Product Manual DiamondMax 21 PATA STM3320820A STM3200820A STM3300620A STM3160215A STM3250620A STM380215A STM3250820A 100451230 Rev.
Revision status summary sheet Revision Date Sheets Affected Rev. A Rev. B 11/16/06 09/21/07 Initial Release. Front cover, 1, 3, 8-13, 16-18, 22 and 33. Copyright © 2006, 2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100451230, Rev. B September 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . .
ii DiamondMax 21 PATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master/slave jumper settings . . . . . . . . . . . . . .
iv DiamondMax 21 PATA Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Maxtor® DiamondMax® 21 PATA model drives: STM3320820A STM3250620A STM3200820A STM3300620A STM3250820A STM3160215A STM380215A These drives provide the following key features: • 7,200-RPM spindle speed • High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.
2 DiamondMax 21 PATA Product Manual, Rev.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: STM3320820A STM3250620A STM3200820A STM3300620A STM3250820A STM3160215A 2.1 STM380215A Specification summary tables The specifications listed in the following tables are for quick reference.
Table 1: 4 Drive specifications summary for the 320 and 300 Gbyte models Drive specification STM3320820A STM3300620A Formatted Gbytes (512 bytes/sector)* 320 300 Guaranteed sectors 625,142,448 586,072,368 Heads 4 3 Discs 2 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 781 kbits/in max Track density 145 ktrakcs/in avg. Areal density 114.
Drive specification STM3320820A Vibration, operating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G STM3300620A Drive acoustics, sound power (Bels) Idle** 2.7 (typical) 3.0 (max) 2.5 (typical) 2.8 (max) Quiet seek 3.0 (typical) 3.4 (max) 3.0 (typical) 3.1 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.
Table 2: 6 Drive specifications summary for 250 and 200 Gbyte models Drive specification STM3250620A STM3250820A STM3200820A Formatted Gbytes (512 bytes/sector)* 250 200 Guaranteed sectors 488,397,168 390,721,968 Heads 3 Discs 2 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 813 kbits/in max Track density 145 ktracks/in avg. Areal density 114.
Drive specification STM3250620A STM3250820A Vibration, operating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G STM3200820A Drive acoustics, sound power (Bels) Idle** 2.5 (typical) 2.8 (max) Quiet seek 3.0 (typical) 3.1 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 3 years on distribution units.
Table 3: 8 Drive specifications summary for the 160 and 80 Gbyte model Drive specification STM3160215A STM380215A Formatted Gbytes (512 bytes/sector)* 160 80 Guaranteed sectors 312,581,808 156,301,488 Heads 2 1 Discs 1 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 824 kbits/in max Track density 137.259 ktracks/in avg.
Drive specification STM3160215A Vibration, operating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement 22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G STM380215A Drive acoustics, sound power (Bels) Idle** 2.8 (typical) 3.0 (max) Quiet seek 3.0 (typical) 3.2 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 3 years on distribution units.
2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors STM3320820A 320 Gbytes 625,142,448 STM3300620A 300 Gbytes 586,072,368 250 Gbytes 488,397,168 STM3200820A 200 Gbytes 390,721,968 STM3160215A 160 Gbytes 312,581,808 STM380215A 80 Gbytes 156,301,488 STM3250620A STM3250820A Bytes per sector 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.
2.4 Recording and interface technology 320GB 300GB 250GB 200GB 160GB 813 781 824 Interface ATA Recording method Perpendicular Recording density, KBPI (kbits/inch max) 781 Track density, KTPI (ktracks/inch avg) 145 137.259 Areal density (Gbits/inch avg) 114.4 101 Spindle speed (RPM) (± 0.2%) 7,200 Internal data transfer rate (Mbits/sec max) 1,030 930 Sustained data transfer rate (Mbytes/sec max) 72 78 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) 2 2.
2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead.
2.8 Power specifications The drive receives DC power (+5V or +12V) through a four-pin standard drive power connector. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 13. Typical power measurements are based on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
2.8.1.1 Typical current profile Figure 1 Typical 5V startup and operation current profile Figure 2 Typical 12V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz.
2.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions. Recommended measurement locations are shown in See Figure 6 on page 27. Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters).
2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock 320GB - 200GB models These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 68 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.
