User manual

Using S.M.A.R.T. Disk Monitor 95
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
Compression algorithm : 00000003h, 00000003h, 00000003h
Decompression algorithm : 00000000h, 00000003h, 00000000h
Tape Control : Page [10h] (Factory, Current, Saved)
Change active partition (CAP) : 0, 0, 0
Change active format (CAF) : 0, 0, 0 {R/O}
Active format : 0, 0, 0 {R/O}
Active partition : 0, 0, 0
Write buffer full ratio : 0, 0, 0 {R/O}
Read buffer empty ratio : 0, 0, 0 {R/O}
Write delay time (in 100ms) : 0, 0, 0
Data buffer recovery (DBR) : 0, 0, 0 {R/O}
Block identifiers supported (BIS) : 1, 1, 1 {R/O}
Report setmarks (RSMK) : 1, 1, 1 {R/O}
Automatic velocity control (AVC) : 0, 1, 1
Stop on consecutive filemarks (SOCF) : 0, 0, 0 {R/O}
Recover buffer over (RBO) : 0, 0, 0 {R/O}
Recover error warning (REW) : 0, 0, 0 {R/O}
Gap size : 0, 0, 0 {R/O}
EOD Defined : 0, 0, 0 {R/O}
Enable EOD generation (EEG) : 1, 1, 1 {R/O}
Synchronize early warning (SEW) : 1, 1, 1 {R/O}
Soft write protect (SWP) : 0, 0, 0 {R/O}
Buffer size at early warning : 000000h, 000000h, 000000h
Data compression algorithm : 00h, 00h, 00h
Associated write protect (ASOCWP) : 0, 0, 0 {R/O}
Persistent write protect (PERSWP) : 0, 0, 0 {R/O}
Permanent write protect (PRMWP) : 0, 0, 0 {R/O}
Medium Partition : Page [11h] (Factory, Current, Saved)
Maximum additional partitions : 35, 2, 35
Additional partitions defined : 0, 0, 0
Fixed data partitions (FDP) : 0, 0, 0
Select data partitions (SDP) : 0, 0, 0 {R/O}
Initiator-defined partitions (IDP) : 0, 0, 0
Partition size unit-of-measure (PSUM) : 2, 2, 2
Partition on format (POFM) : 0, 0, 0 {R/O}
CLEAR : 0, 0, 0 {R/O}
ADDP : 0, 0, 0 {R/O}
Medium format recognition : 01h, 01h, 01h
Partition Units : 0, 0, 0
Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)
PERF : 0, 0, 0 {R/O}
EBF : 0, 0, 0 {R/O}
EWASC : 0, 0, 0 {R/O}
DExcpt : 1, 1, 1 {R/O}
TEST : 0, 0, 0
EBACKERR : 0, 0, 0 {R/O}
LogErr : 0, 0, 0 {R/O}
MRIE : 0, 0, 0 {R/O}
Interval timer : 00000000h, 00000000h, 00000000h
Report count : 00000000h, 00000000h, 00000000h
Program Ended.
1.27 Batch Mode Page Import/Export
This feature will save all of the mode pages for a selected device into a file which you can export to one or more
devices with a single command.
Reading Mode Pages and Saving to File
Syntax:smartmon-ux -mpexport FILENAME device
Example: smartmon-ux -mpexport SEAGATEMASTER.TXT /dev/rdsk/c0d0s0
The above will read all mode pages from the selected disk and save it to a file. Note that this is one of the few
commands that will not allow you to enter a list of devices. If you attempt to enter a wild-card for the device that would