Code : SEA 327 ASSEMBLY MANUAL Wingspan--------------- 69 in (174.5 cm) Overall Length--------- 49.1 in (124.8 cm) Wing Arena------------- 612.3 sq.in (39.5 dm²) Flying Weight---------- 3.3 kg (7.3 lbs) Engine Size------------- 46-55 (2-stroke) 52-62 (4-stroke) 10cc (Gas) Radio-------------------- 5 channels with 7 servos Motor .35-.
Instruction Manual. Cessna Turbo Skylane 182 INTRODUCTION hank you for choosing the Cessna Turbo Skylane 182 ARTF by SG MODELS . he Cessna Turbo Skylane 182 was designed with the intermediate/advanced sport lyer in mind. It is a semi scale airplane which is easy to ly and quick to assemble. he airframe is conventionally built using balsa, plywood to make it stronger than the average ARTF, yet the design allows the aeroplane to be kept light.
KIT CONTENTS SEA362 Cessna Turbo Skylane 182 1. Fuselage 2. Wing set (2) 3. Tail set (2) 4. Canopy (2) 5. Cowling 6. Wing tube 7. Landing gear 8. Nose Landing gear 9. Fuel tank 10. Pushrod set 11. Ep Motor box 12. Windows 13. Spinner � � � � � HINGING THE FLAP Note : he control surfaces, including the ailerons, elevators, and rudder, are prehinged with hinges installed, but the hinges are not glued in place.
Instruction Manual. Cessna Turbo Skylane 182 - Repeat this process with the other wing panel, securely hinging the aileron in place. 3. T-pin - Ater both lap are securely hinged, irmly grasp the wing panel and aileron to make sure the hinges are securely glued and cannot be pulled out. Do this by carefully applying medium pressure, trying to separate the lap from the wing panel. Use caution not to crush the wing structure. - Delect the lap and completely saturate each hinge with thin C/A glue.
- Remove each hinge from the wing panel and aileron and place a T-pin in the center of each hinge. Slide each hinge into the wing panel until the T-pin is snug against the wing panel. his will help ensure an equal amount of hinge is on either side of the hinge line when the aileron is mounted to the aileron.
Instruction Manual. Cessna Turbo Skylane 182 - Turn the wing panel over and delect the aileron in the opposite direction from the opposite side. Apply thin C/A glue to each hinge, making sure that the C/A penetrates into both the aileron and wing panel. 2. - Using C/A remover/debonder and a paper towel, remove any excess C/A glue that may have accumulated on the wing or in the aileron hinge area. - Repeat this process with the other wing panel, securely hinging the aileron in place. 3.
2. Mininum servo spec. Torque : 66.6 oz-in (4.8 kg-cm) @ 4.8V; 83.3 oz-in (6.0 kg-cm) @ 6.0V Because the size of servos difer, you may need to adjust the size of the precut opening in the mount. he notch in the sides of the mount allow the servo lead to pass through. INSTALLING THE AILERON SERVOS - Place the servo between the mounting blocks and space it from the hatch. Use a pencil to mark the mounting hole locations on the blocks. 1. 3. 2.
Instruction Manual. Cessna Turbo Skylane 182 - Remove the string from the wing at the servo location and use the tape to attach it to the servo extension lead. Pull the lead through the wing and remove the string. 5. 9. C/A glue - Use dental loss or heatshrunk tube to secure the connection so they cannot become unplugged. 6. 10. - Secure the servo to the aileron hatch using Phillips screwdriver and the screws provided with the servo. 7. 11.
2. 12. - Set the aileron hatch in place and use a Phillips screw driver to install it with four wood screws. 3. 13. 2x10mm Hex nut M2 clevis Fuel tubing INSTALLING THE FLAP PUSHROD 14. - Repeat the procedure for the aileron pushrod. 1. 70mm 2. AILERON PUSHROD INSTALLATION - Please see below pictures. 1.
Instruction Manual. Cessna Turbo Skylane 182 WHEELS AND WHEEL PANTS 5. - Assemble and mounting the landing gear, wheels to the wheel pants as shown inthe following pictures. 1. 6. Cut 2. 7. 3. 8. 4.
9. 13. 10. 14. 11. 15. head locker glue C/A glue 12. 16.
Instruction Manual. Cessna Turbo Skylane 182 17. 21. 18. 22. C/A glue 19. 23. 20. 24.
25. 29. 26. 30. 27. 31. 28. INSTALL NOSE GEAR - Locate the items necessary to attach the nose landing gear that are included with your model.
