Code : SEA 207K ASSEMBLY MANUAL Specifications: Wingspan--------------- 63.0 in (160.0 cm). Wing area--------------- 728.5 sq.ins (47.0 sq.dm). Weight------------------- 9.3-9.9 lbs (4.2-4.5 kg). Length------------------- 51.8 in (131.5 cm). Engine ------------------ 0.61 - 0.91 cu.in----2 stroke. ---------------------------- 0.91- 1.00 cu.in----4 stroke. ---------------------------- 15cc gasoline engine . Radio--------------------- 6 channels with 9 servos.
Instruction Manual. P-47D Thunderbolt 60 Kit INTRODUCTION - Congratulations and thank you for purchasing the P47 Thunderbolt. We are pleased to bring you this scale P47. with this kit you can achieve whatever level of detail you like. Just by following the instruction and finishing the plane in scale-looking trim scheme, beginning scale modelers will end up with a model that very much represents and full-size P47.
P-47D Thunderbolt 60 Kit 4 Instruction Manual.
P-47D Thunderbolt 60 Kit 6 Instruction Manual.
P-47D Thunderbolt 60 Kit 8 Instruction Manual.
BUILD THE FUSELAGE 4. 1. - Fill White Glue on the surface of the 1st firewall F0. 5. - Firewall ( 3pcs). 2. - Put the 2nd firewall F0 on 1st firewall F0 to paste them together. 6. 3. - Apply White Glue to the surface of the firewall F0’. - Apply Epoxy around block include 3 layers firewall. 7. - Put the 1st firewall F0 on firewall F0’ to paste them together.
Instruction Manual. P-47D Thunderbolt 60 Kit - Arrange the left fuselage side S1, S1’ and the right fuselage side S2, S2’ as photo for difference between inside surface and outside surface. Please kindly see in the drawing sheet so that avoiding mistake at this step. - Apply White Glue to the surface of left fuselage side S1 at area need to paste S1’. 11. 8. - Put the left fuselage side S1’ on the left fuselage side S1 to paste them together.
17. 14. - Apply CA Glue to keep fixed former F1 and the right fuselage side S2, S2’. - Install firewall block with the right fuselage side S2,S2’ by Epoxy glue. Continue to install former F13 as the instruction photos below. 15. 18. - Put former F1 on the right fuselage side S2,S2’. 19. 16. 20. - Use the ruler to adjust perpendicular angle of former F1 and the right fuselage side S2, S2’.
Instruction Manual. P-47D Thunderbolt 60 Kit 21 . 25. 22. 26. 23. 27. 24. 28.
29. 33. 30. 34. 31. 35. 32. 36.
Instruction Manual. P-47D Thunderbolt 60 Kit 37. 41. 38. 42. 39. 43. 40. 44.
45. 49. 46. 50. 47. 51. 48. 52.
Instruction Manual. P-47D Thunderbolt 60 Kit 57. 53. 58. 54. 59. 55. - Use White Glue to paste former F14’ ( 2pcs) on former F14. 60. 56. - Apply CA Glue around block include 3 layers former F14, F14’.
64. 61. - Apply CA Glue to keep fixed block former F14, F14’ with two side of fuselage. - Attach M3 blind nut ( 4pcs) to block of former F14, F14’. 62. 65. - Continue to install for the end former. - Apply CA Glue around M3 blind nut ( 4pcs). 66. 63. - Install block of former F14, F14’ to the fuselage side. - Use Aluminium Square Fixed Tool to go through all formers at the square hole on each former.
Instruction Manual. P-47D Thunderbolt 60 Kit 67. 70. - Install F26 and apply CA Glue to keep fixed. - Install F16 and apply CA Glue to keep fixed. 71. 68. - Install F27 and apply CA Glue to keep fixed. 72. - Install F2’ to F2 by White Glue. 69. 73. - Apply thin CA Glue around block include 2 layers former F2,F2’.
