Product Manual Momentus 7200.3 SATA ST9320421AS ST9320421ASG ST9250421AS ST9250421ASG ST9200421AS ST9200423ASG ST9160411AS ST9160411ASG ST9120411AS ST9120411ASG ST980411AS ST980411ASG 100512541 Rev.
Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100512541, Rev. B, July 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . . . . . .
ii Momentus 7200.3 SATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Mounting dimensions—top, side and end view . . . . . . . . . . . . . .
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus® 7200.3 SATA model drives: • ST9320421AS • ST9320421ASG • ST9250421AS • ST9250421ASG • ST9200421AS • ST9200423ASG • ST9160411AS • ST9160411ASG • ST9120411AS • ST9120411ASG • ST980411AS • ST980411ASG These drives provide the following key features: • 7,200-RPM spindle speed. • 16-Mbyte buffer.
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9320421AS, ST9320421ASG, ST9250421AS, ST9250421ASG, ST9200421AS, ST9200423ASG, ST9160411AS, ST9160411ASG, ST9120411AS, ST9120411ASG, ST980411AS and ST980411ASG models. 2.1 Specification summary table The specifications listed in this table are for quick reference.
Table 1: Drive specifications Drive specification ST9320421AS ST9320421ASG Standby to ready (sec typical) 3.0 Track-to-track seek time, read (msec typical) 1.0 Average seek, read (msec typical) 11.0 Average seek, write (msec typical) 13.0 Startup current, +5V (max) 1.0 amps Seek power (typical) 2.3 watts ST9250421AS ST9250421ASG Read power (typical) 2.1 watts Write power (typical) 2.3 watts Idle mode, low power (typical) 0.75 watts Standby mode 0.
Table 1: Drive specifications Drive specification ST9320421AS ST9320421ASG ST9250421AS ST9250421ASG ST9200421AS ST9200423ASG ST9160411AS ST9160411ASG ST9120411AS ST9120411ASG ST980411AS ST980411ASG Load/Unload (U/UL) cycles 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 50,000 hard power on/off cycles 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity 600,000 software-controlled power on/off cycles 50,000 hard
2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.
2.6 Physical characteristics Drive specification Height (mm) (inches) 9.5 +/-0.2 0.374 +/-0.0078 Width (mm) (inches) 69.85 +/-0.249 2.75 +/-0.0098 Length (mm) (inches) 100.33 +/-0.25 3.95 +/-.010 Typical weight ST9320421AS ST9320421ASG ST9250421AS ST9250421ASG ST9200421AS ST9200423ASG 110 grams 0.238 pounds ST9160411AS ST9160411ASG ST9120411AS ST9120411ASG ST980411AS ST980411ASG 2.7 105 grams 0.227 pounds Seek time Seek measurements are taken with nominal power at 25°C ambient temperature.
2.8 Start/stop times Time to ready Typical Max @ 25°C Power-on to Ready (sec) 4.0 8.0 Standby to Ready (sec) 3.0 8.0 2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature.
2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
2.10 Environmental specifications This section provides the temperature, humidity, shock, and vibration specifications for Momentus 7200.3 SATA drives. 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
2.10.6.2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1,000 Gs based on a nonrepetitive half-sine shock pulse of 1 msec duration.
2.
To enable the Free Fall Protection feature on ST9320421ASG, ST9250421ASG, ST9200423ASG, ST9160411ASG, ST9120411ASG and ST980411ASG models, use Set Features command 41h. To disable this feature, use Set Features command C1h. Information about Free Fall Events that have occurred is available through SMART Attribute FEh. Note. The Free Fall Protection feature is provided only on ST9320421ASG, ST9250421ASG, ST9200423ASG, ST9160411ASG, ST9120411ASG and ST980411ASG models. 2.14 Agency certification 2.14.
2.14.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.
2.15 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1 European Union Restriction of Hazardous Substances (RoHS) Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives. Momentus 7200.3 SATA Product Manual, Rev.
