Product Manual Desktop SSHD ST2000DX001 ST1000DX001 100726566 Rev.
Document Revision History Revision Date Description of Change Rev. A 04/30/2013 Initial release © 2013 Seagate Technology LLC. All rights reserved. Publication number: 100726566, Rev. A April 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. SeaTools is either a trademark or registered trademark of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
Contents Seagate Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1 About the SATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Desktop SSHD Product Manual, Rev.
Figures Figure 1 Figure 2 Figure 3 Attaching SATA cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Mounting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Mounting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Desktop SSHD Product Manual, Rev.
Desktop SSHD Product Manual, Rev.
Seagate Technology Support Services For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technicalsupport/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit http://www.seagate.
Desktop SSHD Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® Desktop SSHD model drives: ST2000DX001 ST1000DX001 These drives provide the following key features: • 8GB NAND flash • 7200 RPM spindle speed. • High instantaneous (burst) data-transfer rates (up to 600MB per second). • TGMR recording technology provides the drives with increased areal density. • State-of-the-art cache and on-the-fly error-correction algorithms.
Introduction www.seagate.com The SATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All SATA devices behave like Device 0 devices. For additional information about how SATA emulates parallel ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 3.0”. The specification can be downloaded from www.sata-io.org.
2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST2000DX001 2.1 ST1000DX001 Specification summary tables The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual.
Drive Specifications www.seagate.com Table 1 Drive specifications summary for 2TB and 1TB models (continued) Drive Specification* ST2000DX001 ST1000DX001 Voltage tolerance (including noise) 5V: ±5% 12V: +10% / -7.5% 5V: ±5% 12V: +10% / -7.
www.seagate.com 2.2 Drive Specifications Formatted capacity Model Formatted capacity* Guaranteed sectors ST2000DX001 2000GB 3,907,029,168 ST1000DX001 1000GB 1,953,525,168 Bytes per sector 4K *One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.
Drive Specifications 2.5 www.seagate.com Physical characteristics Maximum height 2TB 26.1mm / 1.028 in 1TB 20.17mm / 0.7825 in Maximum width (all models) 101.6mm / 4.0 in ( ± 0.010 in) Maximum length (all models) 146.99mm / 5.787 in Typical weight 2TB 535g / 1.18 lb 1TB 400g / 0.88 lb Cache buffer 2.6 64MB (64,768kb) Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics.
www.seagate.com Drive Specifications 2.8.1 Power consumption Power requirements for the drives are listed in Table 2 and Table 3. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
Drive Specifications www.seagate.com Table 2 DC power requirements (2-disk: 2TB model) Power dissipation (2-disk values shown) Avg (watts 25° C) Avg 5V typ amps Avg 12V amps Spinup — — 2.0A Idle2* † 4.50 0.196 0.296 Operating 6.70 0.525 0.340 Standby 0.75 0.136 0.005 Sleep 0.75 0.136 0.005 Table 3 DC power requirements (1-disk: 1TB model) Power dissipation (1-disk values shown) Avg (watts 25° C) Avg 5V typ amps Avg 12V amps Spinup — — 2.0 Idle2* † 3.36 0.152 0.
www.seagate.com Drive Specifications 2.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program.
Drive Specifications www.seagate.com 2.9.2 Temperature gradient Operating 20°C per hour (68°F per hour max), without condensation Non-operating 30°C per hour (86°F per hour max) 2.9.3 Humidity 2.9.3.1 Relative humidity Operating 5% to 95% non-condensing (30% per hour max) Nonoperating 5% to 95% non-condensing (30% per hour max) 2.9.3.2 Wet bulb temperature Operating 37.7°C (99.9°F max) Non-operating 40°C (104°F max) 2.9.4 Altitude Operating –304.8m to 3048m (–1000 ft. to 10,000+ ft.
www.seagate.com 2.9.5.1 Drive Specifications Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80 Gs based on half-sine shock pulses of 2 ms during read operations. Shocks should not be repeated more than two times per second. 2.9.5.
