Product Manual Savvio 10K.4 SAS ® Standard Models Self-Encrypting Drive Models ST9600204SS ST9450404SS ST9600104SS ST9450304SS 100539221 Rev.
Revision history Revision Rev. A Date 12/15/09 Sheets affected or comments Initial release. Copyright © 2009 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100539221, Rev. A December 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents 1.0 Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Applicable standards and reference documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1.1 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.1 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5.2 Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5.3 Effective altitude (sea level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5.4 Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5.5 Air cleanliness . . . . . . .
10.6 10.7 11.0 10.5.2 Differential signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 SAS-2 Specification compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv Savvio 10K.4 SAS Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Current profiles for 600GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current profiles for 450GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600GB (at 3Gb) DC current and power vs. input/output operations per second . . . . . . . .
1.0 Scope This manual describes Seagate Technology® LLC, Savvio® 10K.4 SAS (Serial Attached SCSI) disc drives. Savvio drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part number 100293071) describes the general SAS characteristics of this and other Seagate SAS drives. The Self-Encrypting Drive Reference Manual, part number 100515636, describes the interface, general operation, and security features available on Self-Encrypting Drive models.
2.0 Applicable standards and reference documentation The drives documented in this manual have been developed as system peripherals to the highest standards of design and construction. The drives depend on host equipment to provide adequate power and environment for optimum performance and compliance with applicable industry and governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation.
2.1.2 Electromagnetic compliance Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and C-Tick Marking. The drive was tested in a representative system for typical applications. The selected system represents the most popular characteristics for test platforms.
2.1.3 European Union Restriction of Hazardous Substances (RoHS) The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical substances, including Lead (Pb), in electronic products effective July 2006. A number of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers regarding the presence of RoHS substances in these parts and materials.
3.0 General description Savvio drives provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI interface is designed to meet next-generation computing demands for performance, scalability, flexibility and high-density storage requirements.
3.1 Standard features Savvio® 10K.4 SAS drives have the following standard features: • • • • • • • • • • • • • • • • • • • • • • • • • • 1.
3.3 • • • • • • Programmable multi-segmentable cache buffer 600Mb/s maximum instantaneous data transfers. 10K RPM spindle. Average latency = 3.0ms Background processing of queue Supports start and stop commands (spindle stops spinning) Adaptive seek velocity; improved seek performance Note. 3.4 • • • • • Performance There is no significant performance difference between Self-Encrypting Drive and standard (nonSelf-Encrypting Drive) models. Reliability Annualized Failure Rate (AFR) of 0.
3.7 Factory-installed options You may order the following items which are incorporated at the manufacturing facility during production or packaged before shipping. Some of the options available are (not an exhaustive list of possible options): • Other capacities can be ordered depending on sparing scheme and sector size requested. • Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection against transit damage.
4.0 Performance characteristics This section provides detailed information concerning performance-related characteristics and features of Savvio drives. 4.1 Internal drive characteristics Drive capacity Read/write data heads Bytes per track Bytes per surface Tracks per surface (total) Tracks per inch Peak bits per inch Areal density Internal data rate Disc rotation speed Avg rotational latency 4.2 ST9600204SS ST9600104SS 600 6 677,557 100,021 147,620 240,000 1,430 343 1.62 10K 3.
4.2.2 Format command execution time for 512-byte sectors (minutes) ST9600204SS ST9600104SS ST9450404SS ST9450304SS Maximum (with verify) 184 136 Maximum (without verify) 92 68 Note. 4.2.3 There is no significant difference in the format time between SED and non-SED models of the same capacity.
4.4 Prefetch/multi-segmented cache control The drive provides a prefetch (read look-ahead) and multi-segmented cache control algorithms that in many cases can enhance system performance. Cache refers to the drive buffer storage space when it is used in cache operations. To select this feature, the host sends the Mode Select command with the proper values in the applicable bytes in page 08h.
If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made available for future read cache hits. The same buffer space and segmentation is used as set up for read functions. The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of RCD.
5.0 Reliability specifications The following reliability specifications assume correct host and drive operational interface, including all interface timings, power supply voltages, environmental requirements and drive mounting constraints. Seek error rate: Read Error Rates1 Recovered Data Unrecovered Data Miscorrected Data Interface error rate: Mean Time Between Failure (MTBF): Annualized Failure Rate (AFR): Preventive maintenance: 1.