2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.
2.
2.12 Reliability 2.12.1 Annualized Failure Rate (AFR and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of 0.34% (MTBF of 0.7 million hours) when operated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifications in Section 2.9 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics that are not relevant to individual units.
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather hole Do not cover or seal this hole. Figure 3 Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole.
3.3 Jumper settings 3.3.1 Master/slave configuration The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Drive as slave. Remove all jumpers.
3.3.3 Ultra ATA/100 cable An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4, and mode 5. This cable uses even-numbered conductors connected to the ground pins to improve signal integrity. Master Pin 1 Co Mo mpu the ter rbo ard Slave Figure 5 Note. 3.4 Note. If you are using a 40-pin, 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive, and the gray connector to the slave.
Notes: 1. Dimensions are shown in inches (mm). 2 Dimensions per SFF-8301 specification. 0.228 (5.79) 1.028 max (26.11) 2.83 (71.80) 3 x 0.25 0.010 (6.35 0.037) both sides 1.122 0.02 (28.5 0.51) 1.638 (41.61 0.01 0.25) 0.178 (4.27) 2.23 (56.56) 3.71 (94.35) 2 1.625 0.020 (41.28 0.51) 5.787 max (146.99) 1.75 0.01 (44.45 0.25) 4.0 0.01 (101.60 0.25) 4 x 6-32 UNC-2B 0.150 (3.81) max. fastener penetration. 3 threads minimum engagement.
28 DiamondMax 21 PATA Product Manual, Rev.
4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. You can use a daisy-chain cable to connect two drives to a single AT host bus.
4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T. commands” on page 36 for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Security Erase Unit F4H Security Freeze F5H Security Set Password F1H Security Unlock F2H Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep 99H or E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T.
4.1.2 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the Table 7 on page 30. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
Word Description Value 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes). Drives with capacities over 137 Gbytes will have 0FFFFFFFh in this field and the actual number of user-addressable LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature.
Word Description Value 129–159 Seagate-reserved xxxxH 160–254 ATA-reserved 0000H 255 Integrity word xxA5H Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data: Description (if bit is set to 1) 34 Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported.
4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.1.4 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
5.0 Maxtor support services Before contacting Maxtor Support, use the Hard Disk Information feature in MaxBlast to view the model number and serial number of your drive. These numbers can be used to get help from Maxtor Support, register your drive, and look up information on the Maxtor website. Please visit http://www.seagate.com/maxtor/ to obtain comprehensive support information, such as: • Warranty services Drive returns, warranty status, and limited warranty statement.
38 DiamondMax 21 PATA Product Manual, Rev.
Index A acoustics 18 Active mode 15 AFR 20 agency certification (regulatory) 20 altitude 16 ambient conditions 3 ambient temperature 12, 16 Annualized Failure Rate 20 Annualized Failure Rate (AFR) 20 areal density 1, 11 ATA interface 29 ATA-standard commands 30 Australian C-Tick 21 autodetection 1 average seek time 12 B BPI 11 breather filter hole precautions 24 burst 1 C cable 26 cable select 1 cable-select option 25 cache 1 case temperature 16 CE mark 20 certification 20 Check Power Mode 30 China RoHS d
Identify Device command 32 Idle 30 Idle and Standby timers 15 Idle Immediate 30 Idle mode 15 Idle mode power 13 IEC950 20 Information Technology Equipment 20 Initialize Device Parameters 30 interface 11, 29 interface signals 29 interference 21 internal data-transfer rate OD 11 ISO document 7779 18 J jumper settings 25 K Korean RRL 21 L LBA mode 10 length 11 logical geometry 10 M maintenance 20 master 25 master/slave 1 Master/slave configuration 25 maximum temperature 16 Mean Time Between Failures 20 mea
S.M.A.R.T. Enagle Operations 31 S.M.A.R.T. Execute Offline 31 S.M.A.R.T. Read Attribute Thresholds 31 S.M.A.R.T. Read Data 31 S.M.A.R.T. Read Log Sector 31 S.M.A.R.T. Return Status 31 S.M.A.R.T. Save Attribute Values 31 S.M.A.R.T.
42 DiamondMax 21 PATA Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100451230, Rev. B, Printed in U.S.A.
