical ST373307FC drive +5V current profile Figure 8.
24 Cheetah 10K.6 FC Product Manual, Rev. B 6.3 Power dissipation ST3146807FC Typical power dissipation under idle conditions is 10.72 watts (37.3 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 9). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.
Cheetah 10K.6 FC Product Manual, Rev. B 25 ST336607FC Typical power dissipation under idle conditions is 7.89 watts (26.9 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 9). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123.
26 Cheetah 10K.6 FC Product Manual, Rev. B b. Non-operating –40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. HDA Temp. Check Point .5" Figure 13. Location of the HDA Temperature check point 6.3.2 Relative humidity The values below assume that no condensation on the drive occurs. a.
Cheetah 10K.6 FC Product Manual, Rev. B 27 b. Operating—abnormal Equipment, as installed for normal operation, does not incur physical damage while subjected to intermittent shock not exceeding 40 Gs at a maximum duration of 11 msec (half sinewave). Shock occurring at abnormal levels may promote degraded operational performance during the abnormal shock period. Specified operational performance will continue when normal operating shock levels resume. Shock may be applied in the X, Y, or Z axis.
28 Cheetah 10K.6 FC Product Manual, Rev. B Z X Y X Figure 14.
Cheetah 10K.6 FC Product Manual, Rev. B 6.3.4.2 29 Vibration a. Operating - normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 5-500 Hz @ 1.0 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Operating normal translational random flat profile 10 - 400 Hz 0.4 GRMS b.
30 6.4 Cheetah 10K.6 FC Product Manual, Rev. B Mechanical specifications The following nominal dimensions are exclusive of the decorative front panel accessory. However, dimensions of the front panel are shown in figure below. Refer to Figure 15 for detailed mounting configuration dimensions. See Section 8.5, “Drive mounting.” Height: Width: Depth: Weight: 1.000 in 4.000 in 5.75 in 1.62 pounds 25.4 mm 101.6 mm 146.05 mm 0.
Cheetah 10K.6 FC Product Manual, Rev. B 7.0 31 Defect and error management The drive, as delivered, complies with this product manual. The read error rates and specified storage capacities are not dependent upon use of defect management routines by the host (initiator). Defect and error management in the SCSI protocol involves the drive internal defect/error management and FC-AL system error considerations (errors in communications between the initiator and the drive).
32 Cheetah 10K.6 FC Product Manual, Rev. B When the RC bit is one, reallocations are disabled even if the ARRE or AWRE bits are one. The drive will still perform data recovery actions within the limits defined by the Read Retry Count, Write Retry Count, and Recovery Time Limit parameters. However, the drive does not report any unrecovered errors.
Cheetah 10K.6 FC Product Manual, Rev. B 8.0 33 Installation Cheetah 10K.6 FC disc drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive. Simply plug the drive into the host’s 40-pin Fibre Channel backpanel connector (FCSCA)—no cables are required. See Section 9.5 for additional information about this connector. Use the FC-AL interface to select drive ID and all option configurations for devices on the loop.
34 Cheetah 10K.6 FC Product Manual, Rev. B Drive Front Pin 1 J6 Reserved Port A Bypass LED [1] Port B Bypass LED [1] Fault LED [1] Reserved Active LED [2] Reserved +5V Active LED [1] Ground [3] Figure 17. 8.2.1 [1] The drive has a 1.2K ohm resistor in series with this LED driver. Tie the minus side of an external high-efficiency LED (i.e., 2ma) to this pin. Connect the plus side of the LED to +5V. [2] An external current-limiting resistor is required when connecting an LED to this pin.
Cheetah 10K.6 FC Product Manual, Rev. B 35 created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources within the rack, cabinet, or drawer environment. If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 18.
36 8.6 Cheetah 10K.6 FC Product Manual, Rev. B Grounding Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electrically isolating shock mounts.
Cheetah 10K.6 FC Product Manual, Rev. B 9.0 37 Interface requirements This section partially describes the interface requirements as implemented on Cheetah 10K.6 FC drives. Additional information is provided in the Fibre Channel Interface Manual (part number 77767496). 9.1 FC-AL features This section lists the Fibre Channel-specific features supported by Cheetah 10K.6 FC drives. 9.1.1 Fibre Channel link service frames Table 3 lists the link services supported by Cheetah 10K.6 FC drives.
38 Cheetah 10K.6 FC Product Manual, Rev. B 9.1.4 Fibre Channel port login Table 6 identifies the required content of the N_Port Login (PLOGI) payload from an initiator.
Cheetah 10K.6 FC Product Manual, Rev. B 9.1.5 39 Fibre Channel port login accept Table 7 identifies the N_Port Login access payload values.
