• • • • • • • • • • • • • • • • • • • • • • • • • • Cheetah 9LP • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Disc Drive • • • • • • • • • ST39102LW/LC • • • • • • • • • • • • • ST34502LW/LC • • • • • • • • • • • • • Installation Guide • • • • • • • • • • • • • • •
Contents Preface ..................................................................................... 1 Electrostatic discharge protection ............................................ 1 Important safety information and precautions .......................... 2 Wichtige Sicherheitshinweise ................................................... 4 Regulatory agency compliance ................................................ 7 Seagate Technology support services......................................
Cheetah 9LP Installation Guide, Rev. B 1 Preface This manual contains information for users of the Seagate® Cheetah 9LP SCSI disc drives. It provides support services, performance specifications, and initial setup information. Additional information is available in the Cheetah 9LP Product Manual (part number 83329240). Contact your Seagate sales representative if you need to order this publication. Electrostatic discharge protection Caution.
2 Cheetah 9LP Installation Guide, Rev. B • Turn off the power before removing or installing the DC power cable. • Do not remove any circuit boards from the drive. • Never use an ohmmeter on any circuit boards. • When installing the drive on a carrier or tray, discharge the carrier or tray prior to inserting it into the system. Important safety information and precautions Caution. Use forced-air ventilation when bench-testing the drive to ensure proper cooling of drive components.
Cheetah 9LP Installation Guide, Rev. B • • • • 3 stacked vertically, pay special attention to the top where temperatures are usually highest. Follow the precautions listed above in “Electrostatic discharge protection.” Do not remove any circuit boards from the drive. Return the entire drive for depot repair if any circuit board is defective. Removal of circuit boards by personnel not performing depot repair will damage components and may void the warranty.
4 Cheetah 9LP Installation Guide, Rev. B This unit is a component part and as such is not meant to comply with FCC or similar national requirements as a stand-alone unit. Engineering radiated emissions test results are available through the Seagate Safety Department to assist the subsystem designer. Wichtige Sicherheitshinweise Vorsicht. Beim Testen des Laufwerks auf dem Prüftisch ist Fremdbelüftung vorzusehen, um eine ausreichende Kühlung der Laufwerkkomponenten sicherzustellen.
Cheetah 9LP Installation Guide, Rev. B 5 Beachten Sie in jedem Fall die folgenden Warn-und Vorsichtshinweise: • Beachten Sie alle Warn- und Vorsichtshinweise in diesem Handbuch. • Treffen Sie beim Betrieb, bei der Installation oder bei der Entfernung der Einheit angemessene Sicherheitsvorkehrungen. • Wenn eine Einheit unter Spannung steht, gehen Sie bei der Fehlerdiagnose besonders vorsichtig vor. Schalten Sie die Einheit aus, bevor Sie mit den Installations-und Entfernungsarbeiten beginnen.
6 Cheetah 9LP Installation Guide, Rev. B • Die vormontierte Kopf- und Festplatteneinheit (HDA) nicht aus dem Laufwerkgehäuse nehmen! Falls die HDA beschädigt ist, schicken Sie das gesamte Laufwerk zur Reparatur ein. • Die HDA ist nicht vor Ort reparierbar und darf nicht auseinandergenommen werden! Öffnen der versiegelten HDA durch andere Personen als die für die werkseitige Reparatur zuständigen hat eine Beschädigung der Komponenten und Erlöschen des Garantieanspruchs zur Folge.
Cheetah 9LP Installation Guide, Rev. B 7 magnetische Strahlung sind für Designer von Untersystemen auf Anfrage von der Seagate-Sicherheitsabteilung erhältlich. Regulatory agency compliance Electromagnetic susceptibility As a component assembly, the drive is not required to meet any susceptibility performance requirements.
8 Cheetah 9LP Installation Guide, Rev. B shall confirm EMC compliance and provide CE Marking and CTick Marking for their product. Electromagnetic compliance for the European Union If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/336/EEC of 03 May 1989 as amended by Directive 92/31/ EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993.
