ST1 Series ST650211CF ST650211FX ST625211CF ST625211FX
ST1 Series ST650211CF ST650211FX ST625211CF ST625211FX Rev.
©2004, Seagate Technology LLC All rights reserved Publication number: 100325578, Rev. A June 2004 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications.
Revision status summary sheet Revision Rev. A Date 06/30/04 Sheets Affected All.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Drive care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Handling precautions . . . . . . . . . . . . . . . . . . . . . . . . .
vi ST1 Series Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. ST1 Series CompactFlash+ disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ST1 Series Flex (IDE interface) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Typical 3.3V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii ST1 Series Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® ST1® Series drives: • ST650211CF and ST625211CF CompactFlash+ Type II disc drives. • ST650211FX and ST625211FX Flex (IDE interface) disc drives. These drives provide the following key features: • 3,600-RPM spindle speed and 2-Mbyte buffer combine for superior performance. • Quiet operation. Fluid Dynamic Bearing (FDB) motor.
1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST650211CF, ST650211FX, ST625211FX, and ST625211CF model drives. 2.1 Power, access times and acoustics The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
Table 1: Specifications Drive specification ST650211CF ST650211FX Average seek, read (msec typical/max) 16.0/17.0 Full-stroke seek (msec typical/max) 26.0/27.0 Seek power (typical 3.3V) 226 mA Read/write power (typical 3.3V) 300/310 mA Performance idle mode (typical 3.3V) 200 mA Low power idle mode (typical 3.3V) 90 mA ST625211CF ST625211FX Standby/Sleep mode (typical) 30 mA Voltage tolerance (including noise) 3.
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST650211CF ST650211FX 5 Gbytes 9,767,520 512 ST625211CF ST625211FX 2.5 Gbytes 4,883,760 512 2.
2.5 Recording and interface technology Technology Specification Interface CompactFlash 2.0 (CF+ 2.0) Recording method RLL 0,20 Recording density BPI (bits/inch max) 651,000 Track density TPI (tracks/inch max) 105,000 Areal density (Gbits/inch2 max) 68.3 Spindle speed (RPM) (± 0.2%) 3,600 Internal data-transfer rate OD (Mbits/sec max) 9.67 Sustained data transfer rate OD (Mbytes/sec max) 7.0 I/O data-transfer rate (Mbytes/sec max) 33.
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. *Seek times (msec) Read Write Typical Max Typical Max Track-to-track 2.0 2.5 3.
2.9 Power specifications The drive receives DC power (+3.3V or +5V) through the CompactFlash interface connector for ST650211CF and ST625211CF models, and (+3.3V only) through the Flex interface connector for ST650211FX and ST625211FX models. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using +3.3V and +5.0V input voltage at 25°C ambient temperature.
Table 2: DC power ST1 Power Consumption (W) Max current the average of the peak value in 10ms window Average 3.3V Max 3.3V Average 5.0V Max 5.0V Current 330 330 Spinup 300 300 Load/Unload current 300 300 Write 310 330 310 330 Read 310 330 320 340 Seek 226 300 226 300 Performance idle 200 205 Low power idle 90 92 Standby/Sleep 30 33 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T.
2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 20 MHz. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note.
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. The drive features the following power-management modes: Table 3: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Enabled Idle, low power Parked Rotating Disabled Standby/Sleep Parked Stopped Disabled • Active mode The drive is in Active mode during the read/write and seek operations.
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating Nonoperating 2.10.
2.10.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, Operating or Non-Operating, the input shock level shall be measured at the frame of the disk drive at the specific location indicated by the red ellipse in Figure 4 below for the CF and interface drives. Finger Grip Area S1 CF drive S1 interface drive Figure 4. Location where tri-axial accelerometer will be placed on S1 drive.
2.10.6 Vibration All vibration specifications assume that the drive is mounted securely in a fixture that do not have fixture resonances in the frequency test range. The input vibration is applied through the disk drive guide rails of the device under test. Testing is carried out in the x, y and z axes. 2.10.6.1 Operating Sweep Sine Vibration The following lists the maximum Operating Sweep Sine Vibration levels that the drive may experience while meeting the performance standards specified.