- Install F17 ( 3pcs) to fuselage and apply CA Glue 77. to keep fixed. 74. - Paste F19’ on F19 by CA Glue. 78. - Install F18 ( 2pcs) to fuselage and apply CA Glue to keep fixed. 75. - Attach M4 blind nut to block of former F19, F19’ and apply CA Glue around M4 blind nut. 79. - Install SW1 at right side and SW2 at left side, then apply CA Glue to keep fixed. 76. - Install block of former F19, F19’ to fuselage and apply CA Glue to keep fixed.
Instruction Manual. P-47D Thunderbolt 60 Kit 80. 83. 84. 81. - Install H17 to fuselage and apply CA Glue to keep fixed. 82. - Install F20 ( 2pcs) to fuselage and apply CA Glue to keep fixed. 85. 86. - Install F32 to fuselage and apply CA Glue to keep fixed.
- Install F23 ( 2pcs) to fuselage and apply CA Glue 90. to keep fixed. 87. - Use sandpaper bar to sanding F21, so that making a flat with fuselage side. 88. 91. - Install F21 ( 2pcs) to fuselage and apply CA Glue 92. to keep fixed. 89. - Install FW’ to fuselage at right side and left side, then apply CA Glue to keep fixed. - Use cutter knife cut off redundantcy wood of F21.
Instruction Manual. P-47D Thunderbolt 60 Kit 93. - Install F21’ ( 2pcs) to fuselage at right side and left side and apply CA Glue to keep fixed. 97. 94. - Install F25 to fuselage at right side and left side, then apply CA Glue to keep fixed. 98. - Install F25’ to fuselage at right side and left side, then fill CA Glue to keep fixed. 95. 99. 96. - Install F24 to fuselage at right side and left side, then apply CA Glue to keep fixed.
100. - Getting prepare the plastic tube ( 4pcs) with Ø = 5mm ; 36cm length (photo 103). 104. 101. - The plastic tube to go through all formers which have path of Fin and path of Elevator hole on each former and fill White Glue to keep fixed. Please kindly see in the drawing sheet so that avoiding mistake at this step. 105. - Install H10 to fuselage at right side and left side, then apply CA Glue to keep fixed. 102. 106. 103.
Instruction Manual. P-47D Thunderbolt 60 Kit COVER TO THE RIBS OF FUSELAGE 4. If the balsa sheet quite hard, we should use the wet towel so that making soft the balsa sheet. 1. - Use cutter knife cut off redundantcy of SH3. 5. 2. - Cover the sheet SH4 on ribs of fuselage at the right side. 6. - Cover the sheet SH3 on ribs of fuselage at the left side. 3. - Cover the sheet SH1 on ribs of fuselage at the right side. - Use the pen make mark at the center.
7. 10. - Cover the sheet SH2 on ribs of fuselage at the left side. 8. - Cover the sheet SH14 on ribs of fuselage at the right side. 11. 12. 9. 13. - Cover the sheet SH13 on ribs of fuselage at the left side.
Instruction Manual. P-47D Thunderbolt 60 Kit - Cover the sheet SH11 on ribs of fuselage at the 17. both of side. 14. - Cover the sheet SH12 on ribs of fuselage at the both of side. - Cover the sheet SH7 on ribs of fuselage at the 18. both of side. 15. - Apply CA Glue to keep fixed the sheet SH12. 19. - Use cutter knife cut SH7 at position of the formers so that bending the sheet easily. 16. 20. - Apply CA Glue at position of the crack on the sheet SH7.
- Cover the sheet SH6 on ribs of fuselage at the 24. both of side apply CA Glue to keep fixed. 21. 25. - Cover the sheet SH5 on ribs of fuselage at the both of side. 22. - Cover the sheet SH8 on ribs of fuselage at the both of side and apply CA Glue to keep fixed the sheet SH8. 26. - Use the pen make mark at the center and then use Cutter knife to cut off redundantcy of SH5. 23. 27. - Apply CA Glue to keep fixed the sheet SH5.
