User manual

SANtools® S.M.A.R.T. Disk Monitor (SMARTMon-UX)90
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
Medium rotation Rate : 10016, 10016, 10016 {R/O}
Verify Error Recovery : Page [07h] (Factory, Current, Saved)
EER : 0, 0, 0
PER : 0, 0, 0
DTE : 0, 0, 0
DCR : 0, 0, 0
Verify Retry Count : 11, 11, 11
Verify Correction Span (bits) : 240, 240, 240 {R/O}
Verify Recovery Time Limit (ms) : 65535, 65535, 65535
Cache Control : Page [08h] (Factory, Current, Saved)
Initiator control (IC) : 0, 0, 0
Abort Pre-fetch (ABPF) : 0, 0, 0 {R/O}
Caching analysis permitted (CAP) : 0, 0, 0
Discontinuity (DISC) : 1, 0, 0
Size enable (Size) : 0, 0, 0 {R/O}
Write cache enable (WCE) : 1, 1, 1
Multiplication factor (MF) : 0, 0, 0 {R/O}
Read cache disable (RCD) : 0, 0, 0
Demand read retention priority : 0, 0, 0 {R/O}
Demand Write Retention Priority : 0, 0, 0 {R/O}
Disable Pre-fetch Transfer Length : 65535, 65535, 65535 {R/O}
Minimum Pre-fetch : 0, 0, 0
Maximum Pre-fetch : 65535, 0, 0
Maximum Pre-fetch Ceiling : 65535, 65535, 65535 {R/O}
Force sequential write (FSW) : 1, 0, 0
LB cache segment size (LBCSS) : 0, 0, 0 {R/O}
Disable read-ahead (DRA) : 0, 0, 0
Vendor-specific bits (VSS) : 0, 0, 0 {R/O}
Number of cache segments : 16, 24, 24
Cache segment size : 0, 0, 0 {R/O}
Non cache segment size : 0, 0, 0 {R/O}
Control Mode : Page [0Ah] (Factory, Current, Saved)
TST : 0, 0, 0 {R/O}
TMF_ONLY : 0, 0, 0 {R/O}
D_SENSE : 0, 0, 0 {R/O}
GLTSD : 1, 0, 0
RLEC : 0, 0, 0
Queue algorithm modifier : 0, 0, 0
QErr : 0, 0, 0 {R/O}
DQue : 0, 0, 0
VS : 0, 0, 0 {R/O}
RAQ : 0, 0, 0 {R/O}
UA_INTLCK_CTRL : 0, 0, 0 {R/O}
SWP : 0, 0, 0
RAERP : 0, 0, 0 {R/O}
UUAERP : 0, 0, 0 {R/O}
EAERP : 0, 0, 0 {R/O}
ATO : 0, 0, 0 {R/O}
TAS : 0, 0, 0 {R/O}
Autoload mode : 0, 0, 0 {R/O}
Ready AER holdoff period : 0, 0, 0 {R/O}
Busy timeout period : 0, 0, 0 {R/O}
Extended self-test completion time : 1350, 1350, 1350 {R/O}
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : Fibre Channel
Disable target orig loopid (DTOLI) : 0, 0, 0
Disable target init porten (DTIPE) : 0, 0, 0
Allow login w/o loop init (ALWLI) : 0, 0, 0
Require hard address (RHA) : 0, 0, 0
Disable loop master (DLM) : 0, 0, 0
Disable discovery (DDIS) : 0, 0, 0
Prevent loop port bypass (PLPB) : 0, 1, 1
Disable fabric discovery (DTFD) : 0, 0, 0
Resource recov timeout granularity : 0, 0, 0 {R/O}
Resource recovery timeout : 0, 0, 0 {R/O}
Power Condition : Page [1Ah] (Factory, Current, Saved)