v6 SATA Product Manual Standard models ST8000DM005 ST6000DM004 ST4000DM006 ST2000DM009 100811076, Rev.
Document Revision History Revision Date Pages affected and Description of changes Rev. A 10/26/2016 Initial release. Rev. B 11/14/2016 fc & 4-6: Changed 4TB model to ST4000DM006 & 2TB model to ST2000DM009 © 2016 Seagate Technology LLC. All rights reserved. Publication number: 100811076, Rev. B November 2016 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Contents Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seagate® Technology Support Services For information regarding online support and services, visit: http://www.seagate.com/contacts/ For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® BarraCuda® Pro v6 Serial ATA model drives:. 512E models ST8000DM005 ST6000DM004 512N model ST4000DM006 ST2000DM009 These drives provide the following key features: • 7200 RPM spindle speed. • Full-track multiple-sector transfer capability without local processor intervention. • High instantaneous (burst) data-transfer rates (up to 600MB per second).
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: 512E models ST8000DM005 2.1 ST6000DM004 512N model ST4000DM006 ST2000DM009 Specification summary tables The specifications listed in the following tables are for quick reference.
Drive specification ST8000DM005 ST6000DM004 ST4000DM006 ST2000DM009 Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz: 0.25 Gs Operation Rotational vibration 20–1500Hz: 12.5 rads/s² 2–500 Hz: 2Hz/.001g2/Hz 4Hz/.03g2/Hz 100Hz/.03g2/Hz 500Hz/.001g2/Hz Vibration, non-operating (Random psd) Drive acoustics, sound power (bels) Idle** 2.8 (typical) 3.0 (max) Performance seek 3.2 (typical) 3.
2.3 Start/stop times 4-8TB models 2TB model Power-on to Ready (sec) (typ/max) 23/30 17 Standby to Ready (sec) (typ/max) 23/30 17 Ready to spindle stop (sec) (max) 23 12 2.4 Recording and interface technology Models 8TB Interface Recording method 6TB 4TB 2TB Serial ATA (SATA) Perpendicular Recording density, KBPI (Kb/in max) 2018 1936 Track density, KTPI (ktracks/in avg) 369 330 Areal density (Gb/in2 avg) 732 651 Spindle speed (RPM) (± 0.
2.5 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 3 on page 24. 2.5.1 Power consumption Power requirements for the drives are listed in Table 3 through Table 5. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. Table 2 DC power requirements (8TB) 6.0Gb mode Voltage +5V Regulation Avg Idle Current * +12V ± 5% Watts Total 0.
Table 3 DC power requirements (6TB) 6.0Gb mode Voltage +5V Regulation Avg Idle Current * +12V ± 5% Watts Total 0.418 0.452 7.52 Idle_A 0.422 0.474 7.80 Idle_B 0.327 0.392 6.33 Idle_C 0.335 0.235 4.49 Standby 0.317 0.007 1.66 DC (peak DC) 0.716 2.0 AC (Peak DC) 0.752 2.92 0.40 0.012 2.14 Typical DC 0.439 0.820 12.03 Maximum DC 0.444 0.825 12.11 Typical DC 0.455 0.725 10.97 Maximum DC 0.460 0.728 11.04 Typical DC 0.439 0.475 7.90 Maximum DC 0.444 0.
Table 4 DC power requirements (4TB) 6.0Gb mode Voltage +5V Regulation Avg Idle Current * +12V ± 5% Watts Total 0.205 0.369 5.45 Idle_A 0.200 0.393 5.70 Idle_B 0.133 0.330 4.63 Idle_C 0.141 0.202 3.13 Standby 0.125 0.001 0.63 DC (peak DC) 0.491 2.0 AC (Peak DC) 0.680 2.680 0.176 0.068 1.70 Typical DC 0.234 0.724 9.86 Maximum DC 0.238 0.734 10.00 Typical DC 0.245 0.692 9.52 Maximum DC 0.248 0.701 9.65 Typical DC 0.505 0.402 7.35 Maximum DC 0.512 0.
Table 5 2TB Drive DC power requirements 6.0Gb mode Voltage +5V Regulation Avg Idle Current * +12V ± 5% Watts Total 0.288 0.267 4.64 Idle_A 0.287 0.265 4.61 Idle_B 0.172 0.236 3.70 Idle_C 0.181 0.145 2.64 Standby 0.162 0.000 0.82 Typical DC 0.311 0.562 8.30 Maximum DC 0.317 0.569 8.41 Typical DC 0.320 0.557 8.29 Maximum DC 0.326 0.567 8.
2.5.1.1 Figure 1. 2.5.2 Typical current profiles Typical 5V and 12V startup and operation current profile Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 V line or an equivalent 15-ohm resistive load on the +5V line. • Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave injected noise at up to 10MHz.
2.5.4 Extended Power Conditions - PowerChoiceTM The Power Choice features are supported on 4TB, 6TB & 8TB models. Utilizing the load/unload architecture a programmable power management interface is provided to tailor systems for reduced power consumption and performance requirements. The table below lists the supported power conditions available in PowerChoice.
