User manual

SANtools® S.M.A.R.T. Disk Monitor (SMARTMon-UX)86
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
ADDP : 0 {R/O}
Medium format recognition : 03h
Partition Units : 0 {R/O}
Terminating program.
For comparison, this is part of what a Seagate FC disk drive returned for the protocol-specific mode page 19 as
shown from
the output for version 1.35 of the software.
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : Fibre Channel
Disable target orig loopid (DTOLI) : 1, 1, 1
Disable target init porten (DTIPE) : 0, 0, 0
Allow login w/o loop init (ALWLI) : 1, 1, 1
Require hard address (RHA) : 1, 1, 1
Disable loop master (DLM) : 1, 1, 1
Disable discovery (DDIS) : 0, 0, 0
Prevent loop port bypass (PLPB) : 0, 0, 0
Disable fabric discovery (DTFD) : 0, 0, 0
Resource recov timeout granularity : 0, 0, 0 {R/O}
Resource recovery timeout : 0, 0, 0 {R/O}
1.26.1 Example Mode Page Dump - SAS Disk
The results below were run under SPARC Solaris 10 using a Seagate ST3146855SS SAS disk.
# /etc/smartmon-ux -J /dev/rdsk/c4t17d0s0
SMARTMon-UX [Release 1.36, Build 8-JUN-2008] - Copyright 2001-2008 SANtools(R), Inc. http://www.SANtools.
com
Discovered SEAGATE ST3146855SS S/N "3LN29QG4" on /dev/rdsk/c4t17d0s0 (SMART enabled)(140014 MB)
Read-Write Error Recovery : Page [01h] (Factory, Current, Saved)
Automatic reallocation of write (AWRE) : 1, 1, 1
Automatic reallocation of read (ARRE) : 1, 1, 1
Transfer block (TB) : 0, 0, 0
Read continuous (RC) : 0, 0, 0
Enable early recovery (EER) : 0, 0, 0
Post error (PER) : 1, 1, 1
Disable transfer on error (DTE) : 0, 0, 0
Disable correction (DCR) : 0, 0, 0
Read Retry Count : 11, 11, 11
Correction Span : 255, 255, 255 {R/O}
Head Offset Count : 0, 0, 0 {R/O}
Data Strobe Offset Count : 0, 0, 0 {R/O}
Write Retry Count : 5, 5, 5
Recovery Time Limit : 65535, 65535, 65535
Disconnect-Reconnect : Page [02h] (Factory, Current, Saved)
Buffer full ratio : 0, 0, 0 {R/O}
Buffer empty ratio : 0, 0, 0 {R/O}
Bus inactivity limit : 0, 0, 0 {R/O}
Disconnect time limit : 0, 0, 0 {R/O}
Connect time limit : 0, 0, 0 {R/O}
Maximum burst size : 164, 164, 164
Enable modify data pointers (EMDP) : 0, 0, 0 {R/O}
Fair arbitration : 0, 0, 0 {R/O}
Disconnect immediate (DImm) : 0, 0, 0 {R/O}
Data transfer disconnect control (DTDC) : 0, 0, 0 {R/O}
First burst size : 0, 0, 0 {R/O}
Format Device : Page [03h] (Factory, Current, Saved)
Tracks per zone : 13356, 13356, 13356 {R/O}
Alternate sectors per zone : 0, 0, 0 {R/O}
Alternate tracks per zone : 28, 28, 28 {R/O}
Alternate tracks per lun : 0, 0, 0 {R/O}
Sectors per track : 987, 987, 987 {R/O}
Bytes per sector : 512, 512, 512 {R/O}
Interleave : 1, 1, 1 {R/O}