User manual

Using S.M.A.R.T. Disk Monitor 57
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
SAF-TE Enclosure services available: NO
VS bit (byte #6/bit #5 set): NO
VS bit (byte #7/bit #0 set): NO
Capstan motor assembly rev: L
Step motor assembly rev: C
Cartridge manipulation motor rev: 0
Sensor assembly rev: A
Mainboard assembly rev: D
Frame module rev: 2
Head assembly rev: 0
Top cover rev: 0
Bridge module rev: 0
Main spring module rev: 1
Main microcode rev: 0483
Main microcode release status: D
Main microcode branch rev: 0000
Main microcode ID: =
DSP microcode rev level: 0483
DSP microcode release status: ..
Drive manufacturing MM.DD.YY: 06.12.01
Main microcode creation MM.DD.YY: 07.03.01
DSP microcode creation MM.DD.YY: 07.03.01
Last drive adjustment MM.DD.YY: ........
Inquiry Page Hex Dump:
0000: 01 80 02 02 2B 00 01 38 54 41 4E 44 42 45 52 47 ....+..8TANDBERG
0010: 53 4C 52 37 20 20 20 20 20 20 20 20 20 20 20 20 SLR7
0020: 30 34 38 33 44 30 30 30 30 3D 20 30 34 38 33 0483D0000= 0483
Inquiry EVPD Page #80h (Serial Number Page)
0000: 01 80 00 0C 53 4E 30 30 37 30 30 35 33 39 36 00 ....SN007005396.
Inquiry EVPD Page #81h
0000: 01 81 00 02 03 03 ......
Inquiry EVPD Page #82h (Operating Definition Page)
0000: 01 82 00 14 13 53 43 53 49 2D 32 20 58 33 2E 31 .....SCSI-2 X3.1
0010: 33 31 2D 31 39 39 34 00 31-1994.
Inquiry EVPD Page #C0h
0000: 01 C0 00 17 20 4C 20 43 20 30 20 41 20 44 20 32 .À.. L C 0 A D 2
0010: 20 30 20 30 20 30 20 31 20 32 00 0 0 0 1 2.
Inquiry EVPD Page #C1h
0000: 01 C1 00 11 30 34 38 33 44 30 30 30 30 3D 20 30 .Á..0483D0000= 0
0010: 34 38 33 44 00 483D.
Inquiry EVPD Page #C2h
0000: 01 C2 00 09 30 36 2E 31 32 2E 30 31 00 .Â..06.12.01.
Inquiry EVPD Page #C3h
0000: 01 C3 00 12 30 37 2E 30 33 2E 30 31 2F 30 37 2E .Ã..07.03.01/07.
0010: 30 33 2E 30 31 00 03.01.
Inquiry EVPD Page #C4h
0000: 01 C4 00 09 FF FF FF FF FF FF FF FF 00 .Ä..ÿÿÿÿÿÿÿÿ.
As you can see, the Seagate disk drive and the Tandberg tape drive have a lot of information to report. You can get
part and serial numbers for individual drive components, firmware revisions, world-wide-name, and hundreds of other
fields. You should also be aware that many fields are vendor-specific. This means their record layouts are not
standardized by the ANSI committee, so you will need to contact Seagate to obtain this information. Please contact
your manufacturer to obtain the layouts, and/or view their web sites. All of this information is usually online.
If you had just entered the -I option, you would have gotten same results, without the EVPD page hex dumps, and
without the fields which appear after the defects. In the dump above, the fields in blue will only be reported with the -
I+ command as they come from the EVPD pages.
Fibre Channel disk drives will also report the World Wide Name (also called the IEEE Device ID). If the above disk
was a fibre channel disk, then a line such as the one below would be added to the report under Board Serial Number.
This was added in release 1.30.
IEEE Unique ID: 20-00-00-11-C6-B5-64-45
Additionally, if you have an IDE disk drive and are running a distribution that supports IDE drives, you might see
similar results from supplying the -I+ option:
The output below is from an SATA (ATA-7 type) drive. Each version of the ATA specification has some fields which
have either been added or deleted from previous versions. In addition, some fields are specific to serial ATA (SATA)