PowerChoice Manufacture Default Power Condition Timer Values Default power condition timer values have been established to assure product reliability and data integrity. A minimum timer value threshold of two minutes ensures the appropriate amount of background drive maintenance activities occur. Attempting to set a timer values less than the specified minimum timer value threshold will result in an aborted EPC "Set Power Condition Timer" subcommand.
2.6 Environmental limits Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). To maintain optimal performance drives should be run at nominal drive temperatures and humidity. Note 2.6.1 Temperature a. Operating 41°F to 140°F (5°C to 60°C) drive case temperature range with a maximum temperature gradient of 36°F (20°C) per hour.
2.6.4 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.6.4.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 70 Gs (read) and 40 Gs (write) based on half-sine shock pulses of 2ms. Shocks should not be repeated more than two times per second. 2.6.4.
2.7 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: Note (Number of seeks per second = 0.
2.10 Reliability 2.10.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The production disk drive shall achieve an annualized failure-rate of <1% (MTBF of 1,200,000 hours) over a 5 year service life when used in Enterprise Storage field conditions as limited by the following: • 8760 power-on hours per year.
Capacity; Legal Rights; Indemnity. You represent to SRS that you are of the legal age of majority in your state or country of residence, with the full capacity to agree to these Program Terms. You warrant that you are the legal owner or the authorized representative of the legal owner of the device you submit to SRS (the “Device”) and data.
Dispute Resolution. The parties will attempt to resolve any dispute arising out of or related to these Program Terms or any data recovery services requested or attempted hereunder through good faith negotiation. To the extent permitted by applicable law, if the parties are unable to resolve the dispute through good faith negotiation, then the dispute will be submitted to final and binding arbitration with the Judicial Arbitration and Mediation Services.
Korean RRA If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Agency (RRA) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
2.12.2 China Requirements — China RoHS 2 China RoHS 2 refers to the Ministry of Industry and Information Technology Order No. 32, effective July 1, 2016, titled Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products.
2.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution 3.
3.4.1 Mechanical specifications Refer to Figure 4 for detailed mounting configuration dimensions. See Section 3.4, “Drive mounting.” Weight: Note 8TB & 6TB models 4TB models 2TB models 1.72 lb 1.50 lb 1.21 lb 780 g 680 g 550 g These dimensions conform to the Small Form Factor Standard documented in SFF-8301 and SFF-8323, found at www.sffcommittee.org 4X 6-32 UNC 2B 3 MIN THREAD DEPTH .12 MAX FASTENER PENETRATION MOUNTING HOLE. MAX TORQUE 6 IN/LBS 2X 3.000±.010 2X 4.000±.010 2X 1.625±.020 1.
4X 6-32 UNC 2B 3 MIN THREAD DEPTH .1 MAX FASTENER PENETRATION MOUNTING HOLES BOTH SIDES. MAX TORQUE 6 IN/LBS 2X 4.000±.010 5.787 MAX 146.99 MM 2X 1.750±.010 2X 1.638±.010 2X 1.625±.010 CL OF CONN 1.432±.019 2 2X 1.122±.010 .814±.020 2 .128±.010 CL OF DRIVE Y .250±.010 Z 3.750±.010 4.000±.010 CL OF DRIVE 2.000 TEMPERATURE CHECKPOINT 60°C MAX Figure 5. Note .138±.015 2 Y 6X 6-32 UNC 2B 3 MIN THREAD DEPTH .1 MAX FASTENER PENETRATION MOUNTING HOLES BOTH SIDES. MAX TORQUE 6 IN/LBS Z 1.
Figure 6. Note Mounting configuration dimensions (2TB) The image is for mechanical dimension reference only and may not represent the actual drive. Seagate BarraCuda Pro v6 Serial ATA Product Manual, Rev.
4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/ output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. 4.
4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. commands” on page 35.for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Seek 70H Set Date & Time Ext 77H Set Features EFH Set Multiple Mode C6H Sleep E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T. Enable/Disable Autosave B0H / D2H S.M.A.R.T. Enable Operations B0H / D8H S.M.A.R.T. Execute Offline B0H / D4H S.M.A.R.T. Read Attribute Thresholds B0H / D1H S.M.A.R.T. Read Data B0H / D0H S.M.A.R.T. Read Log Sector B0H / D5H S.M.A.R.T. Return Status B0H / DAH S.M.A.R.T. Save Attribute Values B0H / D3H S.M.A.R.T.
4.3.1 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 10 on page 29. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 5 for default parameter settings.
Word Description Value 64 Advanced PIO modes supported (modes 3 and 4 supported) 0003H 65 Minimum multiword DMA transfer cycle time per word (120 ns) 0078H 66 Recommended multiword DMA transfer cycle time per word (120 ns) 0078H 67 Minimum PIO cycle time without IORDY flow control (240 ns) 0078H 68 Minimum PIO cycle time with IORDY flow control (120 ns) 0078H 69 Additional supported 00008H 70–74 ATA-reserved 0000H 75 Queue depth 001FH 76 Serial ATA capabilities 8D0EH 77 Reserv
Word Description Value 206 SCT Command Transport command set. If bit 0 is set to one, then the device supports SCT Command Transport. Bits 7:2 indicate individual SCT feature support. xxBDH 207-254 ATA-reserved 0000H 255 Integrity word xxA5H Note See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported.
4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100811076, Rev.
