Product Manual Constellation ES Serial ATA ® ST32000644NS ST31000524NS ST3500514NS 100516232 Rev.
Revision history Revision Rev. A Rev. B Rev. C Rev. D Rev. E Rev. F Date 08/26/09 09/23/09 01/11/10 04/21/10 06/16/10 08/02/10 Sheets affected or comments Initial release. 3-4, 6 and 13. 4, 13, 16 and 20. 1, 5, 9-11,14-15 & 17-18. 5 & 17-18. 6 & 31. © 2010 Seagate Technology LLC. All rights reserved. Publication number: 100516232, Rev. F, August 2010 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents 1.0 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii Constellation ES Serial ATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . .
1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: Presales & Technical support Global Support Services telephone numbers & business hours Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.
2.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Constellation® ES Serial ATA model drives: ST32000644NS ST31000524NS ST3500514NS These drives provide the following key features: • 7200 RPM spindle speed. • PowerChoice™ for selectable power savings • Top Cover Attached motor for excellent vibration tolerance • High instantaneous (burst) data-transfer rates (up to 300MB per second).
2.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels.
3.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST32000644NS 3.1 ST31000524NS ST3500514NS Specification summary tables The specifications listed in the following tables are for quick reference.
Drive specification ST32000644NS ST31000524NS ST3500514NS Power-on to ready (sec max) 15 10 7 Standby to ready (sec max) 15 10 7 Track-to-track seek time (ms typical) 0.5 read 0.8 write Average seek, read (ms typical) <8.5 Average seek, write (ms typical) <9.5 Startup current (typical) 12V (peak) 2.8A 2.
3.2 Formatted capacity Model Formatted capacity* Guaranteed sectors ST32000644NS 2TB 3,907,029,168 ST31000524NS 1TB 1,953,525,168 ST3500514NS 500GB Bytes per sector 512 976,773,168 *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 3.2.
3.5 Physical characteristics Maximum height 26.1mm (1.028 in) Maximum width 101.6mm (4.000 +/- 0.010 in) Maximum length 146.99mm (5.787 in) Max weight ST32000644NS 710g (1.565 lb) ST31000524NS 640g (1.411 lb) ST3500514NS 610g (1.345 lb) Cache buffer 3.6 ST32000644NS 64MB (64,768KB) ST31000524NS and ST3500514NS 32MB (32,768KB) Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics.
3.8 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 3 on page 24. 3.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
Table 2: 2000GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.26 0.42 6.38 0.27 0.42 6.39 Idle_A 0.13 0.35 4.83 0.14 0.42 5.70 Idle_B 0.13 0.36 5.01 0.14 0.36 5.00 Idle_C 0.13 0.22 3.26 0.14 0.22 3.27 Standby 0.09 0.01 0.51 0.09 0.01 0.53 Idle_A (Active) 0.86 1.66 24.22 0.98 0.90 15.70 Idle_B (Active) 0.76 1.72 24.47 0.74 1.64 23.
Table 3: 1000GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.27 0.27 4.59 0.27 0.27 4.61 Idle_A 0.14 0.27 3.86 0.15 0.27 3.99 Idle_B 0.14 0.23 3.53 0.15 0.23 3.56 Idle_C 0.14 0.08 1.70 0.15 0.08 1.73 Standby 0.09 0.01 0.54 0.10 0.01 0.57 0.86 0.98 16.06 0.86 1.06 17.
Table 4: 500GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.26 0.20 3.71 0.28 0.20 3.74 Idle_A 0.13 0.21 3.13 0.14 0.21 3.17 Idle_B 0.13 0.18 2.82 0.14 0.18 2.85 Idle_C 0.13 0.07 1.50 0.14 0.07 1.52 Standby 0.09 0.01 0.53 0.09 0.01 0.55 Idle_A (Active) 0.84 0.52 10.44 0.84 0.54 10.68 Idle_B (Active) 0.70 1.11 16.81 0.80 1.13 17.
3.8.1.1 12 Typical current profiles Constellation ES Serial ATA Product Manual, Rev.
Figure 1. Typical 5V startup and operation current profile Figure 2. Typical 12V startup and operation current profile 3.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 V line or an equivalent 15-ohm resistive load on the +5V line. • Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave injected noise at up to 10MHz.
3.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
3.8.4.1 Extended Power Conditions - PowerChoiceTM Utilizing the load/unload architecture a programmable power management interface is provided to tailor systems for reduced power consumption and performance requirements. The table below lists the supported power conditions available in PowerChoice.