Instruction Manual. Cessna Turbo Skylane 182 1. 5. 2. 6. 3. 7. 3x4mm 4. 14 8.
9. 13. 10. 14. 11. 15. head locker glue 12. 16.
Instruction Manual. Cessna Turbo Skylane 182 17. 21. 18. 22. 3x4mm 19. 23. 20. 24.
25. 29. 26. 30. 27. 31. 28. 32.
Instruction Manual. Cessna Turbo Skylane 182 33. 1. Rudder servo Tail wheel hrottle servo Elevator servo - Secure the servos with the screws provided with your radio system. 34. 2. hrottle servo Elevator servo Rudder servo 35. THROTTLE SERVO ARM INSTALLATION - Install adjustable servo connector in the servo arm as same as picture below: 1. INSTALLING THE FUSELAGE SERVOS Because the size of servos difer, you may need to adjust the size of the precut . opening in the mount.
2. INSTALLING THE STOPPER ASSEMBLY Rudder servo arm - Using a modeling knife, carefully cut of the rear portion of one of the 3 nylon tubes leaving 1/2” protruding from the rear of the stopper. his will be the fuel pick up tube. - Using a modeling knife, cut one length of silicon fuel line. Connect one end of the line to the weighted fuel pick up and the other end to the nylon pick up tube. Elevator servo arm hrottle servo arm INSTALLING THE RECEIVER SWITCH 1.
Instruction Manual. Cessna Turbo Skylane 182 4. Vent tube. - Slide the fuel tank into the fuselage. Guide the lines from the tank through the hole in the iewall. Fuel pick up tube. - Use plywood template to hold in place the fuel tank with C/A glue to secure the fueltank inside the fuselage. Fuel fill tube. - Carefully bend the second nylon tube up at a 45º angle. his tube is the vent tube. 2. - Test it the stopper assembly into the tank.
5. 2. Vent tube Fuel pick up tube Fuel ill tube - Connect the lines from the tank to the engine and muler. he vent line will connect to the muler and the line from the clunk tothe carburetor. 4mm - Use a drill to drill the four holes in the engine mount rails. 3. Blow through one of the lines to ensure the fuel lines have not become kinked inside the fuel tank compartment. Air should low through easily.
Instruction Manual. Cessna Turbo Skylane 182 8. 4. - Reinstall the servo horn by sliding the connector over the pushrod wire. Center the throttle stick and trim and install the servo horn perpendicular to the servo center line. 5. Pushrod wire 9. 4x25mm 6. M4 lock Nut - Move the throttle stick to the closed position and move the carburetor to closed. Use a 2.5mm hex wrench to tighten the screw that secures the throttle pushrod wire.
- Tape the cowl to the fuselage using lowtack tape. COWLING - Please see below pictures. 5. 1. - Use a drill and drill bit to drill the holes for the cowl mounting screws. Make sure the cowl position is correct before drilling each hole. 2. 6. 2mm 3. 4. - Install the muler and muler extension onto the engine and make the cutout in the cowl for muler clearance. Connect the fuel and pressure lines to the carburetor, muler and fuel iler valve.
Instruction Manual. Cessna Turbo Skylane 182 7. 11. 8. 12. 3x10mm 9. ELECTRIC POWER CONVERSION - Locate the items neccessary to install the electric power conversion included with your model. 1. 10. - Recommend the items necessary to install the electric power conversion parts included with your model.
- Motor: 35-45 (830 Watt) - ESC: 50A - Lipo Batteries: 4S 3200mA - Attach the electric motor box to the irewall centered with the cross lines drawn on the electric motor box and irewall. Using M4x25mm to secure the motor box to the irewall. Please see pictures below. 4. 5. 2. 6. 4mm 3. M4x25mm and washers - hen, use 4mm drill bit to enlarge the holes on the electric motor box.
Instruction Manual. Cessna Turbo Skylane 182 8. 11. Epoxy Blind nut 120mm - Attach the motor to the front of the electric motor box using four 4mm blind nut, four M3x15mm hex head bolts to secure the motor. Please see picture shown. 12. Balsa stick Epoxy 9. - Attach the speed control to the side of the motor box using two-sided tape and tie wraps. Connect the appropriate leads from the speed control to the motor. Make sure the leads will not interfere with the operation of the motor. 10.
1. 14. 15. he propeller should not touch any part of the spinner cone. If it does, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it. Battery 2. 16. INSTALLING THE HORIZONTAL STABILIZER INSTALLING THE SPINNER - Install the spinner backplate, propeller and spinner cone. - Using a ruler and a pen, locate the centerline of the horizontal stabilizer, at the trailing edge, and place a mark.