Instruction Manual. P-47D Thunderbolt 60 Kit - Install F30 and F31 (8mm balsa wood ) to fuselage and apply CA Glue to keep fixed. 28. Should use the wing as instruction photo so that installing FW exactly as photo. 31. - Use cutter knife to cut off redundantcy wood of F31. 29. - Apply CA Glue to keep fixed FW. 32. - Apply white Glue to the surface of the 1st F22 (8mm) and paste on the 2nd F22 (8mm). - Use sandpaper bar to sanding block include F30 and F31, making flat with fuselage side. 33. 30.
37. 34. - Roll sandpaper around the paper tube so that making a sandpaper tube. - Install 16mm block F22 to the fuselage by White Glue. 38. 35. - Sanding wood block F22 so that shaping the wing fillet. - Apply CA Glue to keep fixed 16mm block F22 sticky more. 36. 39. - Use cutter knife to cut off redundantcy wood of 16mm block F22 as photo. - Use countersink with Ø = 4mm, to drill the hole for antenna at the top of fuselage as photo.
Instruction Manual. P-47D Thunderbolt 60 Kit 43. 40. - Use countersink with Ø = 3mm, to drill the hole 44. for bomb at the bottom of fuselage as photo. 41. - Install F22 to fuselage and apply CA Glue to keep fixed. - The fuselage was finished. 45. 42. - Remove aluminium square fixed tool. 30 - Use sandpaper bar to sanding at the end of fuselage ( F15).
46. 49. - Paste F15’ on the end of fuselage at F15 by CA Glue. 47. - Use sandpaper bar to sanding at block of tab as photo. 50. - Getting prepare set of cowling mount include set 51. of tap ( 4set) and F1’. 48. - Install F1’ to fuselage and fill CA Glue to keep fixed. - Paste the tap together as photo and then install to F1’ by CA Glue.
Instruction Manual. P-47D Thunderbolt 60 Kit 52. 55. - Apply white Glue to keep fixed paper tube. - Apply white Glue to the surface of the triangle block as photo. INSTALLING THE FUSELAGE SERVOS 53. Because the size of servos differ, you may need to adjust the size of the precut opening in the mount. The notch in the sides of the mount allow the servo lead to pass through. - Install the rubber grommets and brass collets into all servos. Test fit the servos into the fuselage servo mounts.
THROTTLE SERVO ARM INSTALLATION 2. - Install adjustable servo connector in the servo arm as same as picture below: 1. Vent tube. Fuel pick up tube. Fuel fill tube. - Carefully bend the second nylon tube up at a 45º angle. This tube is the vent tube. - Test fit the stopper assembly into the tank. It may be necessary to remove some of the flashing around the tank opening using a modeling knife. If flashing is present, make sure none falls into the tank.
Instruction Manual. P-47D Thunderbolt 60 Kit - Slide the fuel tank into the fuselage. Guide the lines from the tank through the hole in the fiewall. 1. - Use plywood template to hold in place the fuel tank with C/A glue to secure the fuel tank inside the fuselage. 2. 145mm Balsa wood - Use a pin drill and 4mm drill bit to drill a small indentation in the mount for the engine mounting screw. Epoxy 2. 3.
- Move the throttle stick to the closed position and move the carburetor to closed. Use a 2.5mm hex wrench to tighten the screw that secures the throttle pushrod wire. Make sure to use threadlock on the screw so it does not vibrate loose. - On the fie wall has the location for the throttle pusshrod tube (pre-drill). - Slide the pushrod tube in the fiewall and guide it through the fuel tank mount. Use medium C/A to glue the tube to the fiewall and the fuel tank mount.
Instruction Manual. P-47D Thunderbolt 60 Kit 6. 3. - Slide the fberglass cowl over the engine and line up the back edge of the cowl with the marks you made on the fuselage then trim and cut as shown. 4. - Because of the size of the cowl, it may be nec essary to use a needle valve extension for the high speed needle valve. Make this out of suf fcient length 1.5mm wire and install it into the end of the needle valve. Secure the wire in place by tightening the set screw in the side of the needle valve.