2.10.6.4 Operating Random Vibration The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in the table below. The vibration test level is 3.01Gs RMS. The drive will not incur any physical damage when subsequently put into operation. Table 5: Non-Operating Random Vibration profile. Frequency (Hz) G2/Hz 2.5 1.0 x E-03 5 3.0 x E-02 40 1.8 x E-02 500 1.8 x E-02 ST1 Series Product Manual, Rev.
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Discrete tone penalties are added to the A-weighted sound power (LW) with the following formula only when determining compliance: LWt(spec) == LW + 0.1Pt + 0.3 < 4.0 (Bels) where LW = A-weighted sound power level pt == Value of discrete tone penalty [==dLt-6.0 (dBA)] dLt = Tone-to-noise ratio taken in accordance with ISO 7779. All measurements are consistent with ISO document 7779.
2.13 Reliability Measurement type Specification Nonrecoverable read errors 1 per 1014 bits read, max. Mean time between failures 100,000 power-on hours At nominal power, 40°C ambient temperature. Max case temperature: 60°C at the case measurement location shown in Figure 6 and 7.
2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL60950 Third edition, CAN/CSA-C22.2 No. 60950-00 Third edition, EN 60950-2000 Third edition, and IEC 60950 Third edition as tested by TUV North America.. 2.14.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC).
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. Radio and television interference.
20 ST1 Series Product Manual, Rev.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
FINGER GRIP G F Breather Hole Do not cover E B D C A N J K H L M Pin 50 Pin 1 A B C D E F G H J K L M N Dimension Table Inches Millimeters 0.197 max 5.00 max 1.433 ± .006 36.40 ± .15 1.685 ± .004 42.80 ± .10 1.015 ± .003 2x 25.78 ± .07 1.152 ± .010 29.25 ± .25 0.299 ± .010 7.61 ± .25 0.394 min 10.00 min 0.063 ± .002 1.60 ± .05 0.040 ± .003 2x 1.01 ± .07 0.039 ± .002 1.00 ± .05 0.039 ± .004 2x 1.00 min 0.065 ± .004 1.65 ± .10 0.243 ± .004 2x 6.16 ± .10 Figure 6.
FINGER GRIP G A F Breather Hole Do not cover E B D R S P C H T J K L M A B C D E F G H J K L M P R S T Dimension Table Inches Millimeters 0.197 max 5.00 max 1.433 ± .006 36.40 ± .15 1.685 ± .004 42.80 ± .10 1.015 ± .003 2x 25.78 ± .07 1.152 ± .010 29.25 ± .25 0.299 ± .010 7.61 ± .25 0.394 min 10.00 min 0.063 ± .002 1.60 ± .05 0.040 ± .003 2x 1.01 ± .07 0.039 ± .002 1.00 ± .05 0.039 ± .004 2x 1.00 min 0.065 ± .004 1.65 ± .10 0.906 ± .003 23.00 ± .07 0.669 ± .020 17.00 ± .50 0.414 ± .020 10.51 ± .
24 ST1 Series Product Manual, Rev.
4.0 interface description These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–2. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the CompactFlash interface, refer to CF+ and CompactFlash Spec Rev 2.0. 4.
Table 8: CompactFlash+ interface connector signals PC Card Memory Mode True IDE Mode[4] PC Card I/O Mode 24 WP O OT3 24 -IOIS16 O OT3 24 -IOIS16 O ON3 25 -CD2 O Ground 25 -CD2 O Ground 25 -CD2 O Ground 26 -CD1 O Ground 26 -CD1 O Ground 26 -CD1 O Ground 27 D11 [1] I/O I1Z, OZ3 27 D11 [1] I/O I1Z, OZ3 27 [1] D11 I/O I1Z, OZ3 28 D12[1] I/O I1Z, OZ3 28 D12[1] I/O I1Z, OZ3 28 D12[1] I/O I1Z, OZ3 29 D13 [1] I/O I1Z, OZ3 29 D13 [1] I/O I1
4.1.1 Flex Interface Connector Signals The following table summarizes the signal on the Seagate Flex interface connector. For a detailed description of these signals, refer to ATA-7 Specifications Revision 7.0.
Table 9: Flex interface connector signals 24 DD9 Data bus bit 9 25 GROUND Ground 26 DD13 Data bus bit 13 27 CSEL Cable select 28 DD12 Data bus bit 12 29 DD7 Data bus bit 7 30 DD6 Data bus bit 6 31 DD5 Data bus bit 5 32 DD4 Data bus bit 4 33 DD3 Data bus bit 3 34 DD2 Data bus bit 2 35 GROUND Ground 36 DD1 Data bus bit 1 37 DD0 Data bus bit 0 38 DMARQ DMA request 39 DMACK- DMA Acknowledge 40 IOCS16- Data transfer size is one word per transfer cycle 41 CS0
4.1.2 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the CF commands, refer to CF+ and CompactFlash Spec Rev 2.0.