18 Momentus 7200.3 SATA Product Manual, Rev.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.2 Configuring the drive Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are Device 0 (master) devices.
3.4 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling. • Use only M3 UNC mounting screws. • Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb). • Four (4) threads (0.
22 Momentus 7200.3 SATA Product Manual, Rev.
4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
Table 7: Segment Power Serial ATA connector pin definitions Pin Function Definition P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.
4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 32.for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Multiple Mode C6h S.M.A.R.T. Disable Operations B0h/D9h S.M.A.R.T. Enable/Disable Autosave B0h/D2h S.M.A.R.T. Enable Operations B0h/D8h S.M.A.R.T. Enable/Disable Auto Offline B0h/DBh S.M.A.R.T. Enable One Attribute Modification B0h/E0h S.M.A.R.T. Execute Offline B0h/D4h S.M.A.R.T.
Command name Command code (in hex) Standby Immediate 94h or E0h ATA-standard security commands Security Set Password F1h Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up.
Word Description Value 27–46 Drive model number: (40 ASCII characters, padded with blanks to end of string) ST9320421AS ST9320421ASG ST9250421AS ST9250421ASG ST9200421AS ST9200423ASG ST9160411AS ST9160411ASG ST9120411AS ST9120411ASG ST980411AS ST980411ASG 47 (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16) 8010H 48 Reserved 0000H 49 Standard Standby timer, IORDY supported and may be disabled 2F00H 50 ATA-reserved 0000H 51 PIO data-transfer cycle timing mod
Word Description Value 69–74 ATA-reserved 0000H 75 Queue depth 0000H 76 Serial ATA capabilities 0508H 77 ATA-reserved 0000H 78 Serial ATA features supported 0048H 79 Serial ATA features enabled 0040H 80 Major version number 003EH 81 Minor version number 0000H 82 Command sets supported 306BH 83 Command sets supported 4001H 84 Command sets support extension 4000H 85 Command sets enabled 30xxH 86 Command sets enabled 0001H 87 Command sets enable extension 4000H 88
Word Description Value 129– 159 Seagate-reserved xxxxH 160– 254 ATA-reserved 0000H 255 Integrity word xxA5H Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data: Description (if bit is set to 1) 30 Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active.
4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index A ACA 14 acoustics 4, 12 Active mode 10 Address 25 AFR 13 Agency certification 14 Altitude 11 Altitude, nonoperating 4 Altitude, operating 4 Ambient temperature 4, 11 ambient temperature 7 Annualized Failure Rate 13 Annualized Failure Rate (AFR) 4 Areal density 3, 6 ATA commands 25 ATA data-transfer modes supported 3 Australia/New Zealand Standard AS/NZS3548 1995 14 Australian Communication Authority (ACA) 14 Australian C-Tick 14 Average seek time 7 Average seek, read 4 B bels 4 BPI 3 buffer 3, 6 Byt
guaranteed sectors 5, 6 N H noise 9 nominal power 7 Nonoperating shock 12 Nonoperating vibration 12 Nonrecoverable read errors 4 nonrecoverable read errors 13 handling 19 Handling precautions 19 heads 6 Height 3 height 7 humidity 4 I I/O data-transfer rate 3, 6 Identify 25 Identify Device 25 Identify Device command 27 Idle 8, 26 Idle and Standby timers 10 Idle Immediate 26 Idle mode 4, 10 Idle mode power 8 IEC950 14 Information Technology Equipment (ITE) 14 Initialize Device Parameters 25 Input noise r
Read/write heads 6 Read/write power 4 read/write power and current 8 Recording density 3, 6 Recording method 6 Recording technology 6 Relative humidity 4, 11 Reliability 13 resistance 9 Retries 25 RF 13 RoHS 16 RPM 3 RRL 14 S S.M.A.R.T. 26 S.M.A.R.T.
38 Momentus 7200.3 SATA Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100512541, Rev.