Product Manual Seagate® 600 SSD Standard 2.5” 7mm Usage Based models Standard 2.5” 5mm Usage Based models ST480HM000 ST240HM000 ST120HM000 ST480HM001 ST240HM001 ST120HM001 100722309 Rev.
Document Revision History Revision Date Description of changes Rev. A 04/11/2013 Initial release. © 2013 Seagate Technology LLC. All rights reserved. Publication number: 100722309, Rev. A April 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURES Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Typical 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Mounting configuration dimensions (7mm models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Mounting configuration dimensions (5mm models) . . . . . . . . . . . . . . . . . .
Seagate Technology Support Services For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technical-support/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers Warranty terms will vary based on type of warranty chosen: “Managed Life” or “Usage Based”. Consult your Seagate sales representative for warranty terms and conditions.
1.0 INTRODUCTION This manual describes the functional, mechanical and interface specifications for the following Seagate® 600 SSD model drives: 2.5" Usage Based 7mm Model 2.5" Usage Based 5mm Model ST480HM000 ST480HM001 ST240HM000 ST240HM001 ST120HM000 ST120HM001 These drives provide the following key features: • Multi-Level Cell (19nm MLC) NAND Flash storage. • Serial ATA 3.1 Host Interface (SATA 6Gb/s). • High instantaneous (burst) data-transfer rates (up to 530MB/s).
2.0 DRIVE SPECIFICATIONS Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: Capacity 2.5” Usage Based Warranty 480GB ST480HM000 240GB ST480HM001 ST240HM000 120GB ST240HM001 ST120HM000 ST120HM001 Product data communicated in this manual is specific only to the model numbers listed in this manual.
Drive specification ST480HM000 ST480HM001 Vibration, random nonoperating ST240HM000 ST240HM001 ST120HM000 ST120HM001 20–2000 Hz: 11.08 Grms 1 LBA per 1016 bits read Nonrecoverable read errors, max Annualized Failure Rate (AFR) 0.58% Warranty 3 Year Usage Based Lifetime Power cycles 25,000 Supports Hotplug operation per Serial ATA Revision 3.0 specification Yes *One GB equals one billion bytes when referring to drive capacity.
2.4 PERFORMANCE, RECORDING AND INTERFACE TECHNOLOGY 2.4.1 Interface technology 480GB models 240GB models Interface Serial ATA (SATA-II) Interface Speeds Supported 6Gb/s, 3Gb/s, 1.5Gb/s Maximum Burst Transfer Rate 600MB/s Hot Plug Support Yes Native Command Queuing Support Yes Trim Support Yes 2.4.2 Recording technology Flash Memory Type NAND MLC Emulated LBA Size (Bytes) 512 Default transfer alignment offset 0 Typical Data Retention with Power removed (at 30°C) 12 months 2.4.
2.5 PHYSICAL CHARACTERISTICS Maximum height ST480HM000, ST240HM000 & ST120HM000 ST480HM001, ST240HM001 & ST120HM001 7.00 mm (0.276 in) 5.00 mm (0.197 in) Maximum width 70.10 mm (2.760 in) Maximum length 100.45 mm (3.955 in) Max weight 2.6 77 g (0.170lb) 67 g (0.148 lb) TIME TO READY 480GB Power-on to Ready (sec) SEAGATE 600 SSD PRODUCT MANUAL, REV.
2.7 POWER SPECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector. See 2 on page 16. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, at 35°C ambient temperature. • Startup power Startup power is measured from the time of power-on to the time that the drive reaches operating condition and can process media access commands.
Table 3 240GB DC power requirements Parameter Voltage ST240HM000, ST240HM001 (6.0Gb) +5V Power +/- 5% (watts) Average Idle Current 0.22 1.10 Average Sleep Current 0.10 0.50 Maximum Start Current 0.95 DC (Peak DC) 0.52 AC (Peak AC) 0.38 Regulation Peak Operating Current (random read): Typical DC 0.32 1.57 Maximum DC 0.34 1.68 Maximum DC (peak) 0.78 3.90 Typical DC 0.41 2.03 Maximum DC 0.46 2.27 Maximum DC (peak) 1.22 6.10 Typical DC 0.43 2.06 Maximum DC 0.44 2.