40 Cheetah 10K.6 FC Product Manual, Rev. B 9.1.8 Fibre Channel fabric login Table 10 lists the fabric login payload from the drive.
Cheetah 10K.6 FC Product Manual, Rev. B 9.1.9 41 Fibre Channel fabric accept login Table 10 lists the required content of the Fabric Login Accept (ACC) payload from the fabric.
42 Cheetah 10K.6 FC Product Manual, Rev. B 9.1.10 Fibre Channel Arbitrated Loop options Table 12 lists the FC-AL options supported by Cheetah 10K.6 FC drives. Table 12: FC-AL options supported Option Supported OPEN Half Duplex Accepted from another device. OPEN Full Duplex Sent to open another device. Accepted from another device. Private Loop Yes Public Loop Yes Old Port State No Loop Position Yes Loop Position Report Yes 9.2 Dual port support Cheetah 10K.
Cheetah 10K.6 FC Product Manual, Rev. B 9.3 SCSI commands supported Table 13 lists the SCSI commands supported by Cheetah 10K.6 FC drives.
44 Table 13: Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev.
46 Cheetah 10K.6 FC Product Manual, Rev. B [1] Cheetah 10K.6 FC drives can format to any multiple of four bytes per logical block in the range 512 to 704 bytes. [2] Warning. Power loss during flash programming can result in firmware corruption. This usually makes the drive inoperable. [3] Reference Mode Sense command 1Ah for mode pages supported. [4] Y = Yes. Command is supported. N = No. Command is not supported. A = Support is available on special request.
Cheetah 10K.6 FC Product Manual, Rev. B 9.3.1 47 Inquiry data Table 14 lists the Inquiry command data that the drive should return to the initiator per the format given in the Fibre Channel Interface Manual. Table 14: Cheetah 10K.
48 Cheetah 10K.6 FC Product Manual, Rev. B 3. Current values Current values are volatile values being used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, Target Reset, or LIP Reset. 4.
Cheetah 10K.6 FC Product Manual, Rev.
50 Table 16: Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev.
52 Cheetah 10K.6 FC Product Manual, Rev. B 9.4 Miscellaneous operating features and conditions Table 18 lists various features and conditions. A “Y” in the support column indicates the feature or condition is supported. An “N” in the support column indicates the feature or condition is not supported.
Cheetah 10K.6 FC Product Manual, Rev. B 9.5 53 FC-AL physical interface Figure 19 shows the location of the J1 Fibre Channel single connection attachment (FC-SCA) and the J6 connector. Figure 21 provides the dimensions of the FC-SCA. Figure 22 provides the dimensions of the J6 connector. Details of the physical, electrical, and logical characteristics are provided within this section. The operational aspects of Seagate’s Fibre Channel drives are provided in the Fibre Channel Interface Manual.
54 9.5.2 Cheetah 10K.6 FC Product Manual, Rev. B Connector requirements Recommended mating SCA part number: Part description Positions Part number Features AMP Vertical (SCA sequence) 40 787317-1 With polarization Berg 40 71781 With polarization Methode 40 512-220-91-101N With polarization Molex 40 717431040 With polarization The FC-AL SCA device connector is illustrated in Figure 21. The J6 connector is illustrated in Figure 22. 1.618 ± .003 in (41.1 ± 0.
Cheetah 10K.6 FC Product Manual, Rev. B 9.5.3 55 Electrical description Fibre Channel drives use the FC-SCA connector for: • • • • • DC power FC-AL interface Drive select (device identification) Option selection Enclosure Services interface This 40-pin connector is designed to plug directly into a backpanel. External cables are not required. 9.5.4 Pin descriptions This section provides a pin-out of the FC-SCA and a description of the functions provided by the pins.
56 9.5.5 Cheetah 10K.6 FC Product Manual, Rev. B FC-AL transmitters and receivers A typical FC-AL differential copper transmitter and receiver pair is shown in Figure 23. The receiver is required to provide the AC coupling to eliminate ground shift noise. 68 .01 TX Transmitter TY RX 150 Differential Transfer Medium 9.5.6 Receiver RY 68 .01 150 Figure 23. 150 FC-AL transmitters and receivers Power Power is supplied through the FC-SCA with support for +5 volts and +12 volts.
Cheetah 10K.6 FC Product Manual, Rev. B 57 The Active LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +5 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. 9.5.9 Enable port bypass signals The – Enable Bypass Port A (– EN BYP Port A) and – Enable Bypass Port B (– EN BYP Port B) signals control the port bypass circuits (PBC) located external to the disc drive.
