Product Manual Momentus 5400.3 Blade Server ® ST9160821AB ST9120822AB ST9100828AB ST980815AB ST960815AB ST9402116AB 100409994 Rev.
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100409994, Rev. B August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, SeagateSeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . .
ii Momentus 5400.3 PATA Blade Server Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
iv Momentus 5400.3 PATA Blade Server Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® Momentus®5400.3 drives: • ST9160821AB • ST9120822AB • ST9100828AB • ST980815AB • ST960815AB • ST9402116AB These drives provide the following key features: • 5,400-RPM spindle speed • 8-Mbyte buffer • Quiet operation. Fluid Dynamic Bearing (FDB) motor. • High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.
2 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST9160821AB, ST9120822AB, ST9100828AB, ST980815AB, ST960815AB, and ST9402116AB model drives. 2.1 Specification summary The specifications listed in this table are for quick reference.
Table 1: Specifications for 160 and 120 Gbyte models Drive specification ST9160821AB ST9120822AB Seek power (typical) 2.0 watts Read/write power (typical) Read: 2.0 watts; Write: 1.8 watts Idle mode (typical, low power) 0.8 watts Standby mode 0.2 watts (typical)*** Sleep mode 0.
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST9100828AB ST980815AB Formatted Gbytes (512 bytes/sector)* 100 80 Guaranteed sectors 195,371,568 156,301,488 Bytes per sector 512 Physical read/write heads 3 2 Discs 2 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 5,400 Internal data transfer rate (Mbits/sec max) 352 I/O data-transf
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST9100828AB Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating (max displacement may apply below 10 hz) 1.0 Gs (0 to peak, 5–500 Hz) Vibration, nonoperating (max displacement may apply below 22 hz) 5.0 Gs (0 to peak, 5–500 Hz) ST980815AB Drive acoustics, sound power (bels), 2 disc Idle** 2.4 (typical) 2.6 (max) Performance seek 2.9 (typical) 3.
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST960815AB ST9402116AB Formatted Gbytes (512 bytes/sector)* 60 40 Guaranteed sectors 117,210,240 78,140,160 Bytes per sector 512 Physical read/write heads 2 Discs 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 1 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 5,400 Internal data transfer rate (Mbits/sec max) 352 I/O data-transfer rat
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST960815AB Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating (max displacement may apply below 10 hz) 1.0 Gs (0 to peak, 5–500 Hz) Vibration, nonoperating (max displacement may apply below 22 hz) 5.0 Gs (0 to peak, 5–500 Hz) ST9402116AB Drive acoustics, sound power (bels), 2 disc Idle** 2.4 (typical) 2.6 (max) Performance seek 2.9 (typical) 3.
2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST9160821AB 160 Gbytes 312,581,808 512 ST9120822AB 120 Gbytes 234,441,648 512 ST9100828AB 100 Gbytes 195,371,568 512 ST980815AB 80 Gbytes 156,301,488 512 ST960815AB 60 Gbytes 117,210,240 512 ST9402116AB 40 Gbytes 78,140,160 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method Perdendicular Recording density BPI (bits/inch typical) 835k Track density TPI (tracks/inch typical) 150k Areal density (Gbits/inch2 max) 132 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbits/sec max) 352 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec)* Read Write Track-to-track 1.0 1.5 Average 11.0 13.
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 12. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Duty 50%, power-on hours (POH) of 8,760 per year (24 hours per day, 7 days per week operation). Actual drive case temperature should not exceed 45°C (113°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating Nonoperating 2.10.
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.
2.13 Reliability Measurement type Specification Nonrecoverable read errors 1 per 1014 bits read, max. Annualized Failure Rate (AFR) <1.79% Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles Warranty 5 years on distribution units.
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (RoHS) The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical substances, including Lead (Pb), in electronic products effective July 2006.
20 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.2 Jumper settings 3.2.1 Master/slave configuration Use the options jumper block shown in Figure 5 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3.2.2. The “Master or single drive” option is the factory default setting. Drive is master (or single drive) Drive is slave Cable select Figure 5. Jumper settings 3.2.
3.3 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 6 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling. • Use only M3 x 0.5 mounting screws. • Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).
24 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.
4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-6 Standard...
Table 6: Supported commands Command name Command code (in hex) Security Unlock F2H Seek 70H Set Drive Parameters 91H Set Features EFH Set Max Address F9H Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right. Address Password Lock Unlock Freeze Lock Set Multiple Mode C6H Sleep 99H, E6H S.M.A.R.T.
Table 6: Supported commands Command name Command code (in hex) Security Freeze Lock F5H Security Disable Password F6H 28 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
4.1.2 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 on page 26. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
Word Description Value 57–58 Current capacity in sectors xxxxH 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH 60–61 Total number of user-addressable LBA sectors available (see Section 2.
Word Description Value 129–159 Seagate-reserved xxxxH 160–254 ATA-reserved 0000H 255 Integrity word xxA5H Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data. Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active.
4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index Numerics 3D Defense System 1 A acoustics 16 AFR 17 agency certification (regulatory) 17 altitude 14 ambient conditions 3 ambient temperature 11, 14 Annualized Failure Rate 17 areal density 10 ATA interface 25 ATA-standard commands 26 Australian C-Tick 18 autodetection 1 average seek time 11 B BPI 10 buffer 1, 10 burst 1 C cable select 1 cable-select option 22 cache 1, 10 case temperature 14 CE mark 17 certification 17 Check Power Mode 27 chemical substances 19 commands 26 compliance 17 conducted no
interface 10, 25 interface signals 25 interference 18 interleave 10 internal data-transfer rate OD 10 ISO document 7779 16 J jumper settings 22 K Korean RRL 18 L LBA mode 9 length 10 Load/Unload 17 logical geometry 9 M master/slave 1 Master/slave configuration 22 maximum temperature 14 modes 25 monitoring 1 mounting the drive 21, 23 N noise 13 nominal power 3 nonoperating shock 15 nonoperating vibration 15 nonrecoverable read errors 17 O operating shock 15 operating vibration 15 P physical characteri
single-track seeks 11 Sleep 12, 27 sound 16 specifications 3 spindle speed 10 Spinup 12 spinup power 12 Standby 12, 27 Standby Immediate 27 Standby mode 12 Standby to Ready 11 static-discharge precautions 21 subassembly 18 support services 33 surge immunity 16 T technical support services 33 temperature 14 temperature gradient 14 time to ready 11 TMR 1 track density 10 track-to-track seek time 11 TUV North America 17 U UL 1950 17 V vibration 15 voltage 13 voltage dips, interrupts 16 voltage tolerance 13
38 Momentus 5400.3 PATA Blade Server Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100409994, Rev. B, Printed in U.S.A.