Table 4 120GB DC power requirements Parameter Voltage ST120HM000, ST120HM001 (6.0Gb) +5V Power +/- 5% (watts) Average Idle Current 0.22 1.10 Average Sleep Current 0.10 0.50 Maximum Start Current 0.95 DC (Peak DC) 0.54 AC (Peak AC) 0.70 Regulation Peak Operating Current (random read): Typical DC 0.34 1.67 Maximum DC 0.35 1.72 Maximum DC (peak) 0.82 4.10 Typical DC 0.51 2.54 Maximum DC 0.56 2.18 Maximum DC (peak) 1.42 7.10 Typical DC 0.43 2.30 Maximum DC 0.44 2.
2.7.2.1 Figure 1. Typical current profiles Typical 5V Startup and Operation Current Profile SEAGATE 600 SSD PRODUCT MANUAL, REV.
2.8 ENVIRONMENTAL SPECIFICATIONS 2.8.1 Temperature Temperature is defined as the drive's internal temperature as reported by SMART attribute 194 for operation or the drive case temperature for non-operating. Above 1000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3048 meters). Operating: 0° to 70°C (32° to 158°F) Nonoperating: –40° to 75°C (–40° to 167°F) 2.8.
2.8.6.1 Operating vibration The maximum random vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. This specification does not cover connection issues that may result from testing at this level. 20–2000 Hz 2.8.6.2 11.
2.10 RELIABILITY 2.10.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate - AFR - of 0.58%. AFR and MTBF are population statistics that are not relevant to individual units. AFR and MTBF specifications are based on the following assumptions: • • • • 8760 power-on-hours per year. 250 average power cycles per year. Operations at nominal voltages.
2.11 AGENCY CERTIFICATION 2.11.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2.11.2 Electromagnetic compatibility Drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007.
2.12 ENVIRONMENTAL PROTECTION Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.12.1 European Union Restriction of Hazardous Substances (RoHS) Directive The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006.
3.0 CONFIGURING AND MOUNTING THE DRIVE This section contains the specifications and instructions for configuring and mounting the drive. 3.1 HANDLING AND STATIC-DISCHARGE PRECAUTIONS After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.4 DRIVE MOUNTING You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottommounting holes. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 in (0.76 mm) around the entire perimeter of the drive for cooling as a guideline. Please refer to Section 3.5 for final cooling requirements. • Use only M3 x 0.5 metric mounting screws. • Four (4) threads (0.080 in) minimum screw engagement recommended.
Note. These dimensions conform to the Small Form Factor Standard documented in SFF-8120 and SFF-8146 found at www.sffcommittee.org. Figure 4. Mounting configuration dimensions (5mm models) SEAGATE 600 SSD PRODUCT MANUAL, REV.
3.5 COOLING Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 2.8.1, "Temperature." The rack, cabinet, or drawer environment for the drive must provide heat removal. You should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 2.8.1.
4.0 SERIAL ATA (SATA) INTERFACE These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
Table 7 summarizes the 1.8” drive Signal and Power SATA Plug. Table 7 1.
4.3 SUPPORTED ATA COMMANDS The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 31for details and subcommands used in the S.M.A.R.T. implementation.
COMMAND NAME COMMAND CODE (IN HEX) Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable Operations B0H / D8H S.M.A.R.T. Execute Offline B0H / D4H S.M.A.R.T. Read Data B0H / D0H S.M.A.R.T. Read Log Sector B0H / D5H S.M.A.R.T. Return Status B0H / DAH S.M.A.R.T.