- Install the mufer and mufer extension onto the - Paste prepare aluminium square tool on canopy engine and make the cutout in the cowl for mufer at the bottom by sticky tape. clearance. Connect the fuel and pressure lines to 4. the carburetor, mufer and fuel fller valve. Secure the cowl to fuse lage using the M3x10mm screws. BUILD THE CANOPY 1. - Cover balsa sheet SH10 on the rib of canopy at the both side. 5. - Install the ribs for canopy include H1, H2, H3, H4, H5, H6, H7, H8, H9 by CA glue. 2.
Instruction Manual. P-47D Thunderbolt 60 Kit 7. - Attach M4 blind nut to the latch and then fill CA glue around. 11. - Getting prepare 2 set of latch at behind include H10’ ( 4pcs). 8. - Attach the latch to canopy at behind by CA glue. 12. - Paste 2 pieces together make for each the latch by CA glue. 9. 13. 10. - Attach the latch to canopy at before by CA glue.
14. 2. - Cover the rest of the clear area with making tape so that mask off protect it from over spray (photo 15.16). - Install canopy to fuselage and use the sandpaper bar so that sanding for canopy and fuselage until look seamless. 3. 15. - Use sandpaper to sanding all around the fuselage. - Paint the canopy frame. 4. PAINT THE CANOPY FRAME 1. - Remove the paper.
Instruction Manual. P-47D Thunderbolt 60 Kit - Position the canopy onto the fuselage. Trace around the canopy and onto the fuselage using a felt-tipped pen. INSTALLATION PILOT AND CANOPY - Locate items necessary to install pilot, seats. 3. 1. - A scale pilot is included with this ARF. The Pilot included fiting well to the coc pit. (or you can order others scale pilot fiures made by SG Models. They are available at SG Models distributors.) 1.
- Getting prepare the perpendicular frame include 6. 2 pcs paste on together. 3. - Paste W28 on W29 by White Glue. - The Aluminium Square Fixed Tool be separated 2 parts. 7. 4. - Apply thin CA Glue around block include 2 layers of trailing edge. 8. - Weld 2 parts the Aluminium Square Fixed Tool as perpendicular aluminium frame. 5. - Buid the ribs for wing. - Getting prepare trailing edge include W28 and W29.
Instruction Manual. P-47D Thunderbolt 60 Kit 9. 12. - Apply CA Glue to keep fixed the airfoil. - Use the clamp to hold on perpendicular aluminium frame and the ribs of wing together. 10. 13. - Install leading edge to the ribs of wing. - Use cutter knife to cut trailing edge at mark but cutting do not cut off. 11. 14. - Apply CA Glue to keep fixed leading edge. 42 - Bend to create for the trailing edge as photo.
Please kindly see the view of wing in the 18. drawing sheet. 15. 19. 16. 20. - Install F15 to wing and apply CA Glue to keep fixed as photo. 17. - Install W13 and W32 to wing and apply CA Glue to keep fixed as photo. 21. - Use sandpaper bar to sanding at the end airfoil of wing as photo.
Instruction Manual. P-47D Thunderbolt 60 Kit 22. 25. - Install W15’(6mm balsa wood) to wing and apply 26. CA Glue to keep fixed as photo. 23. - Install W5 to wing by White Glue to keep fixed as photo. 27 . 24. - Install W6 to wing by White Glue to keep fixed as photo. 44 - Paste two pieces retract gear mount W21 together by White Glue.
32. 28. - Apply thin CA Glue to around block include 2 layers W21. 29. - Install retract gear mount W21 to wing by White Glue and then fill CA Glue to keep fixed. 33. - Paste W22 on W21 by White Glue as photo. 30. 34. 31. 35.