Instruction Manual. Cessna Turbo Skylane 182 1. 5. 2. 6. Pen 3. 7. Pen 4. 28 8.
9. 13. 10. 14. 11. 15. 12. 16.
Instruction Manual. Cessna Turbo Skylane 182 17. 1. C/A glue 18. 2. 19. 3. HINGING THE RUDDER - Glue the top two rudder hinges in place using the same techniques used to hinge the ailerons. - he lower hinge will be glued when the i/rudder assembly is attached to the fuselage. 30 4.
5. 9. C/A glue 6. 10. Pen 11. 7. 12. 8.
Instruction Manual. Cessna Turbo Skylane 182 13. 17. C/A glue ELEVATOR PUSHROD INSTALLATION 14. - Install the elevator control horn using the same method as with the aileron control horns. - Position the elevator control horn on the both side of elevator. 1. 15. Fiberglass control horn - Locate items necessaryto install rudder pushrod. 2. 16. C/A glue - Install the elevator control horn using the same method as with the aileron control horns.
- Position the elevator control horn on the both side of elevator. 6. 3. 7. 4. 8. - head one clevis and M2 lock nut on to each elevator control rod. head the horns on until they are lsh with the ends of the control rods. - Elevator and rudder pushrods assembly as pictures below. 5. 9.
Instruction Manual. Cessna Turbo Skylane 182 RUDDER PUSHROD INSTALLATION INSTALL THE WINDOW Parts requirement.See pictures below. - Locate items necessaryto install rudder pushrod. 1. 1. 625mm 2. 2. 3. 3. 4.
4. 8. 5. 9. 6. 10. C/A glue 7. C/A glue 11.
Instruction Manual. Cessna Turbo Skylane 182 4. INSTALLATION CANOPY - Locate items necessary to install canopy. 1. C/A glue 5. 2. 8mm 6. 3. 7.
2. 8. Receiver Battery C/A glue 9. ATTACHMENT WING- FUSELAGE - Locate items necessary to intall tail wheel. 1. Wing tube INSTALLING BATTERY - RECEIVER - Plug the servo leads and the switch lead into the receiver. Plug the battery pack lead into the switch also. - Wrap the receiver and battery pack in the protective foam rubber to protect them from vibration. - Insert two wing panels as pictures below. 2. 1.
Instruction Manual. Cessna Turbo Skylane 182 3. 1. 4. 2. 5. 3. Wing bolt INSTALLATION WING- FUSELAGE STRUTS - Parts requirement.See pictures below. 38 4.
5. 9. 6. 10. 7. 11. 8. 12.
Instruction Manual. Cessna Turbo Skylane 182 13. 17. 14. 18. 2x8mm 15. 19. 16. 20.
21. 25. 2x8mm 22. APPLY THE DECALS - If all the decals are precut and ready to stick. Please be certain the model is clean and free from oily ingerprints and dust. Position decal on the model where desired, using the photos on the box and aid in their location. 23. - If all the decals are not precut, please use scissors or a sharp hobby knife to cut the decals from the sheet. Please be certain the model is clean and free from oily ingerprints and dust.
Cessna Turbo Skylane 182 2) he recommended Center of Gravity (CG) location for your model is (80mm) back from the leading edge at the center of the wing. 3) When balancing your model, make sure it is assembled and ready for light. Support the plane upright at the marks made on the wing with your igers or a commercially available balancing stand. his is the correct balance point for your model. *If possible, irst attempt to balance the model by changing the position of the receiver battery and receiver.
15-20mm 15-20mm Fuselage Wing 25-30mm 25-30mm 15-20mm 15-20mm 30mm 43
Cessna Turbo Skylane 182 Instruction Manual. FLIGHT PREPARATION PREFLIGHT CHECK Check the operation and direction of the elevator, rudder, ailerons and throttle. 1) Completely charge your transmitter and receiver batteries before your irst day of lying. A) Plug in your radio system per the manufacturer’s instructions and turn everything on. B) Check the elevator irst. Pull back on the elevator stick. he elevator halves should move up.
If you have any queries, or are interested in our products, please feel free to contact us Factory : 12/101A - Hamlet 4 - Le Van Khuong Street - Dong hanh Ward Hoc Mon District - Ho Chi Minh City - Viet Nam. Oice : 62/8 Ngo Tat To Street - Ward 19 - Binh hanh District - Ho Chi Minh City - Viet Nam Phone : 848 - 86622289 or 848- 36018777 Website : www.SeagullModels.com Email : Sales@seagullmodels.com Facebook : www.facebook.com/SeaGullModels.
