Code : SEA 285 ASSEMBLY MANUAL Speciications: Wingspan--------------- 80.0 in (203.2 cm). Wing area--------------- 957.9 sq.ins (61.8 sq.dm). Weight------------------- 13.7-14.1 lbs (6.2-6.4 kg). Length------------------- 58.8 in (147.2 cm). Engine/Motor size----- 0.46-0.55 cu.in 2stroke. Radio--------------------- 8 channels with 10 servos.
Instruction Manual. Seagull de Havilland Mosquito Twin Engine RC Warbird INTRODUCTION. hank you for choosing the Seagull de Havilland Mosquito Twin Engine RC Warbird ARTF by SG MODELS . he Seagull de Havilland Mosquito Twin Engine RC Warbird was designed with the intermediate/advanced sport lyer in mind. It is a semi scale airplane which is easy to ly and quick to assemble.
KIT CONTENTS. SEA285 Seagull de Havilland Mosquito Twin Engine RC Warbird 1. Fuselage 2. Wing set (2) 3. Tail set (2) 4. Canopy 5. Cowling (2) 6. landing gear 7. Pilot 8. wheel (2) 9. Aluminum wing tube 10. EP Conversion pack INSTALL THE AILERONS CONTROL HORN. Fiberglass control horn ADDITIONAL ITEMS REQUIRED. � 0.46-0.55 cu.in 2stroke. � Computer radio 8 with chanlel 10 servos. � Glow plug to suit engine. � Propeller to suit engine. � Protective foam rubber for radio system. Epoxy.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. Epoxy. Fiberglass control horn INSTALLING THE ALLERON SERVOS.
C/A glue Because the size of servos difer, you may need to adjust the size of the precut opening in the mount. he notch in the sides of the mount allow the servo lead to pass through. 1) Place the servo between the mounting blocks and space it from the hatch. Use a pencil to mark the mounting hole locations on the blocks. 2) Use drill bit in a pin vise to drill the mouting holes in the blocks. 4) Use dental loss to secure the connection so they cannot become unplugged.
Instruction Manual. Seagull de Havilland Mosquito Twin Engine RC Warbird 7) Remove the string from the wing at the servo location and use the tape to attach it to the servo extension lead. Pull the lead through the wing and remove the string. 8) Set the aileron hatch in place and use a Phillips screw driver to install it with four wood screws. 2x10mm AILERON PUSHROD INSTALLATION. Please see below pictures.
INSTALLING THE FLAP SERVO. Repeat the procedure for the lap servo. Metal R/C Clevis Pushrod Wire INSTALLING THE FUSELAGE SERVOS. Hex Nut Fuel Tubin g Because the size of servos difer, you may need to adjust the size of the precut . opening in the mount. he notch in the sides of the mount allow the servo lead to pass through. 1) Install the rubber grommets and brass collets into all servos. Test it the servos into the fuselage servo mounts.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. ENGINE MOUNT INSTALLATION Rudder servo arm. 1) Locate the items necessary to install the engine mount included with your model Elevator servo arm. INSTALLING THE RECEIVER SWITCH. Install the switch into the precut hole in the side, in the fuselage. 3/32” Hole. Trim and cut. . Switch. 8 2) Use four 4x20mm head bolts and four 4mm washers to attach the engine mount rails to the irewall. Tighten the screws .
1) Position the engine with the drive washe (118mm) forward of the irewall as shown. Knife. 118mm. 2) Use a pin drill and 2mm drill bit to drill a small indentation in the mount for the engine mounting screw. 2mm. Epoxy. 3) Use a drill to drill the four holes in the engine mount rails 4mm.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. Vent tube. Fuel pick up tube. INSTALLING THE STOPPER ASSEMBLY. 1) Using a modeling knife, carefully cut of the rear portion of one of the 3 nylon tubes leaving 1/2” protruding from the rear of the stopper. his will be the fuel pick up tube. 2) Using a modeling knife, cut one length of silicon fuel line. Connect one end of the line to the weighted fuel pick up and the other end to the nylon pick up tube. 10 Fuel fill tube.
5) With the stopper assembly in place, the weighted pick-up should rest away from the rear of the tank and move freely inside the tank. he top of the vent tube should rest just below the top of the tank. It should not touch the top of the tank. 6) When satisied with the alignment of the stopper assembly tighten the 3 x 20mm machine screw until the rubber stopper expands and seals the tank opening. Do not overtighten the assembly as this could cause the tank to split. FUEL TANK INSTALLATION.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. 1) Connect the Z-bend in the 450mm throttle pushrod to the outer hole of the carburetor arm. 2) Slide the throttle pushrod wire into the tube. Position the engine between the mounts. Use four M3x25mm machine screws to secure the engine to the mount as shown. Pushrod wire INSTALLING RETRACTABLE LANDING GEAR (OPTIONNAL).
Seagull de Havilland Mosquito Twin Engine RC Warbird 14 Instruction Manual.
COWLING 1) Slide the iberglass cowl over the engine and line up the back edge of the cowl with the marks you made on the fuselage then trim and cut as shown. cut. Trim and cut.