Instruction Manual. P-47D Thunderbolt 60 Kit - Paste W23 on block include W21, W22 by White Glue and then fill CA Glue to mount to keep fixed. - Getting prepare set of nut for nylon bolt include W34 (2pcs) and a nylon nut as photo. 40. 36. 37. - Paste two pieces W34 and a nylon nut together by CA glue. 41. 38. 42. - Install W19 and W20 to wing by White Glue and then apply CA glue to keep fixed as photo. 39. - Install block of nut to wing root by by CA glue as photo.
43. - Apply CA glue to keep fixed W18. 47. 44. - Install servo mount WS3, WS4, WS5 to wing by CA glue. 48. - Getting prepare W18 and M3 blind nut and attaching M3 blind nut to W18 by White glue. 45. - Apply White glue on trailing edge as photo. 49. - Install W18 with blind nut available to W2 by White glue. 46. - Cover the balsa sheet W41, attach the balsa sheet to tabs of trailing edge.
Instruction Manual. P-47D Thunderbolt 60 Kit 53. 50. - The side of wing with servo mount flip up as photo. 51. - Sheeting was finished. 54. -Use sandpaper bar to sanding 6mm balsa block make shape for balsa block as photo. - Apply balsa frame W25 to balsa sheet W39 at mark area for wheel’s well. 55. 52. - Cover the balsa sheet W39 with balsa frame W25 available to wing . 48 - Attach 6mm balsa block to leading edge at mount of gun as photo.
56. 60. - Cover balsa sheet W38 for 2nd side of wing by White glue as photo. 57. 61. - Measure and split to two fragment of 6mm balsa block for leading edge. - Hold the sheet down with weights while the glue dries. 58. 62. - Attach two fragment of 6mm balsa block to leading edge by CA glue. 59. 63.
Instruction Manual. P-47D Thunderbolt 60 Kit - Install W33 by CA glue. 64. 68. 65. 69. 66. - Paste W16 on W4 by White Glue. 70. - Cover balsa sheet W35 and W36 at servo area (photo 62 to 66). 71. 67.
- The paper tube through W1, W2, W3, W4 and 75. then apply White glue at intersection of the wing rib and the tube as photo. 72. - Apply CA glue to keep fixed W40. 76. - Cut off the paper tube at wing root as photo. 73. - Use sandpaper bar to sanding at 6mm balsa block W15’ as photo. 77. 74. - Sanding was finished. - Cover balsa sheet W40 by white glue.
Instruction Manual. P-47D Thunderbolt 60 Kit 78. - The aluminium tube through the ribs and then fill CA glue to keep fixed. 82. - Use sandpaper bar to sanding at trailing edge . 79. - Paste W1 on W1’ by CA glue to keep fixed. 83. 80. - Attach the pin ( 2pcs) Ø = 8mm to wing root as photo. 84. - Paste W1’ on W2 by white glue. 81. - Use sandpaper bar to sanding at leading edge.
85. BUILD THE FLAP AND AILERON 1. - Sanding leading edge was finished. 86. - Getting prepare set of flap as photo. 2. - Use sandpaper to sanding around wing. 87. - Install the ribs of flap to balsa sheet WA15 and leading edge of flap WA14 by CA glue. 3. - Building the wing was finished. - Paste balsa block WA19 on leading edge of flap by white glue .
Instruction Manual. P-47D Thunderbolt 60 Kit - Apply CA glue to keep fixed as photo. 4. 8. - Apply CA glue at leading edge WA19 with balsa sheet WA15 to keep fixed as photo. 5. - Use sandpaper bar to sanding at root rib of flap. 9. - Apply white glue to the ribs of flap as photo. 6. 10. - Cover balsa sheet WA16 to the ribs of flap. 7. - Make mark angle 45 degree, toward side of control hole as photo (photo 9,10).
11. - Install the ribs of aileron to balsa sheet WA17 and leading edge of aileron WA13 by CA glue. 15. - Use sandpaper bar to sanding make the angle of flap. 12. - Apply white glue to the ribs of aileron as photo. 16. - The flap was finished. 13. - Cover balsa sheet WA18 to the sibs of aileron 17. - Getting prepare set of aileron as photo. 14. - Apply CA glue to keep fixed as photo.
