User manual

Using S.M.A.R.T. Disk Monitor 209
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
LD[1] State=[INCOMPLETE] RAID-0 DeviceSize=34783232 Blocks
LD[2] State=[OPTIMAL] RAID-1 DeviceSize=17391616 Blocks
LD[3] State=[OPTIMAL] RAID-1 DeviceSize=17391616 Blocks
General Enclosure and State Reporting:
This function decodes and reports the internal event log along with some environmental state information. The state
information will appear first, followed by the event log. The number of environmental lines will vary depending on
whether or not the RAID engine is in a SAF-TE or SES enclosure and/or if those features are enabled. The dump
below was taken from the same engine that we used to report the -zi information above, so you can see the effects of
the failed disks on channel 52h and 5Ah .
All further dumps in this section were run on the same controller.
[root@BOSS smartmon]# ./smartmon-ux -zie /dev/sde
SMARTMon-ux [Release 1.28, Build 01-APR-2005] - Copyright 2001-2005 SANtools, Inc. http://www.SANtools.com
Discovered IFT ER2000R1 S/N "3221234" on /dev/sde (SMART unsupported)(492 MB)
Redundant controller configuration: Primary
Redundant controller status: Scanning
Original controller role: Secondary
Current controller role: Secondary
UPS status: OK
Information [#1 Type 0181h at 18:28:13 03/29/2005] Controller initialization complete on Primary controller.
Alert [#2 Type 0124h at 18:31:18 03/29/2005] UPC AC power loss detected on Primary controller.
Warning [#3 Type 113Fh at 18:38:58 03/29/2005] Channel 0 reported that a redundant loop failure has been
detected. Now using the surviving logical channel 2.
Warning [#4 Type 113Fh at 18:52:58 03/29/2005] Channel 0 reported that a redundant loop failure has been
detected. Now using the surviving logical channel 2.
Warning [#5 Type 113Fh at 18:54:57 03/29/2005] Channel 1 (ID 82/52h) reported that a redundant path failure
was detected. Now using redundant logical channel 1.
Warning [#6 Type 1101h at 18:55:01 03/29/2005] Channel 1 (ID 82/52h) reported a select timeout, sector=0h.
Alert [#7 Type 2101h at 18:55:02 03/29/2005] SCSI drive failed on logical drive 0(channel=1, id=82/52h,
lun=0).
Warning [#8 Type 113Fh at 19:01:45 03/29/2005] Channel 1 (ID 89/59h) reported that a redundant path failure
was detected. Now using redundant logical channel 1.
Warning [#9 Type 1101h at 19:01:45 03/29/2005] Channel 1 (ID 89/59h) reported a select timeout, sector=0h.
Warning [#10 Type 113Fh at 19:12:49 03/29/2005] Channel 1 (ID 86/56h) reported that a redundant path failure
was detected. Now using redundant logical channel 1.
Warning [#11 Type 1101h at 19:12:49 03/29/2005] Channel 1 (ID 86/56h) reported a select timeout, sector=0h.
Alert [#12 Type 2101h at 19:12:50 03/29/2005] SCSI drive failed on logical drive 0(channel=1, id=86/56h,
lun=0).
Warning [#13 Type 113Fh at 19:13:26 03/29/2005] Channel 1 (ID 90/5ah) reported that a redundant path failure
was detected. Now using redundant logical channel 1.
Warning [#14 Type 1101h at 19:13:26 03/29/2005] Channel 1 (ID 90/5ah) reported a select timeout, sector=0h.
Alert [#15 Type 2101h at 19:13:27 03/29/2005] SCSI drive failed on logical drive 0(channel=1, id=90/5ah,
lun=0).
Information [#16 Type 2183h at 19:13:42 03/29/2005] Rebuild continued on logical drive 0.
Information [#17 Type 2184h at 19:23:58 03/29/2005] Rebuild paused due to state change on logical drive 0.
Information [#18 Type 113Fh at 21:08:50 03/29/2005] Channel 0 reported that the fibre loop connection has
been restored.
Full RAID Controller Event Log:
The -ziL option returns basically the same results as the -zie option, but it does not report any enclosure information.
This option only reports the event log.
[root@BOSS smartmon]# ./smartmon-ux -ziL /dev/sde
SMARTMon-ux [Release 1.28, Build 01-APR-2005] - Copyright 2001-2005 SANtools, Inc. http://www.SANtools.com
Discovered IFT ER2000R1 S/N "3221234" on /dev/sde (SMART unsupported)(492 MB)
Information [#1 Type 0181h at 18:28:13 03/29/2005] Controller initialization complete on Primary controller.
Alert [#2 Type 0124h at 18:31:18 03/29/2005] UPC AC power loss detected on Primary controller.
Warning [#3 Type 113Fh at 18:38:58 03/29/2005] Channel 0 reported that a redundant loop failure has been
detected. Now using the surviving logical channel 2.
Warning [#4 Type 113Fh at 18:52:58 03/29/2005] Channel 0 reported that a redundant loop failure has been
detected. Now using the surviving logical channel 2.
Warning [#5 Type 113Fh at 18:54:57 03/29/2005] Channel 1 (ID 82/52h) reported that a redundant path failure
was detected. Now using redundant logical channel 1.
Warning [#6 Type 1101h at 18:55:01 03/29/2005] Channel 1 (ID 82/52h) reported a select timeout, sector=0h.
208 208