Seagull de Havilland Mosquito Twin Engine RC Warbird Trim and cut. Because of the size of the cowl, it may be necessary to use a needle valve extension for the high speed needle valve. Make this out of suicient length 1.5mm wire and install it into the end of the needle valve. Secure the wire in place by tightening the set screw in the side of the needle valve. 2) While keeping the back edge of the cowl lush with the marks, align the front of the cowl with the crankshat of the engine.
Machine screw m3 X10mm. Needle valve.
Seagull de Havilland Mosquito Twin Engine RC Warbird 18 Instruction Manual.
ELECTRIC POWER CONVERSION. 1) Locate the items neccessary to install the electric power conversion included with your model. 2) Recommend the items necessary to install the electric power conversion parts included with your model.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. - Motor: 35-45 size 830 rev per volt -ESC: 50A -Lipo 4s 3200mA -Elecric propeller:10x7 3) Attach the electric motor box to the irewall suitable with the cross lines drawn on the electric motor box and irewall. Using epoxy and balsa stick to secure the motor box to the irewall. Please see pictures below. 4 mm hen, use 5.5mm drill bit to enlarge the holes on the electric motor box. 5.5mm M5x25mm and washers. Blind nut.
M4x20mm 118mm Balsa stick Epoxy M4x20mm 21
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. HINGING THE ELEVATORS. Glue the elevator hinges in place using the same techniques used to hinge the ailerons.
INSTALL ELEVATOR CONTROL HORN. Draw center line 2) Using a modeling knife, carefully remove the covering at mounting slot of horizontal stabilizer ( both side of fuselage). Fiberglass control horn Epoxy. Cut. 3) Slide the stabilizer into place in the precut slot in the rear of the fuselage. he stabilizer should be pushed irmly against the front of the slot. Epoxy. INSTALLING THE HORIZONTAL STABILIZER.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. 7) When you are sure that everything is aligned correctly, mix up a generous amount of 30 Minute Epoxy. Apply a thin layer to the top and bottom of the stabilizer mounting area and to the stabilizer mounting platform sides in the fuselage. Slide the stabilizer in place and realign. Double check all of your measurements once more before the epoxy cures.
INSTALL RUDDER CONTROL HORN. Repeat steps to install the rudder control horn as same as steps done for ailerons. 1) Using a modeling knife, remove the covering from over the precut hinge slot cut into the lower rear portion of the fuselage. his slot accepts the lower rudder hinge. Remove covering. Fill Epoxy. Fiberglass control horn 2) While holding the vertical stabilizerirmly in place, use a pen and draw a line on each side of the vertical stabilizer where it meets the top of the fuselage.
Instruction Manual. Seagull de Havilland Mosquito Twin Engine RC Warbird 2) Position the elevator control horn on the both side of elevator. Horizontal Stabilizer. 90º Vertical Stabilizer. 3) hread one clevis and M2 lock nut on to each elevator control rod. hread the horns on until they are lush with the ends of the control rods. 4) Elevator and rudder pushrods assembly as pictures below. 4) When you are sure that everything is aligned correctly, mix up a generous amount of Flash 30 Minute Epoxy.
RUDDER PUSHROD ISTALLATION. Repeat steps as same as steps done for elevator.
Seagull de Havilland Mosquito Twin Engine RC Warbird MOUNTING THE TAIL WHEEL. Locate items necessary to install tail wheel. 28 Instruction Manual.
LED LIGHT.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. Wing tube. ATTACHMENT WING-FUSELAGE. Attach the aluminium tube into fuselage. INSTALLATION CANOPY, PANEL AND SEATS. 1) Locate items necessary to install canopy and seats.
Seagull de Havilland Mosquito Twin Engine RC Warbird 32 Instruction Manual.
APPLY THE DECALS. 1) If all the decals are precut and ready to stick. Please be certain the model is clean and free from oily ingerprints and dust. Position decal on the model where desired, using the photos on the box and aid in their location. 2) If all the decals are not precut, please use scissors or a sharp hobby knife to cut the decals from the sheet. Please be certain the model is clean and free from oily ingerprints and dust.
Instruction Manual. Seagull de Havilland Mosquito Twin Engine RC Warbird *If possible, irst attempt to balance the model by changing the position of the receiver battery and receiver. If you are unable to obtain good balance by doing so, then it will be necessary to add weight to the nose or tail to achieve the proper balance point.
FLIGHT PREPARATION. PREFLIGHT CHECK. Check the operation and direction of the elevator, rudder, ailerons and throttle. 1) Completely charge your transmitter and receiver batteries before your irst day of lying. A) Plug in your radio system per the manufacturer’s instructions and turn everything on. 2) Check every bolt and every glue joint in the Seagull de Havilland Mosquito Twin Engine RC Warbird to ensure that everything is tight and well bonded. B) Check the elevator irst.
Seagull de Havilland Mosquito Twin Engine RC Warbird Instruction Manual. If you have any queries, or are interested in our products, please feel free to contact us Factory : 12/101A - Hamlet 4 - Le Van Khuong Street - Dong hanh Ward Hoc Mon District - Ho Chi Minh City - Viet Nam. Oice : 62/8 Ngo Tat To Street - Ward 19 - Binh hanh District - Ho Chi Minh City - Viet Nam Phone : 848 - 86622289 or 848- 36018777 Website : www.SeagullModels.com Email : Sales@seagullmodels.com Facebook : www.facebook.