5.1.3 Seek errors A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks.
Caution. 5.2.4 The drive motor must come to a complete stop prior to changing the plane of operation. This time is required to insure data integrity. S.M.A.R.T. S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended to recognize conditions that indicate imminent drive failure and is designed to provide sufficient warning of a failure to allow you to back up the data before an actual failure occurs. Note.
S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of the number of errors for the current interval. This counter is referred to as the Failure Counter. Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to set thresholds for the number of errors and their interval. If the number of errors exceeds the threshold before the interval expires, the error rate is considered to be unacceptable.
5.2.6 Drive Self Test (DST) Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level. There are two test coverage options implemented in DST: 1. Extended test 2. Short test The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive.
5.2.6.2.3 Short and extended tests DST has two testing options: 1. short 2. extended These testing options are described in the following two subsections. Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan segment. Short test (Function Code: 001b) The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within 120 seconds.
5.2.
6.0 Physical/electrical specifications This section provides information relating to the physical and electrical characteristics of the drive. 6.1 PowerChoiceTM power management Drives using the load/unload architecture provide programmable power management to tailor systems for performance and greater energy efficiency. The table below lists the supported PowerChoice modes. The further you go down in the table, the more power savings you get.
6.1.1 PowerChoice reporting methods PowerChoiceTM provides these reporting methods for tracking purposes: Request Sense command reports • Current power condition • Method of entry Note. Processing the Request Sense command does not impact the drive’s power save state.
Table 2: 600GB standard drive DC power requirements Notes Voltage 600GB standard model 3.0Gb mode 600 GB standard model 6.0Gb mode (Amps) (Amps) (Amps) (Amps) +5V +12V [2] +5V +12V [2] Regulation [5] ±5% ±5% [2] ±5% ±5% [2] Avg idle current DC [1] [7] 0.33 0.24 0.34 0.24 Advanced Idle Current Idle_A 3σ 0.32 0.24 0.33 0.24 Idle_B 3σ 0.23 0.21 0.24 0.21 Idle_C 3σ 0.23 0.11 0.24 0.10 Standby 3σ 0.23 0.06 0.24 0.05 Idle_A - Active 3σ 0.72 1.58 0.70 1.
Table 3: 450GB standard model DC power requirements Notes Voltage 450GB standard model 3.0Gb mode 450GB standard model 6.0Gb mode (Amps) (Amps) (Amps) (Amps) +5V +12V [2] +5V +12V [2] Regulation [5] ±5% ±5% [2] ±5% ±5% [2] Avg idle current DC [1] [7] 0.34 0.24 0.35 0.24 Advanced Idle Current Idle_A 3σ 0.34 0.24 0.35 0.24 Idle_B 3σ 0.24 0.21 0.25 0.21 Idle_C 3σ 0.24 0.10 0.25 0.10 Standby 3σ 0.24 0.06 0.25 0.06 Idle_A - Active 3σ 0.68 1.58 0.78 1.
[2] [3] [4] [5] For +12 V, a –10% tolerance is allowed during initial spindle start but must return to ±5% before reaching 9,936 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator. See +12V current profile in Figure 16. This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive. See paragraph 6.3.
General DC power requirement notes. 1. Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown. 2. The +5V and +12V supplies should employ separate ground returns. 3. Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device. 4.
6.3.3 Current profiles The +12V and +5V current profiles for the Savvio 10K.4 drives are shown below. F1 F2 Figure 16. 26 Current profiles for 600GB models Savvio 10K.4 SAS Product Manual, Rev.
F1 F2 Figure 17. Current profiles for 450GB models Note: All times and currents are typical. See Tables 2 and 3 for maximum current requirements. Savvio 10K.4 SAS Product Manual, Rev.
6.4 Power dissipation 600 GB models in 3Gb operation Typical power dissipation under operating conditions in 3Gb operation is 8.23 watts (28.08 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 18). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123.
600GB models in 6Gb operation Typical power dissipation under operating conditions in 6Gb operation is 8.29 watts (28.29 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 18). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Figure 19.
450GB models in 3Gb operation Typical power dissipation under operating conditions in 3Gb operation is 8.48 watts (28.93 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 18). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Figure 20.
450GB models in 6Gb operation Typical power dissipation under operating conditions in 6Gb operation is 8.53 watts (29.10 BTUs per hour). To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 18). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Figure 21.
b. Non-operating –40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 68°F (20°C) per hour. This specification assumes that the drive is packaged in the shipping container designed by Seagate for use with drive. Figure 22. Location of the HDA temperature check point 6.5.2 Relative humidity The values below assume that no condensation on the drive occurs. a. Operating 5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour. b.
