User manual

Using S.M.A.R.T. Disk Monitor 93
SANTOOLS® is registered in US Patent and Trademark Office No 3,107,854 All rights reserved.
EAERP : 0, 0, 0 {R/O}
ATO : 0, 0, 0 {R/O}
TAS : 0, 0, 0 {R/O}
Autoload mode : 0, 0, 0 {R/O}
Ready AER holdoff period : 0, 0, 0 {R/O}
Busy timeout period : 0, 0, 0 {R/O}
Extended self-test completion time : 984, 984, 984 {R/O}
Notch and Partition : Page [0Ch] (Factory, Current, Saved)
Notched Drive (ND) : 1, 1, 1 {R/O}
Logical or Physical Notch (LPN) : 0, 0, 0
Max # of notches : 18, 18, 18 {R/O}
Active Notch : 0, 0, 0
Starting Boundary : 00000000h, 00000000h, 00000000h
Ending Boundary : 00C00501h, 00C00501h, 00C00501h
Pages notched : 0000000000000008h, 0000000000000008h, 0000000000000008h
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : Parallel SCSI
Driver strength : 1, 1, 1 {R/O}
Driver asymmetry : 0, 0, 0 {R/O}
Driver precompensation : 0, 0, 0 {R/O}
Driver slew rate : 0, 0, 0 {R/O}
DB(0) Value : 0, 0, 0 {R/O}
DB(1) Value : 0, 0, 0 {R/O}
DB(2) Value : 0, 0, 0 {R/O}
DB(3) Value : 0, 0, 0 {R/O}
DB(4) Value : 0, 0, 0 {R/O}
DB(5) Value : 0, 0, 0 {R/O}
DB(6) Value : 0, 0, 0 {R/O}
DB(7) Value : 0, 0, 0 {R/O}
DB(8) Value : 0, 0, 0 {R/O}
DB(9) Value : 0, 0, 0 {R/O}
DB(10) Value : 0, 0, 0 {R/O}
DB(11) Value : 0, 0, 0 {R/O}
DB(12) Value : 0, 0, 0 {R/O}
DB(13) Value : 0, 0, 0 {R/O}
DB(14) Value : 0, 0, 0 {R/O}
P_CRCA : 0, 0, 0 {R/O}
P1 : 0, 0, 0 {R/O}
BSY : 0, 0, 0 {R/O}
SEL : 0, 0, 0 {R/O}
RST : 0, 0, 0 {R/O}
REQ : 0, 0, 0 {R/O}
ACK : 0, 0, 0 {R/O}
ATN : 0, 0, 0 {R/O}
C/D : 0, 0, 0 {R/O}
I/O : 0, 0, 0 {R/O}
MSG : 0, 0, 0 {R/O}
Transfer period factor : 0, 0, 0 {R/O}
REQ/ACK offset timing : 0, 0, 0 {R/O}
Transfer width exponent : 1, 1, 1 {R/O}
Protocol options bits : 09h, 09h, 09h
Driver asymmetry : 0, 0, 0 {R/O}
Sent PCOMP enabled : 0, 0, 0 {R/O}
Received PCOMP enabled : 0, 0, 0 {R/O}
Min xfr period factor : 0, 0, 0 {R/O}
Max REQ/ACK offset : 0, 0, 0 {R/O}
Max transfer width exponent : 1, 1, 1 {R/O}
Protocol options bits supported : 08h, 08h, 08h
Power Condition : Page [1Ah] (Factory, Current, Saved)
Idle : 0, 0, 0
Standby : 0, 0, 0
Idle condition timer : FFFFFFFFh, FFFFFFFFh, FFFFFFFFh
Standby condition timer : FFFFFFFFh, FFFFFFFFh, FFFFFFFFh
Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)
PERF : 0, 0, 0
EBF : 0, 0, 0
EWASC : 1, 1, 1