4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 8 on page 22. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. see Section 2.0 on page 3 for default parameter settings.
WORD DESCRIPTION VALUE 67 Minimum PIO transfer cycle time without flow control (120ns) 0078H 68 Minimum PIO transfer cycle time with IORDY flow control (120ns) 0078H 69 Additional Features and Commands supported.
WORD DESCRIPTION VALUE 127 Obsolete 0000H 128 Security status 0001H 129–159 Vendor specific xxxxH 160–167 Reserved for the CompactFlash Association 0000H 168 Device Nominal Form Factor 0003H 169 DATA SET MANAGEMENT features supported 0001H 170–173 Additional Product Identifier (ATA String) 0000H 174–175 Reserved 0000H 176–197 Reserved 0000H 198–199 Reserved 8000H 200–205 Reserved 0000H 206 SCT Command Transport 0000H 207–208 Reserved for CE-ATA 0000H 209 Alignment
Bit Word 69 5 Read zero after Trim is supported 6 Optional ATA 28-bit commands supported 8 Download Microcode DMA supported 9 Set Max Password DMA and Set Max Unlock DMA supported 10 Write Buffer DMA Supported 11 Read Buffer DMA Supported 12 DEVICE CONFIGURATION IDENTIFY DMA and DEVICE CONFIGURATION SET DMA are supported 13 Long Physical Sector Alignment Error Reporting Control is supported 14 Deterministic read after Trim is supported Bit Word 76 0 Shall be cleared to zero 1 Suppor
Bit Word 83 0 DOWNLOAD MICROCODE command is supported 1 Obsolete 2 CFA feature set is supported 3 APM feature set is supported 4 Obsolete 5 PUIS feature set is supported 6 SET FEATURES subcommand is required to spin-up after power-up 7 Reserved 8 SET MAX security extension is supported 9 AAM feature set is supported 10 48-bit Address feature set is supported 11 DCO feature set is supported 12 Mandatory FLUSH CACHE command is supported 13 FLUSH CACHE EXT command is supported 14
Bit Word 87 0 SMART error logging is supported 1 SMART self-test supported 3 The Media Card Pass Through Command feature set is supported 5 The GPL feature set is supported 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported 8 The 64-bit World wide name is supported 13 The IDLE IMMEDIATE command with UNLOAD FEATURE is supported 14 Shall be set to one 15 Shall be cleared to zero Bit Word 119 0 Reserved 1 Write-Read-Verify feature set is supported 2 WRITE UNCORRECT
4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
INDEX A F ACA 14 acceleration 12 Agency certification 14 air flow illustrated 19 altitude 11 ambient temperature 7 Annualized Failure Rate (AFR) 13 ATA commands 22 Australia/New Zealand Standard AS/NZ CISPR22 14 Australian Communication Authority (ACA) 14 Australian C-Tick 14 FCC verification 14 features 2 Federal Communications Commission 14 Flush Cache 22 Flush Cache Extended 22 Formatted capacity 4 C Handling precautions 16 heads 4 height 6 humidity 11 cables and connectors 16 capacity 4 CE mark 14
INDEX Nonoperating vibration 12 NOP 22 O Operating shock 11 Operating vibration 12 P Peak operating mode 7 Performance 5 Physical characteristics 6 point-to-point 2, 16 Power consumption 7 Power specifications 7 precautions 16 printed circuit board 16 Q quick reference 3 R Radiated RF immunity 12 Radio and television interference 14 radio frequency (RF) 12 Read Buffer 22 Read DMA 22 Read DMA Extended 22 Read FPDMA queued 22 Read Log Ext 22 Read Multiple 22 Read Multiple Extended 22 Read Native Max Addre
INDEX Write Multiple Extended 23 Write Multiple FUA Extended 23 Write Sectors 23 Write Sectors Extended 23 write uncorrectable 23 SEAGATE 600 SSD PRODUCT MANUAL, REV.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100722309, Rev.