Drive Specifications www.seagate.com Table 4 Fluid Dynamic Bearing (FDB) motor acoustics Idle* Seek 2 Disks (2TB) 2.4 bels (typical) 2.6 bels (max) 2.6 bels (typical) 2.7 bels (max) 1 Disk (1TB) 2.2 bels (typical) 2.3 bels (max) 2.3 bels (typical) 2.4 bels (max) *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. 2.10.
www.seagate.com Drive Specifications 2.13.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.
Drive Specifications www.seagate.com 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.
3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
Configuring and Mounting the Drive www.seagate.com Figure 1 Attaching SATA cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Desktop SSHD drives support latching SATA connectors. 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 2 and Figure 3 for drive mounting dimensions.
Figure 3 Mounting dimensions Temperature Check Point Desktop SSHD Product Manual, Rev.
Configuring and Mounting the Drive 26 www.seagate.com Desktop SSHD Product Manual, Rev.
4.0 SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6. For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
SATA Interface www.seagate.com Table 6 SATA connector pin definitions (continued) Segment Power Pin Function Definition P1 V33 3.3V power P2 V33 3.3V power P3 V33 3.3V power, pre-charge, 2nd mate P4 Ground 1st mate P5 Ground 2nd mate P6 Ground 2nd mate P7 V5 5V power, pre-charge, 2nd mate P8 V5 5V power P9 V5 5V power P10 Ground 2nd mate P11 Ground or LED signal If grounded, drive does not use deferred spin P12 Ground 1st mate.
www.seagate.
Table 7 SATA standard commands (continued) Command name Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Command code (in hex) Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable/Disable Autosave B0H / D2H S.M.A.R.T. Enable Operations B0H / D8H S.M.A.R.T. Execute Offline B0H / D4H S.M.A.R.T.
www.seagate.com SATA Interface 4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on page 28. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
SATA Interface www.seagate.com Table 8 Identify Device commands (continued) Word Description Value 59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB).
www.seagate.com SATA Interface Table 8 Identify Device commands (continued) Word Description Value 92 Master password revision code FFFEH 93 Hardware reset value xxxxH 94 Automatic acoustic management 8080H 95–99 ATA-reserved 0000H 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
SATA Interface 34 www.seagate.com 5 GPL feature set is supported. 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported. 7 WRITE DMA QUEUED FUA EXT command is supported. 8 64-bit World Wide Name is supported. 9-10 Obsolete. 11-12 Reserved for TLC. 13 IDLE IMMEDIATE command with IUNLOAD feature is supported. 14 Shall be set to 1. 15 Shall be cleared to 0. Bit Word 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported.
www.seagate.com SATA Interface 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
SATA Interface www.seagate.com 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
Index A ACA 21 acceleration 19 acoustics 19 Active 17 Active mode 17 Agency certification 20 altitude 18 Ambient temperature 17 ambient temperature 14, 15 areal density 13 ATA commands 28 Australia/New Zealand Standard AS/NZ CISPR22 21 Australian Communication Authority (ACA) 21 Australian C-Tick 21 Average latency 14 Average seek time 14 B buffer 14 C cables and connectors 23 cache 14 capacity 13 CE mark 21 certification 20 Check Power Mode 28 China RoHS directive 22 compatibility 21 Conducted noise 16 Con
N noise 16 nominal power 14 Nonoperating shock 19 Nonoperating vibration 19 O operating 16 Operating power 15 Operating shock 19 Operating vibration 19 P Physical characteristics 14 point-to-point 9, 23 Power consumption 15 power dissipation 16 Power modes 17 Power specifications 14 Power-management modes 17 Power-on to Ready 14 precautions 23 printed circuit board 23 programmable power management 17 prominent discrete tone 20 Q quick reference 11 R Radiated RF immunity 20 radio and television interference
U UL60950-1 20 V voltage 15 Voltage dips, interrupts 20 Voltage tolerance 16 W weight 14 wet bulb temperature 18 width 14 Write Buffer 30 Write DMA 30 Write DMA Extended 30 Write DMA FUA Extended 30 Write DMA Without Retries 30 Write Log Extended 30 Write Multiple 30 Write Multiple Extended 30 Write Multiple FUA Extended 30 Write Sectors 30 Write Sectors Extended 30 Write Sectors Without Retries 30 Desktop SSHD Product Manual, Rev.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100726566, Rev.