Table 10: Supported commands Does command cause drive to transition to active mode? [1] Command name Command code (in hex) Write Multiple C5H X Write Multiple w/o Erase CDH X Write Sectors 30H, 31H X Write Sector w/o Erase 38H X Write Verify 3CH X ATA-standard power-management commands Check Power Mode 98H or E5H Idle 97H or E3H X Idle Immediate 95H or E1H X Sleep 99H or E6H Standby 96H or E2H Standby Immediate 94H or E0H [1] [2] ‘X’ indicates: If the drive is in Standby mo
4.1.3 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 31. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
Word ATA specification CF specification Value Value Value 47 (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16) Maximum number of sectors on Read/Write Multiple command 8010H 8010H 8010H 48 Reserved Reserved 0000H 0000H 0000H 49 Capabilities Capabilities 0A00H 0B00H 0B00H 50 Reserved Reserved 0000H 0000H 0000H 51 Obsolete PIO data transfer cycle timing mode 0200H 0200H 0200H 52 Obsolete Obsolete 0000H 0000H 0000H 53 Words 64–70 and 88
Word ATA specification CF specification Value Value Value 84 Features/Command sets supported Features/Command sets supported 4000H 4000H 4000H 85 Features/Command sets enabled Features/Command sets enabled 7068H 7068H 7068H 86 Features/Command sets enabled Features/Command sets enabled 100CH 100CH 100DH 87 Features/Command sets enabled Features/Command sets enabled 4000H 4000H 4000H 88 Ultra DMA support and current mode (see note following this table) Reserved 0000H 0007H
Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data: Description (if bit is set to 1) 34 Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported.
4.1.4 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead feature enabled and write caching feature disabled.
Table 11: Features register values 69H NOP- Accepted for backward compatibility Yes Yes 81H Disable 8 bit transfer; Only in True IDE mode Yes Yes 82H Disable write cache.
4.1.5 Card Information Structure (CIS) Information for CF CIS information for the CF card is as follows: Address Data Description of data Common Memory Device Information in 5V Operation 000H 01H CISTPL_DEVICE 002H 04H TPL_LINK = 04 bytes 004H DFH CISTPL_DEVICE: Device ID Device type (bit 4...7 = D (DTYPE_FUNCSPEC) WPS (write protect switch) (bit 3) = 1 (non WP) Device Speed (bit 0...2) = 7 (DSPEED_EXT) 006H 12H CISTPL_DEVICE: EXT (bit 7) = 0 Mantissa (bit 3...6) = 2 (1.
Manufacturer Identification String 022H 20H CISTPL_MANFID 024H 04H TPL_LINK = 04 bytes 026H 11H TPL_MANF: Manufacturer’s ID code (Low byte) = 11 for SEAGATE 028H 01H TPL_MANF: Manufacturer’s ID code (High byte) = 01 for SEAGATE 02AH 00H TPLMID_CARD: Product code (Low byte) (Manufacturer Info) 02CH 00H TPLMID_CARD: Product code (High byte) (Manufacturer Info) 02EH 15H CISTPL_VERS_1 030H 0EH TPL_LINK = 0Eh bytes 032H 04H TPLLV1_MAJOR: Major Version Number (JEIDA 4.2/PCMCIA 2.
