Product Manual Lyrion Series CE-ATA ST760211CA ST730212CA 100441950 Rev.
Revision history Revision Rev. A Date 05/22/08 Sheets affected or comments Initial release. Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100441950, Rev. A May 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Drive care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . .
ii Lyrion CE-ATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Lyrion Series (CE-ATA interface) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Typical 3.3V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Location where tri-axial accelerometer will be placed on Lyrion Series drives . . . . . . . . . . . . 12 Drive axis definition for Lyrion Series drives . . . .
iv Lyrion CE-ATA Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® Lyrion®Series CE-ATA drives: • ST760211CA-60GB, ST730212CA-30GB disc drives with a CE-ATA interface. These drives provide the following key features. • 3,600-RPM spindle speed and a 2-Mbyte buffer combined for superior read/write performance. • Quiet operation. Fluid Dynamic Bearing (FDB) motor.
1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, noninfringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST760211CA and ST730212CA model drives. 2.1 Overview The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
Table 1: Specifications Drive specification ST760211CA Performance idle power (typical 3.3V) 0.68 W Low power idle power (typical 3.3V) 0.48 W Standby/Sleep power (typical 3.3V) 0.20 W Voltage tolerance (including noise) 3.
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector (logical) ST760211CA 60 Gbytes 117,210,240 512 ST730212CA 30 Gbytes 58,605,120 512 LBA mode addressing When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.
2.4 Recording and interface technology Technology Specification Interface CE-ATA Recording method Perpendicular Magnetic Recording Recording density BPI (bits/inch average) 1,025,000 Track density TPI (tracks/inch average) 165,000 Areal density (Gbits/inch2 average) 169 Spindle speed (RPM) (± 0.2%) 3,600 Internal data-transfer rate OD (Mbits/sec max) 350 Sustained data transfer rate OD @ 8bit/52MHz (Mbytes/sec) 24.5 Sustained data transfer rate OD @ 8bit/26MHz (Mbytes/sec) 18.
2.7 Power specifications The drive receives DC power (+3.3V) through the ZIF connector (CE-ATA interface). 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using +3.3V input voltage at 25°C ambient temperature. • Startup mode Startup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
Table 2: DC power Power Consumption at 3.3V Average (W) Startup (max*) 1.15 Read 1.19 Write 1.09 Performance idle (typical) 0.68 Low power idle (typical) 0.48 Standby/Sleep (typical) 0.20 *Maximum is the average of the peak value in 10 msec window 2.7.1.1 Typical current profile 100mA/div Sequential Motor Read Spinup to Ready Performance Idle Standby Load Average 1s/div Figure 2. 8 Unload Average Standby +3.3V Input Supply Current Typical 3.
2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +3.3 volt line. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.7.3 Voltage tolerance Voltage tolerance (including noise): 3.3V ± 5% Lyrion CE-ATA Product Manual, Rev.
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency.
2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditions. Case temperature of the drive operating at 60°C ambient may hit a maximum of 70°C at certain parts of the casing. Above 1,000 feet (305 meters), the maximum operating temperature is derated linearly by 1°C every 1000 feet.
2.8.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, operating or nonoperating, the input shock level is measured at the frame of the drive at the specific location as indicated in Figure 3 below. Figure 3. Location where tri-axial accelerometer will be placed on Lyrion Series drives All shock test cover all the 6 directions, +/- x, y and z axes. The drive axis definition in shown in Figure 4 below. Figure 4.
2.8.6.1 Operating sweep sine vibration The following lists the maximum operating sweep sine vibration levels that the drive may experience while meeting the performance standards specified. It consists of a forward and backward sweep from 10 Hz to 500 Hz to 10 Hz. The drive operates without a hard error while being subjected to the following vibration levels. 10 Hz to 500 Hz @ 2 oct/min 2.8.6.2 1.0 Gs (0 to pk). Maximum displacement may apply below 10 Hz.
2.8.6.4 Nonoperating random vibration The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in the table below. The vibration test level is 3.01 Gs RMS. The drive does not incur any physical damage when subsequently put into operation. Table 5: 2.8.7 Nonoperating random vibration profile. Frequency (Hz) G2/Hz 2.5 1.0 x E-03 5 3.0 x E-02 40 1.8 x E-02 500 1.
2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Discrete tone penalties are added to the A-weighted sound power (LW) with the following formula only when determining compliance: LWt(spec) == LW + 0.1Pt + 0.3 < 4.0 (Bels) where LW = A-weighted sound power level pt == Value of discrete tone penalty [==dLt-6.0 (dBA)] dLt = Tone-to-noise ratio taken in accordance with ISO 7779 at each octave band.