Instruction Manual. P-47D Thunderbolt 60 Kit 18. 21. - Use the pen make the mark of hinge on flap follow wing. - Paste balsa block WA20 on leading edge of aileron by white glue. 19. 22. - Use the pen make the mark of hinge on aileron follow wing. - Apply CA glue at leading edge WA20 with balsa sheet WA17 to keep fixed as photo. 20. 23. - Use sandpaper bar for sanding leading edge WA20. 56 - Building the set of wing was finished.
- Deflect the flap and completely saturate each hinge with thin C/A glue. The ailerons front surface should lightly contact the wing during this procedure. Ideally, when the hinges are glued in place, a 1/64” gap or less will be maintained throughout the lengh of the flap to the wing panel hinge line. HINGING THE FLAP Note : The control surfaces, including the ailerons, elevators, and rudder, are prehinged with hinges installed, but the hinges are not glued in place.
Instruction Manual. P-47D Thunderbolt 60 Kit 4. 2. Note : Work the aileron up and down several times to “work in” the hinges and check for proper movement. - Slide the wing panel on the aileron until there is only a slight gap. The hinge is now centered on the wing panel and aileron. Remove the T-pins and snug the aileron against the wing panel. A gap of 1/64” or less should be maintained between the wing panel and aileron.
- Using C/A remover/debonder and a paper towel, 2. remove any excess C/A glue that may have accumulated on the wing or in the aileron hinge area. - Repeat this process with the other wing panel, securely hinging the aileron in place. - After both ailerons are securely hinged, firmly grasp the wing panel and aileron to make sure the hinges are securely glued and cannot be pulled out. Do this by carefully applying medium pressure, trying to separate the aileron from the wing panel.
Instruction Manual. P-47D Thunderbolt 60 Kit INSTALLING THE AILERON SERVOS 3. 1. - Use drill bit in a pin vise to drill the mouting holes in the blocks. 4. 2. Minimum servo spec. Torque : 80 oz-in (5.8 kg-cm) @ 4.8V; 100 ozin (7.2 kg-cm) @ 6.0V Because the size of servos differ, you may 5. need to adjust the size of the precut opening in the mount. The notch in the sides of the mount allow the servo lead to pass through.
INSTALLING THE LIGHT COVER - Please see below pictures. AILERON PUSHROD INSTALLATION 1. 1. 2. 2. INSTALLING THE FLAP PUSHROD - Repeat the procedure for the aileron pushrod. 3. 1. 2.
Instruction Manual. P-47D Thunderbolt 60 Kit INSTALLING RETRACTABLE LANDING GEAR 4. - Locate the items necessary to install the retractable landing gear as shown. 1. RETRACTABLE LANDING GEAR SERVO - PUSHROD INSTALLATION - Locate items necessary to install landing gear pushrod. - Install retractable landing gear at the Wing. 1. 2. 2. 3.
3. 7. 8. 4. 9. 5. 10. 6.
Instruction Manual. P-47D Thunderbolt 60 Kit 1. 5. - Install the ribs of stabilizer as photo. - Hold the sheet down with weights while the glue dries and apply CA/glue to the sheet at trailing edge. 2. 6. - Cover balsa sheet ST14 for 1st side by white glue and then apply CA glue to keep fixed. 7. 3. - Install the 6mm balsa block ST12 by white glue as photo and then apply CA glue to keep fixed (photo 6,7) 4. 8.
- Use cutter to sharpen the ST12 for flatting surface of stabilizer. 9. - Install the ribs of elevator to balsa sheet ST15 and leading edge of elevator ST13 by white glue. 2. - Apply white glue to the ribs of elevator and cover the balsa sheet ST15’ as photo. - Use sandpaper bar for sanding the surface of stabilizer. 10. 3. - Building the stabilizer was finished. 4. BUILD THE ELEVATOR 1. - Apply white glue to leading edge so that attaching triangle balsa block and 6mm balsa block ST16.