58 9.5.11.1 Cheetah 10K.6 FC Product Manual, Rev. B Parallel Enclosure Services Interface (ESI) The parallel ESI line is an output from the drive. This line provides the enclosure with an indication of the present function of the SEL lines. A high level, the default state, indicates the drive requires address information on the SEL lines. A low level indicates the drive is attempting an ESI transfer. The enclosure may not support ESI on any or all drive locations. It may only support the address function.
Cheetah 10K.6 FC Product Manual, Rev.
60 9.5.12 Cheetah 10K.6 FC Product Manual, Rev. B Device control codes The drive inputs a Device Control Code on the DEV_CTRL_CODE lines at power up to determine the link rate on the Fibre Channel ports. Both ports run at the same rate. If the backpanel does not connect to these lines, the drive has 10K ohm pull up resistors that default the device control code to 7 (1.0625 GHz). Table 24 lists the supported codes.
Cheetah 10K.6 FC Product Manual, Rev. B 9.6.3 61 Differential PECL output The serial PECL output signal voltage characteristics are provided in Table 27. The outputs are not AC coupled in order to deliver maximum signal without rise and fall time degradation. You must AC couple the receiver to isolate potentially different DC characteristics of the outputs and the receiver.
62 Table 29: Cheetah 10K.6 FC Product Manual, Rev. B Eye diagram data values Link rate 1 GHz 2 GHz Bit time 941 ps 470 ps XMIT eye 725 ps min. 315 ps min.
Cheetah 10K.6 FC Product Manual, Rev. B 10.0 63 Seagate Technology support services Online Services Internet www.seagate.com for information about Seagate products and services. Worldwide support is available 24 hours daily by e-mail for your disc or tape questions. Presales Support: Disc: www.seagate.com/support/email/email_presales.html or DiscPresales@Seagate.com. Tape: www.seagate.com/support/email/email_tape_presales.html or Tape_Sales_Support@Seagate.com. Technical Support: Disc: www.seagate.
64 Cheetah 10K.6 FC Product Manual, Rev. B Customer Service (CSO) Warranty Service Seagate offers worldwide customer support for Seagate drives. Seagate direct OEM, Distribution and System Integrator customers should contact their Seagate service center representative for warranty information. Other customers should contact their place of purchase. Authorized Service Centers If you live outside the US, you can contact an Authorized Service Center for service.
Cheetah 10K.6 FC Product Manual, Rev. B Spain Sweden Switzerland Turkey United Kingdom 65 900-98 31 24 0 207 90 073 0 800-83 84 11 00 800-31 92 91 40 0 800-783 5177 FAX Services—All European Countries Presales/Technical Support/Warranty Service 31-20-653-3513 Africa/Middle East Support Services For presales, technical support, warranty service and FAX services in Africa and the Middle East, dial our European call center at +31-20-316-7222 from 8:30 A.M. to 5:00 P.M.
66 Cheetah 10K.6 FC Product Manual, Rev.
Cheetah 10K.6 FC Product Manual, Rev.
68 data transfer rate 10 data valid eye 61 Date code page command 43 DC power 55 requirements 19 defect and error management 31 deferred error handling 52 description 5 DEV_CTRL_CODE 60 device behavior page command 43 device control code values 60 device control codes 60 device identification page command 43 device selection IDs 33 devices 33 differential PECL input 61 dimensions 30 Disable page out command 44 disc rotation speed 9 Disconnect/reconnect control (page 02h) command 43 Download microcode and sa
Cheetah 10K.6 FC Product Manual, Rev.
70 Busy 52 Check condition 52 Condition met/good 52 Good 52 Intermediate/condition met/good 52 Intermediate/good 52 Reservation conflict 52 Task set full 52 miscorrected media data 13 Mode select (10) command 45 command 43 Mode sense (10) command 45 command 43 data, table 47, 49, 50, 51 monitoring state 15 motor start controls 57 option 10 mounting 35 holes 35 orientations 34 mounting configuration 30 mounting configuration dimensions 30 MTBF 13, 14, 25 defined 14 N N_Port Login (PLOGI) 37 payload 38 paylo
Cheetah 10K.6 FC Product Manual, Rev.
72 Supported diagnostics pages command 43, 44 surface stiffness allowable for non-flat surface 35 switches 33 Synchronize cache command 44 synchronized spindle operation 52 system chassis 36 T target reset function 37 task management functions 37 Abort task set 37 Clear ACA 37 Clear task set 37 Target reset 37 terminate task 37 task management response codes 37 Function complete 00 37 Function not supported 05 37 Function reject 04 37 task set full status 52 technical support services 63 temperature 25, 34
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100195490, Rev.