Cheetah 9LP Installation Guide, Rev. B 9 Seagate Technology support services Presales support To determine which Seagate products are best suited for your specific application, contact us about configuration and compatibility and for current product availability. You can leave a voice message after business hours or send an e-mail message—we reply during business hours. Disc Drives 405-936-1210 Fax: 405-936-1683 (8:00 A.M. to 12:15 P.M., 1:30 P.M. to 6:00 P.M.
10 Cheetah 9LP Installation Guide, Rev. B asked questions, troubleshooting tips, and specifications for disc drives and tape drives. This service is available 24 hours daily and requires a touch-tone phone. International callers can reach this automated self-help service by dialing 405-936-1234. Online services Using a modem, you can obtain troubleshooting tips, free utility programs, drive specifications and jumper settings for Seagate’s entire product line.
Cheetah 9LP Installation Guide, Rev. B Location Phone number UK USA 44-1628-478011 Disc: 405-936-1600; Tape: 405-936-1630 11 FAX services SeaFAX® You can use a touch-tone telephone to access Seagate’s automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily.
12 Cheetah 9LP Installation Guide, Rev. B Location Phone number UK USA 44-1628-890660 Disc: 405-936-1685; Tape: 405-936-1683 Direct-support services Technical support For one-on-one help, you can talk to a technical support specialist during local business hours. Before calling, note your system configuration and drive model number (ST xxxx). Location Phone number Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., eastern time, M–F) 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M.
Cheetah 9LP Installation Guide, Rev. B 13 SeaTDD™ 405-936-1687 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange messages with a technical support specialist between 8:00 A.M. to 12:15 P.M. and 1:30 P.M. to 6:00 P.M. (central time) Monday through Friday. Customer service centers Seagate direct OEM, Distribution, and Systems Integrator customers should contact their Seagate service representative for warranty information.
14 Cheetah 9LP Installation Guide, Rev.
Cheetah 9LP Installation Guide, Rev. B 15 General description Cheetah 9LP SCSI disc drives are high-speed, random-access digital-data storage devices capable of operating in single-ended (SE) or low voltage differential (LVD) modes. These two modes are offered to allow you to use this drive in systems that use the traditional SE technology or to use it in LVD-capable systems. Refer to page 20 for additional information about LVD technology.
16 Cheetah 9LP Installation Guide, Rev. B Figure 1.
Cheetah 9LP Installation Guide, Rev. B Characteristics ST39102LW/LC SCSI1 17 ST34502LW/LC Ultra2 SCSI1 Interface Ultra2 Capacity Unformatted (Gbytes) Formatted (Gbytes)2 11.27 9.17 5.63 4.55 Recording Cylinders (user) Read/write data heads Avg bytes/track 6,962 12 104,840-159,008 6,962 6 104,840-159,008 Access time3 Average read (msec) Average write (msec) 5.4 6.2 5.4 6.2 Disc rotation RPM Average latency (msec) 10,025 2.99 10,025 2.
18 Cheetah 9LP Installation Guide, Rev. B Single-ended (SE) mode Low voltage differential (LVD) mode DC power requirements (±5%)1 +5 V +12 V +5 V +12 V ST39102LW/LC Maximum start current Maximum operating current Average idle current 0.94A 1.02A 0.78A 1.7A 0.84A 0.60A 0.96A 1.09A 0.80A 1.7A 0.84A 0.60A ST34502LW/LC Maximum start current Maximum operating current Average idle current 0.84 0.85 0.71 1.7 0.60 0.39 0.86 0.93 0.73 1.7 0.60 0.39 1.
Cheetah 9LP Installation Guide, Rev. B 19 Initial setup information The general information beginning on this page applies to all of the Cheetah 9LP drive models. After reading the general information topics, refer to the appropriate drive-specific section listed below for additional information about configuring and installing your particular model.
20 Cheetah 9LP Installation Guide, Rev. B Single-ended and low voltage differential modes This drive incorporates two different transceivers to allow you to use it in traditional systems which may use single-ended (SE) drivers and receivers, or to use it in low voltage differential (LVD) capable systems which use LVD drivers and receivers. You can configure the drive to switch between SE and LVD modes automatically or force it to operate in SE mode only.