2.11 Reliability Measurement type Specification Nonrecoverable read errors 1 per 1014 bits read, max. Load/Unload (LUL) cycles 300,000 software-controlled 20,000 power loss Power On Hours (POH) per year 500 hours Warranty Per agreement 16 Lyrion CE-ATA Product Manual, Rev.
2.12 Agency certification 2.12.1 Safety certification The drives are recognized in accordance with UL60950-1, CAN/CSA-C22.2 No.60950-1, EN60950 and IEC 60950. 2.12.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE).
2.12.4 2.12.4 China Restriction of Hazardous Substances (RoHS) Directive 中国限制危险物品的指令 This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard. "O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. Lyrion CE-ATA Product Manual, Rev.
20 Lyrion CE-ATA Product Manual, Rev.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: • Do not cover or seal the breather hole! Covering or sealing the breather hole may result in loss of data.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. • If provided, store drive in the protective casing when not in use. • Turn the power off before installing or removing the drive. • Do not apply any force to the drive during handling or installation.
3.2 Drive installation See Figure 7 for drive mechanical dimensions. Follow these installation precautions when inserting the drive: • Follow instructions for the installation of data storage devices, provided with your device’s user manual. • Do not obstruct the breather hole on the drive (see Figure 5). • Handle the drive only by its edges or frame or designated finger grip region during mounting (see Figure 6). Figure 7.
Figure 8. Lyrion Series FPC dimensions 3.3 Mounting considerations • Use an elastic mounting material to protect drives so as to ensure that more shock can be absorbed. • There are guides along the side for mounting. Refer to figure on areas (refer to Figure 9, shaded area) where the mounting material can rest for mounting. • As the drive is a sensitive device, it is not recommended to have any mounting force on the top and bottom surface of the drive other than the recommended mounting surfaces.
4.0 Interface description The drives use the CE-ATA interface. 4.1 Interface signals and connector pins The following table summarizes the signals on the 18-way ZIF CE-ATA interface connector. Table 8: 18-way ZIF (CE-ATA interface) connector signals Pin number Signal Name Definition 1 VSS Ground 2 DAT2 Data line 02 3 DAT3 Data line 03 4 VSS Ground 5 DAT4 Data line 04 6 DAT5 Data line 05 7 Supply Voltage Supply voltage (Standard): 3.
4.2 Supported command set and features This section describes the MMC level commands supported by the drive followed the supported reduced ATA command set and a description of the supported Status and Control Registers (SCR). 4.2.1 MMC command set The following table lists the supported and essential MMC command set for initializing, status checking, error handling, and transferring data. For a detailed description of these commands, refer to the MMC System Specification v 4.
Identify Device command The Identify Device command returns a single block of data (512 bytes or 256 words) to the host, the relevant contents per the CE-ATA specification of which are as shown in the following table Table 11: Identify Device commands Word Description Value 10-19 Serial number: (20 ASCII characters) Drive serial number 23-26 Firmware revision (8 ASCII characters) Current firmware revision 27-46 Drive model number (40 ASCII characters) (ASCII) ST730212CA (for 30GB) (ASCII) ST76
4.2.3 Status and Control Registers The Status and Control Registers (SCR) start at MMC register address 80h and can be accessed only by using CMD60 (RW_MULTIPLE_REGISTER) to read or write to them. The following SCR have been defined (RO = The register may be read only, RW = The register may be read or written to).
5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index A acoustics 15 Active mode 10 agency certification (regulatory) 17 altitude 11 ambient conditions 3 ambient temperature 11 areal density 1, 6 ATA command set 26 ATA-standard commands 26 Australian C-Tick 17 B BPI 6 buffer 1, 6 C EU RoHS directive 17 European Union 17 F FCC verification 18 features 26 formatted capacity 5 FPC dimensions 24 frequency 15 G guaranteed sectors 5 H handling 21 heads 1 height 6 humidity 11 cache 1, 6 case temperature 11 CE mark 17 certification 17 China RoHS directive
nominal power 3 nonoperating random vibration 14 nonoperating shock 1, 12 Nonoperating sweep sine vibration 13 nonrecoverable read errors 16 O Operating random vibration 13 operating shock 1, 12 Operating sweep sine vibration 13 P performance idle 8 Performance idle mode 10 performance Idle mode 7 perpendicular recording heads 1 physical characteristics 6 pins 25 power consumption 7, 8 power management 10 power specifications 7 power-management modes 10 Power-on to Ready 6 precautions 23 programmable powe
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100441950, Rev. A, Printed in U.S.A.
