User manual

SANtools® S.M.A.R.T. Disk Monitor (SMARTMon-UX)88
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
Extended self-test completion time : 0, 0, 0
Protocol : Page [18h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Transport layer retries : 0, 0, 0 {R/O}
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Ready LED meaning : 0, 0, 0
I_T nexus loss time (ms) : 2000, 2000, 2000
Initiator response timeout (ms) : 0, 0, 0
PHY identifier #0 : 00h, 00h, 00h
(0)Attached device type : 2, 2, 2 {R/O}
(0)Negotiated link rate : 9, 9, 9 {R/O}
(0)SSP initiator port # : 0, 0, 0 {R/O}
(0)STP initiator port # : 0, 0, 0 {R/O}
(0)SMP initiator port # : 1, 1, 1 {R/O}
(0)SSP target port # : 0, 0, 0 {R/O}
(0)STP target port # : 0, 0, 0 {R/O}
(0)SMP target port # : 1, 1, 1 {R/O}
(0)SAS Address : 5000C5000694BFFDh, 5000C5000694BFFDh, 5000C5000694BFFDh
(0)Attached SAS address : 500A0B82E0894000h, 500A0B82E0894000h, 500A0B82E0894000h
(0)Attached PHY identifier : 0Bh, 0Bh, 0Bh
(0)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(0)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(0)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
(0)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
PHY identifier #1 : 01h, 01h, 01h
(1)Attached device type : 2, 2, 2 {R/O}
(1)Negotiated link rate : 9, 9, 9 {R/O}
(1)SSP initiator port # : 0, 0, 0 {R/O}
(1)STP initiator port # : 0, 0, 0 {R/O}
(1)SMP initiator port # : 1, 1, 1 {R/O}
(1)SSP target port # : 0, 0, 0 {R/O}
(1)STP target port # : 0, 0, 0 {R/O}
(1)SMP target port # : 1, 1, 1 {R/O}
(1)SAS Address : 5000C5000694BFFEh, 5000C5000694BFFEh, 5000C5000694BFFEh
(1)Attached SAS address : 500A0B82E0850000h, 500A0B82E0850000h, 500A0B82E0850000h
(1)Attached PHY identifier : 0Bh, 0Bh, 0Bh
(1)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(1)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(1)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
(1)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
Power Condition : Page [1Ah] (Factory, Current, Saved)
Idle : 0, 0, 0
Standby : 0, 0, 0
Idle condition timer : 00000005h, 00000005h, 00000005h
Standby condition timer : 00000004h, 00000004h, 00000004h
Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)
PERF : 1, 0, 0
EBF : 0, 0, 0 {R/O}
EWASC : 1, 1, 1
DExcpt : 0, 0, 0
TEST : 0, 0, 0
EBACKERR : 0, 0, 0 {R/O}
LogErr : 0, 0, 0
MRIE : 4, 6, 6
Interval timer : 00000000h, 00001770h, 00001770h
Report count : 00000001h, 00000000h, 00000000h
Background scanning configuration : Page [1Ch,1] (Factory, Current, Saved)
Bkgrnd suspend on log full (S_L_FULL) : 0, 0, 0 {R/O}
Bkgrnd log only intervention (LOWIR) : 0, 0, 0 {R/O}
Bkgrnd enable medium scan (EN_BMS) : 1, 1, 1 {R/O}
Bkgrnd enable pre-scan (EN_PS) : 0, 0, 0 {R/O}
Bkgrnd medium scan interval (hrs) : 168, 24, 24