060H 22H CISTPL_FUNCE: (Function Extension Tuple) 062H 03H TPL_LINK =3 bytes 064H 02H TUPLE_TYPE: (Extension Type) = 02 (Basic PC Card ATA Interface) 08H TPLFE_DATA V : Vpp[2::1] (bit0,1) = 00 (Vpp not required) S : Silicon (bit2) = 0 (Rotating Device) U : Inique (bit3) = 0 (Single Drive) D : Dual Drive (bit4) = 0 (Single Drive) 068H 0FH TPLFE_DATA P0 : Sleep (bit0) = 1 (Support Sleep mode) P1 : Standby (bit1) = 1 (Support Standby mode) P2 : Idle (bit2) = 1 (Support Idle mode) P3 : Auto (bit 3)
A1H TPCE_FS: (Feature Selection Byte) Power (bit0,1) = 01 (Vcc Only) Timing (bit2) = 0 I/O (bit3) = 0 Interrupt (bit4) = 0 Memory (bit5,6) = 01 Misc (bit7) = 1 TPCE_PD (Power Description Structure) 082H 27H TPCE_PS: Parameter Selection Byte NomV (bit0) =1 MinV (bit1) = 1 MaxV (bit2) =1 PeakI (bit5) =1 084H 55H TPCE_PD: Power Parameter Definition (NomV) Exponent (bit 0..2) = 5 (1V) -->5.0V Mantissa (bit3..6) = A (5.0) 086H 4DH TPCE_PD: Power Parameter Definition (MinV) Exponent (bit 0..
00H TPCE_INDX: (Configuration Table Index Byte) Config Entry Number (bit0..5) = 00 (Memory Mode) Default (bit6) = 0 Interface (bit7) = 0 (Interface Field Exist) 01H TPCE_FS Power (bit0,1) = 01 (Vcc Only) Timing (bit2) = 0 I/O (bit3) = 0 Interrupt (bit4) = 0 Memory (bit5,6) = 00 Misc (bit7) = 0 21H TPCE_PD: Paramter Selection Byte NomV (bit0) =1 MinV (bit1) = 0 MaxV (bit2) =0 PeakI (bit5) =1 09EH B5H TPCE_PD: Power Parameter Defintion (NomV) Exponent (bit0..2) = 5 (1V) - -+ -->3.3V Mantissa (bit3..
99H TPCE_FS: (Feature Selection Byte) Power (bit0,1) = 01 (Vcc Only) Timing (bit2) = 0 I/O (bit3) = 0 Interrupt (bit4) = 0 Memory (bit5,6) = 01 Misc (bit7) = 1 TPCE_PD (Power Description Structure) 0B0H 27H TPCE_PD: Parameter Selection Byte NomV (bit0) =1 MinV (bit1) = 1 MaxV (bit2) =1 PeakI (bit5) =1 0B2H 55H TPCE_PD: Power Parameter Definition (NomV) Exponent (bit 0..2) = 5 (1V) -->5.0V Mantissa (bit3..6) = A (5.0) 0B4H 4DH TPCE_PD: Power Parameter Definition (MinV) Exponent (bit 0..
For PC Card ATA I/O in Contiguous Memory Mode in 3.3V Operation (Default) 0C6H 1BH CISTPL_CFTABLE_ENTRY: (16 Bit PCCard Configuration Table Entry Tuple) 0C8H 07H TPCE_LINK = 07h bytes 01H TPCE_INDX :(Configuration Table Index Byte) Config Entry Number (bit0..
99H TPCE_FS: (Feature Selection Byte) Power (bit0,1) = 01 (Vcc Only) Timing (bit2) = 0 I/O (bit3) = 0 Interrupt (bit4) = 0 Memory (bit5,6) = 01 Misc (bit7) = 1 TPCE_PD (Power Description Structure) 0E2H 27H TPCE_PD: Parameter Selection Byte NomV (bit0) =1 MinV (bit1) = 1 MaxV (bit2) =1 PeakI (bit5) =1 0E4H 55H TPCE_PD: Power Parameter Definition (NomV) Exponent (bit 0..2) = 5 (1V) -->5.0V Mantissa (bit3..6) = A (5.0) 0E6H 4DH TPCE_PD: Power Parameter Definition (MinV) Exponent (bit 0..
0FEH 100H EEH TPCE_IR: (Interrupt Request Description Structure) IRQ Line 0..15 (bit0..3) = E MASK (bit4) = 0 Level (bit5) = 1 Pulse (bit6) = 1 Share (bit7) = 1 20H TPCE_MI: (Miscellaneous Features Field ) Max Twin Card (bit0..2) = 0 Audio (bit3) = 0 Read Only (bit4) = 0 Power Down (bit5) = 1 (Support Power Down Mode) For PC Card ATA I/O Primary Mode (1F0-1F7, 3F6, 3F7) in 3.
C3H TPCE_INDX :( Configuration Table Entry Tuple) Config Entry Number (bit0..5) = 03 (Secondary I/O Mode) Default (bit6) = 1 Interface (bit7) = 1 (Interface Field Exist) 41H TPCE_IF: (Interface Description Field) Interface Type (bit0..