6.5.4.1 Shock a. Operating—normal The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding: • 40 Gs at a maximum duration of 11ms (half sinewave) • 25 Gs at a maximum duration of 2ms (half sinewave) Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds. b. Non-operating The limits of non-operating shock shall apply to all conditions of handling and transportation.
c. Packaged Disc drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined in the table below. For additional details refer to Seagate specifications 30190-001 (under 100 lbs/45 kg) or 30191-001 (over 100 lbs/45 Kg). Package size Packaged/product weight Drop height <600 cu in (<9,800 cu cm) 600-1800 cu in (9,800-19,700 cu cm) >1800 cu in (>19,700 cu cm) >600 cu in (>9,800 cu cm) Any 0-20 lb (0 to 9.1 kg) 0-20 lb (0 to 9.1 kg) 20-40 lb (9.
6.5.4.2 Vibration a. Operating—normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 5-500 Hz @ 0.5 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Operating normal translational random flat profile 10 - 500 Hz (translational random flat profile) 0.5 GRMS b.
6.5.7 Acoustics Sound power during idle mode shall be 3.0 bels typical when measured to ISO 7779 specification. There will not be any discrete tones more than 10 dB above the masking noise on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive. 6.5.8 Electromagnetic susceptibility See Section 2.1.1.1. 36 Savvio 10K.4 SAS Product Manual, Rev.
6.6 Mechanical specifications The following nominal dimensions are exclusive of the decorative front panel accessory. However, dimensions of the front panel are shown in figure below. Refer to Figure 24 for detailed mounting configuration dimensions. See Section 9.3, “Drive mounting.” Height: Width: Depth: Weight: 0.583 in 2.755 in 3.945 in 0.459 pounds 14.81 mm 69.98 mm 100.2 mm 0.208 kilograms Temperature Measurement Location Figure 24. Mounting configuration dimensions Savvio 10K.
7.0 About self-encrypting drives Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, commonly known as “protection of data at rest.” These drives are compliant with the Trusted Computing Group (TCG) Enterprise Storage Specifications as detailed in Section 2.2. The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the computer, storage and digital communications industry.
7.2.2 Locking SP The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the Locking SP is available using the BandMasterX or EraseMaster passwords. Since the drive owner can define up to 16 data bands on the drive, each data band has its own password called BandMasterX where X is the number of the data band (0 through 15). 7.2.3 Default password When the drive is shipped from the factory, all passwords are set to the value of MSID.
7.6 Cryptographic erase A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the drive to change the data encryption key for a particular band. Once changed, the data is no longer recoverable since it was written with one key and will be read using a different key. Since the drive overwrites the old key with the new one, and keeps no history of key changes, the user data can never be recovered.
8.0 Defect and error management Seagate continues to use innovative technologies to manage defects and errors. These technologies are designed to increase data integrity, perform drive self-maintenance, and validate proper drive operation. SCSI defect and error management involves drive internal defect/error management and SAS system error considerations (errors in communications between the initiator and the drive).
The drive firmware error recovery algorithms consists of 11 levels for read recoveries and five levels for write. Each level may consist of multiple steps, where a step is defined as a recovery function involving a single reread or re-write attempt. The maximum level used by the drive in LBA recovery is determined by the read and write retry counts. Table 4 equates the read and write retry count with the maximum possible recovery time for read and write recovery of individual LBAs.
8.4 Background Media Scan Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4 available from the T10 committee. BMS performs sequential reads across the entire pack of the media while the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it can avoid placing data in suspect locations on the media.
8.7 Idle Read After Write Idle Read After Write (IRAW) utilizes idle time to verify the integrity of recently written data. During idle periods, no active system requests, the drive reads recently written data from the media and compares it to valid write command data resident in the drives data buffer. Any sectors that fail the comparison result in the invocation of a rewrite and auto-reallocation process. The process attempts to rewrite the data to the original location.
9.0 Installation Savvio disc drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive. SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accomodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws.
9.2 Cooling Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 6.5.1, "Temperature." The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disc assembly (HDA). You should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 6.5.1.
9.3 Drive mounting Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface. The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm).
10.0 Interface requirements This section partially describes the interface requirements as implemented on Savvio drives. Additional information is provided in the SAS Interface Manual (part number 100293071). 10.1 SAS features This section lists the SAS-specific features supported by Savvio drives. 10.1.1 task management functions Table 5 lists the SAS task management functions supported.