Instruction Manual. P-47D Thunderbolt 60 Kit 8. 5. - Use the pen make the mark of hinge on elevator follow stabilizer. - Use cutter knife to sharpen the ST16 for flatting surface of elevator. 9. 6. - Set of Stab and elevator was buildded . - Use sandpaper bar for sanding leading edge and ST16. 7. 10. - Building elevator was finished. 66 - Use sandpaper to sanding around set of stab and elevator.
- Using a ruler and a pen, locate the centerline of the horizontal stabilizer, at the trailing edge, and place a mark. Use a triangle and extend this mark, from back to front, across the top of the stabilizer. Also extend this mark down the back of the trailing edge of the stabilizer. HINGING THE ELEVATORS - Glue the elevator hinges in place using the same techniques used to hinge the ailerons. 1. 1.
Instruction Manual. P-47D Thunderbolt 60 Kit - With the stabilizer held firmly in place, use a pen and draw lines onto the stabilizer where it and the fuselage sides meet. Do this on both the right and left sides and top and bottom of the stabilizer. - When you are sure that everything is aligned correctly, mix up a generous amount of 30 Minute Epoxy. Apply a thin layer to the top and bottom of the stabilizer mounting area and to the stabilizer mounting platform sides in the fuselage.
2. 5. - Apply white glue to the ribs of rudder. 3. - Cover balsa sheet T17 at botton of rudder as photo. 6. - Cover 2nd balsa sheet T19 to the ribs of rudder. 4. - Cover balsa sheet T18 for two side as photo. 7. - Apply CA glue at the tabs show on the sheet to keep fixed.
Instruction Manual. P-47D Thunderbolt 60 Kit 11. 8. - Use sandpaper bar for sanding the surface of rudder. - Attach 8mm balsa block for two side by CA glue as photo. 9. 12. - Attach 8mm balsa block T5’ by CA glue as photo. - Building the rudder was finished. 10. BUILD THE FIN 1. - Use a cutter to sharpen the T5’ for flatting surface of rudder.
5. 2. 3. - Cover balsa sheet T20 on the ribs of fin. 6. - Install the ribs of fin to balsa sheet T22 and leading edge of fin T15 and then attach 6mm balsa block T13 by CA glue as photo. 4. - Apply CA glue at the tabs show on the sheet to keep fixed. 7. - Apply white glue to the ribs of fin. - Use sandpaper bar for sanding at T13 for making the shape round as the sheet.
Instruction Manual. P-47D Thunderbolt 60 Kit 8. 11. 9. - Paste 2 pieces 8mm balsa block T21 together by CA glue. 12. - Apply white glue to leading edge so that triangle balsa block. 10. 13. - Apply CA glue to keep fixed triangle balsa block. 72 - Attach to leading edge of fin by CA glue as photo.
14. 17. - Use the pen make the mark of hinge on the fin follow rudder. - Use cutter knife to sharpen the T21 for flatting surface of fin. 18. 15. - Use the cutter knife cut off a slot for hinge. - Use sandpaper bar for sanding around the fin. 16. 19. - Building the fin was finished. - Set of rudder and fin was finished.
Instruction Manual. P-47D Thunderbolt 60 Kit 20 3. - Use sandpaper to sanding around set of rudder and fin. SET UP THE KIT - Put the stabilizer and continue to sanding until fitting, there no slit at here. At the same time, the stabilizer and the wing tube have to parallel together. 4. 1. 5. - Use sandpaper tube for sanding the area where install stabilizer. 2.
2. 6. - Set up the kit was finished. INSTALLING VERTICAL STABILIZER HINGING THE RUDDER - Glue the rudder hinges in place using the same techniques used to hinge the ailerons. 1. 1. - Using a modeling knife, remove the covering from over the precut hinge slot cut into the lower rear portion of the fuselage. INSTALL RUDDER CONTROL HORN 2. - Repeat steps to install the rudder control horn as same as steps done for ailerons. 1.
