Product Manual Seagate Enterprise NAS HDD ® ST6000VN0001 ST5000VN0001 ST4000VN0001 ST3000VN0001 ST2000VN0001 Gen 2 100762258 Rev.
Document Revision History Revision Date Description of Change Rev. A 11/12/2014 Initial release. Rev. B 11/18/2014 Page 6, 10 & 13. © 2014 Seagate Technology LLC. All rights reserved. Publication number: 100762258, Rev. B November 2014 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 About the SATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures Figure 1 Figure 2 Figure 3 Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Mounting dimensions (2, 3, 4 & 5TB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Mounting dimensions (6TB model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Seagate Enterprise NAS HDD Product Manual, Rev.
Seagate Technology Support Services ® For information regarding online support and services, visit: http://www.seagate.com/about/contact-us/technical-support/ Available services include: • Presales & Technical support • Global Support Services telephone numbers & business hours • Authorized Service Centers For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.
1.
www.seagate.com 2.0 Drive Specifications Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST6000VN0001 2.1 ST5000VN0001 ST4000VN0001 ST3000VN0001 ST2000VN0001 Specification summary tables The specifications listed in Table 1 are for quick reference.
Table 1 Drive specifications summary Drive Specification* ST6000VN0001 ST5000VN0001 ST4000VN0001 ST3000VN0001 ST2000VN0001 37.7°C max (operating) 40.0°C max (nonoperating) Wet bulb temperature (max) Altitude, operating –304m to 3048m (–1000 ft to 10,000 ft) Altitude, non-operating (below mean sea level, max) –304m to12,192m (–1000ft to 40,000+ ft) 70 Gs at 2ms (read) 40 Gs at 2ms (write) Operational shock (max) Non-operational shock (max) 300 Gs at 2ms 2Hz to 22Hz: 0.
www.seagate.com 2.2.1 Drive Specifications LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137GB. 2.
www.seagate.com 2.6 Drive Specifications Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead.
www.seagate.com Drive Specifications Table 2 DC power requirements Power dissipation (6/5TB models) Avg (25° C) Avg 5V typ Avg 12V typ Spinup — — <=1.8A Idle* † 7.20W 0.20A 0.52A Operating 9.00W 0.24A 0.65A Standby 0.60W 0.12A 0.01A Sleep 0.60W 0.12A 0.01A Power dissipation (4/3TB models) Avg (25° C) Avg 5V typ Avg 12V typ Spinup — — <=1.8A Idle* † 5.90W 0.30A 0.36A Operating 6.70W 0.357A 0.41A Standby 0.60W 0.12A 0.01A Sleep 0.60W 0.12A 0.
www.seagate.com 2.8.4 Drive Specifications Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, users can control power management through the system setup program.
www.seagate.com Drive Specifications 2.9.3 Humidity 2.9.3.1 Relative humidity Operating 5% to 90% non-condensing (30% per hour max) Nonoperating 5% to 95% non-condensing (30% per hour max) 2.9.3.2 Wet bulb temperature Operating 37.7°C (99.9°F max) Non-operating 40°C (104°F max) 2.9.4 Altitude Operating –304m to 3048m (–1000 ft. to 10,000 ft.) Non-operating –304m to 12,192m (–1000 ft. to 40,000+ ft.) 2.9.
www.seagate.com Drive Specifications 2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note For seek mode tests, the drive is placed in seek mode only.
www.seagate.com Drive Specifications 2.13 Agency certification 2.13.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2.13.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007.
www.seagate.com Drive Specifications 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.14.
www.seagate.com 3.0 Configuring and Mounting the Drive Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
Figure 2 Mounting dimensions (2, 3, 4 & 5TB models) 5.787 in max 146.99 mm 0.138 in 3.51 mm 5 TYP CL OF CONNECTOR DATUM B Temperature Check Point 4.010 in max 101.85 mm 0.814 in 20.68 mm CL OF DRIVE TOP OF LABEL 1.140 ± .050 in 28.96 ± 1.27 mm 1.638 in 41.61 mm 1.22 ± .020 in 30.99 ± .51 mm 0.680 ± .050 in 17.27 ± 1.27 mm 4.00 in 101.60 mm 1.028 in max 26.11 mm 3X 6-32 UNC-2B 3 MIN THREAD DEPTH 0.15 MAX FASTENER PENETRATION MOUNTING HOLES BOTH SIDES Figure 3 3x 0.250 ± .010 in 6.35 ± .
www.seagate.com 4.0 SATA Interface SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6. For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
4.3 Supported ATA commands The following table lists SATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 3.0 (http://www.sata-io.org). See “S.M.A.R.T. commands” on page 25 for details and subcommands used in the S.M.A.R.T. implementation.
www.seagate.com SATA Interface Table 8 SATA standard commands (continued) Command name Command code (in hex) Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable/Disable Autosave B0H / D2H S.M.A.R.T. Enable Operations B0H / D8H S.M.A.R.T.
www.seagate.com 4.3.1 SATA Interface Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on page 19. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
www.seagate.
www.seagate.com SATA Interface Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 84 0 SMART error login is supported. 1 SMART self-test is supported. 2 Media serial number is supported.
www.seagate.com 4.3.2 SATA Interface Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
www.seagate.com 4.3.3 SATA Interface S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100762258, Rev.