10.2 Dual port support Savvio SAS drives have two independent ports. These ports may be connected in the same or different SCSI domains. Each drive port has a unique SAS address. The two ports have the capability of independent port clocking (e.g. both ports can run at 6Gb/s or the first port can run at 6Gb/s while the second port runs at 3Gb/s.) The supported link rates are 1.5, 3.0, or 6.0 Gb/s.
10.3 SCSI commands supported Table 7 lists the SCSI commands supported by Savvio drives.
Table 7: Supported commands Command name Command code Supported Last n Deferred Errors or Asynchronous Events page (0Bh) N Last n Error Events page (07h) N Non-medium Error page (06h) Y Pages Supported list (00h) Y Read Error Counter page (03h) Y Read Reverse Error Counter page (04h) N Self-test Results page (10h) Y Start-stop Cycle Counter page (0Eh) Y Temperature page (0Dh) Y Verify Error Counter page (05h) Y Write error counter page (02h) Y Mode Select (same pages as Mode Sense
Table 7: Supported commands Command name Command code Supported Read Buffer (modes 0, 2, 3, Ah and Bh supported) 3Ch Y (non-SED drives only) Read Capacity (10) 25h Y Read Capacity (16) 9Eh/10h N Read Defect Data (10) 37h Y Read Defect Data (12) B7h Y Read Long 3Eh Y (non-SED drives only) Read Long (16) 9Eh/11h N Reassign Blocks 07h Y Receive Diagnostic Results 1Ch Y Supported Diagnostics pages (00h) Y Translate page (40h) Y Release 17h Y Release (10) 57h Y Report LU
Table 7: Supported commands Command name Command code Supported Test Unit Ready 00h Y Verify (10) 2Fh Y BYTCHK bit Y Verify (12) AFh N Verify (16) AFh N Verify (32) 7Fh/000Ah N Write (6) 0Ah Y Write (10) 2Ah Y DPO bit Y FUA bit Y Write (12) AAh N Write (16) 8Ah N Write (32) 7Fh/000Bh N Write and Verify (10) 2Eh Y DPO bit Y Write and Verify (12) AEh N Write and Verify (16) 8Eh N Write and Verify (32) 7Fh/000Ch N Write Buffer (modes 0, 2, supported) 3Bh
10.3.1 Inquiry data Table 8 lists the Inquiry command data that the drive should return to the initiator per the format given in the SAS Interface Manual.
On drives requiring unique saved values, the required unique saved values are stored into the saved values storage location on the media prior to shipping the drive. Some drives may have unique firmware with unique default values also. On standard OEM drives, the saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping. 3. Current values Current values are volatile values being used by the drive to control its operation.
Table 9: Mode Sense data for ST9600204SS and ST9600104SS drives MODE DATA HEADER: 01 92 00 10 00 00 00 08 BLOCK DESCRIPTOR: 45 dd 2f b0 00 00 02 00 MODE PAGES: DEF CHG 81 0a c0 0c ff 00 00 00 05 00 ff ff 81 0a ff ff 00 00 00 00 ff 00 ff ff DEF CHG 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00 DEF CHG 83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 ba 00 24 40 00 00 00 83 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DEF CHG
Table 10: Mode Sense values for ST9450404SS and ST9450304SS drives MODE DATA HEADER: 01 92 00 10 00 00 00 08 BLOCK DESCRIPTOR: 34 65 f8 70 00 00 02 00 MODE PAGES: DEF CHG 81 0a c0 0c ff 00 00 00 05 00 ff ff 81 0a ff ff 00 00 00 00 ff 00 ff ff DEF CHG 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00 DEF CHG 83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 ba 00 24 40 00 00 00 83 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DEF C
10.4 Miscellaneous operating features and conditions Table 11 lists various features and conditions. A “Y” in the support column indicates the feature or condition is supported. An “N” in the support column indicates the feature or condition is not supported.
10.4.1 SAS physical interface Figure 27 shows the location of the SAS device connector J1. Figures 28 and 29 provide the dimensions of the SAS connector. Details of the physical, electrical, and logical characteristics are provided within this section. The operational aspects of Seagate’s SAS drives are provided in the SAS Interface Manual.. Figure 27. Physical interface Savvio 10K.4 SAS Product Manual, Rev.