Instruction Manual. P-47D Thunderbolt 60 Kit - While holding the vertical stabilizer fimly in 6. place, use a pen and draw a line on eachside of the vertical stabilizer where it meets the top of the fuselage. 3. - When you are sure that everything is aligned correctly, mix up a generous amount of Flash 30 Minute Epoxy. Apply a thin layer to the mounting slot and to bottom of the vertical stabilizer mounting area. Apply epoxy to the bottom and top edges of the filler block and to the lower hinge also.
2. 6. - Thead one clevis and M2 lock nut on to each elevator control rod. Thead the horns on until they are flsh with the ends of the control rods. - Elevator and rudder pushrods assembly as pictures below. RUDDER PUSHROD INSTALLATION - Locate items necessaryto install rudder pushrod. 1. 3. 2. 4. 5. 3.
Instruction Manual. P-47D Thunderbolt 60 Kit 4. 3. MOUNTING THE TAIL WHEEL 4. - Locate items necessary to intall tail wheel. 1. 5. 2.
6. 10. 11. 7. 12. 8. - Insert fuel tank onto the wings. 13. 9.
Instruction Manual. P-47D Thunderbolt 60 Kit 14. 1. - Getting prepare set of servo mount include WS1, WS2 (2 pcs), WS6 (2 pcs) as photo. 15. 2. 3. 16. BUILD THE SERVO MOUNT 80 - The first, build servo mount by CA glue and then apply white glue to keep fixed.
BUILD THE MOTOR MOUNT 4. 1. - Paste 3 pieces MO1 together by white glue and then apply CA glue around block include 3 layer to keep fixed. - Getting prepare set of motor mount include MO1 5. ( 3pcs), MO2 ( 1pcs), MO3 ( 2pcs), MO4 ( 2pcs), MO5 (1pcs). 2. 6. 3. - Paste 2 pieces MO3 together by white glue.
Instruction Manual. P-47D Thunderbolt 60 Kit 7. 10. - Paste MO3 block on MO2 by white glue and apply CA glue around block include 3 layer to keep 11. fixed. And then attach to MO4 by CA glue. - Attach MO1 block to MO4 by CA glue(photo 9,10). 8. - Continue to attach the 2nd M04 by CA gluce. 12. - Use perpendicular ruler for making angle 90 degree. 9. 13.
- Locate the items neccessary to install the electric power conversion included with your model. - Continue to attache M05 at the botton of motor mount by CA glue (photo 12,13). 14. 1. - Getting prepase two triange block lenght = 65mm. 15. - Recommend the items necessary to install the electric power conversion parts included with your model. - Model size: .75-.
Instruction Manual. P-47D Thunderbolt 60 Kit - Attach the motor to the front of the electric motor box using four 4mm blind nut, four M3x15mm hex head bolts to secure the motor. Please see picture shown. 3. 6. - Attach the motor mount to the front of the electric motor box using four 4mm blind nut, four M3x15mm hex head bolts to secure the motor. Please see picture shown. 7. 4. - Attach the speed control to the side of the motor box using two-sided tape and tie wraps.
- Lif the model. If the tail drops when you lift the model is “tail heavy” and you must add weight* to the nose. If the nose drops, it is “nose heavy” and you must add weight* to the tail to balance. BALANCING - It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash.THE CENTER OF GRAVITY IS LOCATED 100 MM BACK FROM THE LEADING EDGE OF THE WING AT THE WING ROOT. - Mount the wing to the fuselage.
P-47D Thunderbolt 60 Kit 86 Instruction Manual.
If you have any queries, or are interested in our products, please feel free to contact us Factory : 12/101A - Hamlet 4 - Le Van Khuong Street - Dong Thanh Ward Hoc Mon District - Ho Chi Minh City - Viet Nam. Office : 62/8 Ngo Tat To Street - Ward 19 - Binh Thanh District - Ho Chi Minh City - Viet Nam Phone : 848 - 86622289 or 848- 36018777 Website : www.SeagullModels.com Email : Sales@seagullmodels.com Facebook : www.facebook.com/SeaGullModels.