130H 01H 132H 07H TPCE_IO: I/O Address Block Length = 8 134H 76H TPCE_IO: I/O Address Range Description Field #2 Address = 376 136H 03H 138H 01H TPCE_IO: I/O Address Block Length = 2 EEH TPCE_IR: (Interrupt Request Description Structure) IRQ Line 0..15 (bit0..3) = E MASK (bit4) = 0 Level (bit5) = 1 Pulse (bit6) = 1 Share (bit7) = 1 20H TPCE_MI: (Miscellaneous Features Field ) Max Twin Card (bit0..
14EH 1EH TPCE_PD: Extension = 1Eh = +30 --+ 150H 14H CISTPL_NO_LINK 152H 00H TPCE_LINK 154H FFH CISTPL_END 48 ST1 Series Product Manual, Rev.
5.0 Seagate Technology support services Online Services Internet www.seagate.com for information about Seagate products and services. Worldwide support is available 24 hours daily by e-mail for your questions. Presales Support: www.seagate.com/support/email/email_presales.html or DiscPresales@Seagate.com Technical Support: www.seagate.com/support/email/email_disc_support.html or DiscSupport@Seagate.com mySeagate my.seagate.
Warranty Service Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct customers should contact their Seagate service center representative for warranty-related issues. Resellers or end users of drive products should contact their place of purchase or one of the Seagate warranty service centers for assistance. Have your drive’s “ST” model number and serial number available.
USA/Canada/Latin America Support Services Presales Support Call Center Americas Toll-free 1-877-271-32851 Direct dial +1-405-324-47301 FAX +1-405-324-4704 Toll-free 1-800-SEAGATE2 Direct dial +1-405-324-47003 FAX +1-405-324-4702 Toll-free 1-800-468-34724 Direct dial +1-405-324-47204 FAX / Internet +1-405-324-4722 1-800-636-6349 +1-905-660-4936 +1-905-660-4951 www.memofix.com — +55-21-2509-7267 +55-21-2507-6672 www.mainformatica.com.br/produtos.
European Support Services For presales and technical support in Europe, dial the toll-free number for your specific location. If your location is not listed here, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Monday through Friday. The presales and technical support call center is located in Oklahoma City, USA. For European warranty service, dial the toll-free number for your specific location.
Asia/Pacific Support Services For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/ Pacific toll-free numbers are available from 6:00 A.M. to 10:45 A.M. and 12:00 P.M. to 6:00 P.M. (Australian Eastern time) Monday through Friday, except as noted. If your location is not listed here, direct dial one of our technical support locations. Warranty service is available from 9:00 A.M. to 6:00 P.M. April through October, and 10:00 P.M. to 7:00 P.M.
54 ST1 Series Product Manual, Rev.
Index Numerics 3D Defense System 1 A acoustics 16 Active mode 11 agency certification (regulatory) 18 altitude 12 ambient conditions 3 ambient temperature 7, 12 areal density 1, 6 ATA-standard commands 29 Australian C-Tick 18 average seek time 7 B BPI 6 buffer 1, 6 C cache 1, 6 card information structure 37 case temperature 12 CE mark 18 certification 18 CF+ interface connector signals 25 Check Power Mode 30 CIS 37 commands 29 compliance 18 conducted noise 10 conducted RF immunity 16 configuring the driv
K LBA mode 5 length 6 Load/Unload 17 Load/Unload curren 9 logical geometry 5 low power idle 9 read/write heads 5 read/write power and current 8 recording and interface technology 6 recording density 6 recording heads 1 recording method 6 register 35 relative humidity 12 reliability 17 resistance 10 RF 16 M S maximum temperature 12 Mean time between failures (MTBF) 17 modes 25 mounting the drive 21 safety certification 18 SeaTools 1 sectors 5 Seek 29 seek mode 8 seek time 7 Seeking 9 Set Features 29 Se
track density 6 track-to-track seek time 7 TUV North America 18 U UL 1950 18 V voltage 10 voltage dips, interrupts 16 voltage tolerance 10 W Warranty 17 warranty 2 weight 6 wet bulb temperature 12 width 6 Write Buffer 29 Write DMA 29 Write Multiple 30 Write Sectors 30 ST1 Series Product Manual, Rev.
58 ST1 Series Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100325578, Rev.