0.80 (6X) 5.92 7.62 4.65 0.52 2.00 (3X) 0.45 5.08 0.08 x 45 0.03 (7X) 0.10 M E 42.73 REF. 41.13 0.30 0.15 0.20 B 0.05 (2X) C A B 4.00 1.10 0.08 0.15 D 0.30 CL OF DATUM D 0.05 (4X) A B R0.30 C 0.08 (4X) SEE Detail1 33.43 0.05 B 15.875 15.875 1.27 (14X) 1.27 (6X) 0.84 5.08 0.05 (22X) 0.15 B 4.90 0.08 0.35MIN P15 P1 S7 S1 CL OF DATUM B Figure 28. 60 SAS device plug dimensions Savvio 10K.4 SAS Product Manual, Rev.
Detail A 6.10 S14 2.25 S8 0.05 x 45 (5X) 0.05 0.40 4.85 0.30 0.05 0.10 B 0.05 X 45 (3X) CORING ALLOWED IN THIS AREA. E 4.40 0.15 R0.30 0.08 SEE Detail 2 C 1.95 0.08 A 45 0.35 3.90 0.05 0.15 SECTION C - C SECTION A - A 0.08 0.05 CONTACT SURFACE FLUSH TO DATUM A 0.03 65 1.23 0.08 0.05 0.05 1.90 0.08 30 Detail 2 2.40 0.08 0.10 A SECTION B - B D Figure 29. SAS device plug dimensions (detail) Savvio 10K.4 SAS Product Manual, Rev.
10.4.2 Physical characteristics This section defines physical interface connector. 10.4.3 Connector requirements Contact your preferred connector manufacturer for mating part information. Part numbers for SAS connectors will be provided in a future revision of this publication when production parts are available from major connector manufacturers. The SAS device connector is illustrated in Figures 28 and 29. 10.4.
10.4.6 SAS transmitters and receivers A typical SAS differential copper transmitter and receiver pair is shown in Figure 30. The receiver is AC coupling to eliminate ground shift noise. .01 TX RX Differential Transfer Medium Transmitter 100 TY Figure 30. SAS transmitters and receivers 10.4.7 Power Receiver 100 RY .01 The drive receives power (+5 volts and +12 volts) through the SAS device connector. Three +12 volt pins provide power to the drive, 2 short and 1 long.
The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. See Table 15 for the output characteristics of the LED drive signals. Table 15: LED drive signal State Test condition Output voltage LED off, high 0 V ≤VOH ≤3.6 V -100 µA < IOH < 100 µA LED on, low IOL = 15 mA 0 ≤VOL ≤0.225 V 10.5.
11.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index Numerics 12 volt pins 63 5 volt pins 63 6 Gbps 64 A abort task set function 48 AC coupling 63 AC power requirements 21 ACA active status 58 ACA active, faulted initiator status 58 acoustics 36 active LED Out signal 63 actuator 7 assembly design 5 adaptive caching 58 Admin SP 38 AES-128 data encryption 38 AFR 31 air cleanliness 35 Air flow 31 air flow 46 illustrated 46 air inlet 46 altitude 32 ambient 32 ambient temperature 31, 46 ANSI documents SCSI 4 Serial Attached SCSI 4 asynchronous event notific
dimensions 37 disc rotation speed 9 drive 35 drive characteristics 9 drive failure 14 Drive Locking 39 drive mounting 37, 47 drive select 62 dual port support 49 E electrical description of connector 62 signal characteristics 63 specifications 20 electromagnetic compatibility 2 Electromagnetic Compatibility (EMC) 3 Electromagnetic Compatibility control Regulation 3 electromagnetic susceptibility 36 EMI requirements 2 encryption engine 38 encryption key 39 environment 46 environmental limits 31 requirements
logical block address 11 logical block reallocation scheme 6 logical block size 6, 10 logical segments 11 temperature 32 non-operating vibration 35 M office environment 35 operating 32, 33, 35 option selection 62 options 8 out-of-plane distortion 47 maintenance 13 Makers Secure ID 38 maximum delayed motor start 22, 23 maximum start current 22, 23 maximum temperature 31 mean time between failure.
receivers 63 recommended mounting 34 Recoverable Errors 13 recovered media data 13 reference documents 4 relative humidity 32 reliability 7 specifications 13 reliability and service 14 repair and return information 19 reporting actual retry count 58 reservation conflict status 58 resonance 32 return information 19 RNG 39 RoHS 4 rotation speed 9 S safety 2 SAS interface 62 physical interface 59 task management functions 48 SAS documents 4 SAS Interface Manual 2, 4 SAS-2 Specification 64 SCSI interface comma
W warranty 19 Z zero latency read 58 zone bit recording (ZBR) 6 Savvio 10K.4 SAS Product Manual, Rev.
72 Savvio 10K.4 SAS Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100539221, Rev.