Cheetah 9LP Installation Guide, Rev. B 21 SCSI IDs are normally used for other SCSI devices such as this Cheetah disc drive. Note. Most SCSI controllers (host adapters) allow you to skip a SCSI ID. For example, you can have ID0, ID1, and ID3 (skipping ID2). Other controllers do not allow this so be sure to refer to your system or controller user’s manual for details about its requirements for proper SCSI device installation. Note. This drive is SCAM (SCSI Configured Auto Magically) compliant.
22 Cheetah 9LP Installation Guide, Rev. B Drive termination If you are installing a Cheetah drive in a system that has other SCSI devices installed, terminate only the end devices on the SCSI chain. A SCSI “device” is any disc drive, scanner, tape backup unit, or other piece of hardware connected to your system using the SCSI bus. Note. Use active (ANSI SCSI-2 Alternative 2) single-ended terminators when terminating a bus operating in singleended mode.
Cheetah 9LP Installation Guide, Rev. B 23 plished by terminating the bus at the backpanel. For ST39102LW and ST34502LW drives, use an in-line terminator on the cable. Internal SCSI cable Internal SCSI device Internal SCSI device Controller Terminate Internal SCSI cable Internal SCSI device Internal SCSI device Controller External SCSI cable External SCSI device External SCSI device Terminate Figure 2.
24 Cheetah 9LP Installation Guide, Rev. B use these wide drives on a standard (non-wide) 8-bit data bus if you provide proper termination to the upper 8-bit data lines. This is often referred to as providing “high-9 termination.” Figures 3, 4, and 5 show typical drive connections. The following table lists the maximum cable lengths and number of devices using single-ended and LVD I/O circuits allowed on a daisy-chain cable for 10, 20, and 40 Mtransfers/sec I/O data transfer rates. Table 1.
Cheetah 9LP Installation Guide, Rev. B Figure 3. 68-pin I/O connection to drive (LW model) Figure 4.
26 Cheetah 9LP Installation Guide, Rev. B “LW” Model Drive Note: Do not mix “LW” and “WD” model drives on the daisy chain. Terminator [2] 2 through X SCSI devices [1] Pin 1 (check your adapter for Pin 1 location) SCSI ID 1 SCSI ID 7 SCSI ID 0 Terminated Host Adapter PCB [1] “X” means up to 15 or the maximum allowable number of devices on the SCSI bus. See system documentation and Table 1. [2] External terminator. Used only on end “LW” drive.
Cheetah 9LP Installation Guide, Rev. B 27 80-pin SCSI I/O Connector Pin 1 J2 J6 Note. This drive model plugs directly into a backplane connector and therefore uses no cables. Figure 6.
28 Cheetah 9LP Installation Guide, Rev. B Providing adequate cooling The enclosure design must ensure adequate cooling for the drive. The maximum ambient temperature allowed is 50°C. The drive’s product manual (83329240) describes how to evaluate the air-flow design. The evaluation consists of ensuring that the case temperature of certain critical components remains within acceptable limits during drive operation.
Cheetah 9LP Installation Guide, Rev. B 29 Kühlung des Systems Die Gehäusekonstruktion muß eine ausreichende Kühlung des Laufwerkes gewährleisten. Die Umgebungstemperatur darf maximal 50°C betragen. Die Produkthandbuch Cheetah 9LP (Dokument 83329240) enthalten Anweisungen zur Beurteilung der Luftstromkonstruktion. Die Beurteilung muß sicherstellen, daß sich die Gehäuset e m p e r a t u r b e s t i m m t e r k r i t i s c h e r Ko m p o n e n t e n b e i Laufwerkbetrieb innerhalb zugelassener Grenzen hält.
30 Cheetah 9LP Installation Guide, Rev. B . Above unit Note. Air flows in the direction shown (back to front) or in reverse direction (front to back) Under unit Above unit Note. Air flows in the direction shown or in reverse direction (side to side) Under unit Figure 7. Suggested air flow Abbildung 7.