S.M.A.R.T. Read Data Reports • Attribute 192 - Emergency Retract Count • Attribute 193 - Load/Unload Cycle Count PowerChoice Manufacture Default Power Condition Timer Values Default power condition timer values have been established to assure product reliability and data integrity. A minimum timer value threshold of two minutes ensures the appropriate amount of background drive maintenance activities occur.
3.9 Environmental limits Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C). 3.9.1 Temperature a. Operating To obtain optimal performance, drives should be run at nominal case temperatures.
3.9.4.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 70 Gs (read) and 40 Gs (write) based on half-sine shock pulses of 2ms. Shocks should not be repeated more than two times per second. 3.9.4.
3.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.
3.13 Reliability 3.13.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of 0.73% (MTBF of 1.2 million hours) when operated nominal power and typical case temperatures of 40°C. Operation at temperatures outside the specifications in Section 3.9 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics that are not relevant to individual units.
Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
3.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 3.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.
4.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 4.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
4.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices. 4.
4.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 in (0.76mm) around the entire perimeter of the drive for cooling. • Use only 6-32 UNC mounting screws. • The screws should be inserted no more than 0.150 in (3.81mm) into the bottom or side mounting holes.
5.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 5.
5.2 Serial ATA device plug connector pin definitions Table 7 summarizes the signals on the Serial ATA interface and power connectors. Table 7: Segment Signal Serial ATA connector pin definitions Pin Function Definition S1 Ground 2nd mate S2 A+ Differential signal pair A from Phy S3 A- S4 Ground 2nd mate S5 B- Differential signal pair B from Phy S6 B+ S7 Ground 2nd mate Key and spacing separate signal and power segments Power P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.
5.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 35.for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Security Freeze F5H Security Set Password F1H Security Unlock F2H Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable/Disable Autosave B0H / D2H S.M.A.R.T.
5.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 8 on page 28. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 3.0 on page 4 for default parameter settings.
Word Description Value 60–61 Total number of user-addressable LBA sectors available (see Section 3.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field and the actual number of user-addressable LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature.
Word Description Value 108–111 The mandatory value of the world wide name (WWN) for the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support. Each drive will have a unique value. 112–127 ATA-reserved 0000H 128 Security status 0001H 129–159 Seagate-reserved xxxxH 160–254 ATA-reserved 0000H 255 Integrity word xxA5H Note. See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.
Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported. 6 Ultra DMA mode 6 is supported. 8 Ultra DMA mode 0 is currently active. 9 Ultra DMA mode 1 is currently active. 10 Ultra DMA mode 2 is currently active. 11 Ultra DMA mode 3 is currently active. 12 Ultra DMA mode 4 is currently active.
5.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
5.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
36 Constellation ES Serial ATA Product Manual, Rev.
Index A ACA 21 acoustics 19 Active 14 Active mode 14 actuator arm 8 Agency certification 20 air flow 17 altitude 17 ambient 17 ambient temperature 7, 8, 17 Annualized Failure Rate (AFR) 20 areal density 2, 6 ATA commands 28 Australia/New Zealand Standard AS/NZ CISPR22 21 Australian Communication Authority (ACA) 21 Australian C-Tick 21 average idle current 9, 10, 11 Average latency 7 Average seek time 7 B BPI 6 buffer 7 C cables and connectors 24 cache 7 capacity 6 case temperature 17 CE mark 20 certificat
Identify Device 28 Identify Device command 30 Idle 14, 28 Idle Immediate 28 Idle mode 8, 14 Information Technology Equipment (ITE) 20 Initialize Device Parameters 28 Input noise ripple 13 input voltage 8 interface 6, 26 interference 21 internal data-transfer rate OD 6 is 7 ISO document 7779 19 ITE 20 K KCC 21 Korean Communications Commission 21 Korean RRL 21 L latency 7 latency time 8 LBA mode 6 length 7 logical geometry 6 M maintenance 20 master/slave 3 maximum start current 9, 10, 11 mounting 25 mounti
S T S.M.A.R.T. Disable Operations 29 S.M.A.R.T. Enable Operations 29 S.M.A.R.T. Enable/Disable Autosave 29 S.M.A.R.T. Execute Offline 29 S.M.A.R.T. implementation 28 S.M.A.R.T. Read Attribute Thresholds 29 S.M.A.R.T. Read Data 29 S.M.A.R.T. Read Log Sector 29 S.M.A.R.T. Return Status 29 S.M.A.R.T. Save Attribute Values 29 S.M.A.R.T.
40 Constellation ES Serial ATA Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100516232, Rev.