Cheetah 9LP Installation Guide, Rev. B 31 Mounting the drive and connecting cables Do not touch the connector pins or any components on the control board without observing static-discharge precautions. Always handle the drive by the frame only. The drive may be mounted in any orientation (horizontally, vertically, and any combination thereof); however, you must ensure that the drive receives adequate air flow for cooling. 1. Mount the drive to the host system’s chassis using four 6-32 UNC screws.
32 Cheetah 9LP Installation Guide, Rev. B 1. Befestigen Sie das Laufwerk mit vier 6-32-UNC-Schrauben am Gehäuse des Host-Systems. Die beiden Seiten des Laufwerkes sind mit jeweils zwei Befestigungslöchern versehen, die Unterseite des Laufwerkes weist vier weitere Befestigungslöcher auf. Gemessen von der Außenfläche des Gehäuses dürfen die Schrauben maximal 3,81 mm in die Befestigungslöcher des Gehüuses hineinragen. Die Schrauben müssen gleichmäßig, jedoch nicht zu fest, angezogen werden.
Cheetah 9LP Installation Guide, Rev. B 33 defined in IEC 950. Figure 8 provides the pin information for the DC power connector. To connect the DC power cable to the drive, simply insert the cable end into the drive’s DC power connector. 4. Schließen Sie das SCSI-Kabel an den SCSI-Steckverbinder des Laufwerkes an. Das Kabel darf nicht gedehnt oder gedrückt werden und es darf den Luftstrom zur Kühlung des Systems nicht behindern.
34 Cheetah 9LP Installation Guide, Rev. B Note. Signal ground on the power control board (PCB) and the head and disc assembly (HDA) are connected together in this drive and you cannot separate them. The equipment in which you have mounted the drive is connected directly to the HDA and PCB without electrically isolating shock mounts. Maximizing the conductive contact area between HDA ground and system ground may reduce radiated emissions.
Cheetah 9LP Installation Guide, Rev. B 35 elektromagnetische Strahlung fällt in den Zuständigkeitsbereich des Systemdesigners. 5. Replace the host system’s cover. 5. Setzen Sie das Gehäuseoberteil des Host-Systems wieder auf.
36 Cheetah 9LP Installation Guide, Rev. B K // T -Z- S [1] H -Z- L J B R Notes: [1] Mounting holes are 6-32 UNC 2B, three on each side and four on the bottom. Max screw penetration into side of drive is 0.15 in. (3.81 mm). Max screw tightening torque is 6.0 in-lb (3.32 nm) with minimum full thread engagement of 0.12 in. (3.05 mm). A -ZM U -X- A B C D E F G H J K L M Dimension Table Millimeters Inches 26.10 max 1.028 max 147.00 max 5.787 max 101.60 ± .25 4.000 ± .010 92.25 ± .25 3.750 ± .010 3.
Cheetah 9LP Installation Guide, Rev. B 37 K // T -Z- S [1] H -Z- L J B R N -Z- -XA -ZM Notes: [1] Mounting holes are 6-32 UNC 2B, three on each side and four on the bottom. Max screw penetration into side of drive is 0.15 in. (3.81 mm). Max screw tightening torque is 6.0 in-lb (3.32 nm) with minimum full thread engagement of 0.12 in. (3.05 mm). U -X- P G A B C D E F G H J K L M N P R S T U [1] F E Dimension Table Millimeters Inches 26.10 max 1.028 max 147.00 max 5.787 max 101.60 ± .25 4.000 ± .
38 Cheetah 9LP Installation Guide, Rev. B Formatting the drive The drive has been low level formatted at the factory. You do not need to perform another low level format on this drive unless you decide to perform certain diagnostics through the host adapter. If you do decide to perform a low level format, do not abort the format as this is likely to make the drive inoperable. Also, it is a good idea to protect against power failure or other power interruptions during the format.
Cheetah 9LP Installation Guide, Rev. B 39 capacity drives. Refer to your system or utility manual for detailed instructions. • DOS/Windows 3.1/Windows 95. Set the drive type in CMOS to “Zero,” “None,” or “No hard drive installed.” Use FDISK.EXE and FORMAT.EXE. • Macintosh. Use a third-party drive utility or Apple’s Drive Setup (version 1.3.1 or later) to initialize the drive. Note: versions of Apple Drive Setup prior to version 1.3.1 do not recognize nonApple drives.
40 Cheetah 9LP Installation Guide, Rev. B LW drives Setting the SCSI IDLW jumpers drives section Use the J6 connector to set the SCSI ID (see Figure 11). To change the SCSI ID, install jumpers as shown in the illustration. Drive Front Jumper Plug (enlarged to show detail) Pin 1 J6 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15 Figure 11.
Cheetah 9LP Installation Guide, Rev. B 41 LW drives Terminating the drive ST39102LW and ST34502LW drives do not have internal terminators or any other way of adding internal termination to the drive. You must provide external termination to these drives when termination is required. This is normally done by adding an in-line terminator on the cable. Note. Use active (ANSI SCSI-2 Alternative 2) single-ended terminators when terminating a bus operating in singleended mode.
42 Cheetah 9LP Installation Guide, Rev. B LW drives Terminator power You can configure this drive to supply termination power to the SCSI bus by placing a jumper on J2 pins 1 and 2. The default setting is no jumper, meaning that some other source (other than this drive) is suppling termination power to the SCSI bus. Pin 1 Pin 2 J2 RR S D MW P E E T ESEP DSS P Term.
Cheetah 9LP Installation Guide, Rev. B 43 LW drives Other applicable jumper options Several other jumper options are available as illustrated. Pin 1 J2 Pin 2 RR S D MW P E E T E S EP DSS P Reserved Single-Ended Mode option Use single-ended or low voltage differential mode. Force the drive to operate only in single-ended mode. Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) Disable the Delay Motor Start option (default).
44 Cheetah 9LP Installation Guide, Rev.
Cheetah 9LP Installation Guide, Rev. B 45 LW drives Drive Active indicator The drive Active LED indicator connections are shown below. Drive Front Jumper Plug (enlarged to show detail) J6 Pin 1 Reserved Activity LED Reserved The shaded pins are shipped with a cover installed. Do not install jumpers on these pins. Retain the cover unless you install a 20-pin plug. CATH Note: On some LEDs the flat side of indicator is cathode. Figure 15.
46 Cheetah 9LP Installation Guide, Rev. B LC drives Setting the SCSI IDLC jumpers drives section The SCSI ID is normally set over the SCSI bus by the host system. You can also use the J6 jumper block to set the SCSI ID (Figure 16). To change the SCSI ID, install jumpers as shown in the illustration.
Cheetah 9LP Installation Guide, Rev. B 47 LC drives Terminating the drive LC model drives do not have internal terminators or any other way of adding internal termination to the drive. You must provide external termination to these drives when termination is required. Since this drive is designed to be plugged into a backpanel or other host enclosure without cabling, this is normally done by enabling termination on the backpanel or plane. Note.
48 Cheetah 9LP Installation Guide, Rev. B LC drives Other applicable jumper options Other option jumpers are available as illustrated below. Pin 1 J2 Pin 2 RRR S D MW P E E E E S EP DSS S Reserved Single-Ended Mode option Use single-ended or low voltage differential mode. Force the drive to operate only in single-ended mode. Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) Disable the Delay Motor Start option (default).
Cheetah 9LP Installation Guide, Rev. B 49 LC drives Drive Active indicator WC/DC drives section The drive Active LED indicator connections are shown below. Drive Front Jumper Plug (enlarged to show detail) J6 Pin 1 Reserved Activity LED Reserved The shaded pins are shipped with a cover installed. Do not install jumpers on these pins. Retain the cover unless you install a 20-pin plug. CATH Note: On some LEDs the flat side of indicator is cathode. Figure 18.
Seagate Technology, Inc. 920 Disc Drive, Scotts Valley, CA 95066-4544, USA Publication Number: 83329230, Rev.