Use and Care Manual

PRODUCT
DATA SHEET
DESCRIPTION: Durable & decorative floor paint for concrete & masonry surfaces; water-
based acrylic-epoxy blend.
Typical Uses:
3 Garage & Shop Floors 3 Driveways/Carports
3 Pool Decks 3 Patios & Porches
3 Walkways 3 Basements
Important: Read all directions thoroughly. Recommended: Wear gloves and safety glasses.
SURFACE PREP*: Note: Proper surface prep is critical to product performance. The surface
should be clean, dry, sound and free of dirt, dust, oil, wax and grease. You may need an oil
stain remover to lift stubborn oil stains.
Bare Concrete: Concrete must have cured for a minimum of 30 days before application.
Etch the surface with SEAL-KRETE Clean-N-Etch to allow for proper penetration and
adhesion. Etching is especially important for smooth-troweled concrete surfaces (like
carports, garage and basement floors) and is also recommended for rough-finished
surfaces. After etching, rinse the surface thoroughly and let dry. For best adhesion results,
apply one thin coat of SEAL-KRETE Lock-Down
™
Concrete Bonding Primer.
Previously Stained Or Painted Concrete: For use over one-part water-based coatings
only; not recommended over oil-based coatings. Remove loose or peeling paint and
degloss surface by sanding (150–200 grit paper).** Follow with a general cleaning. Rinse
thoroughly and let dry. Then coat the surface with SEAL-KRETE Lock-Down Concrete
Bonding Primer.
APPLICATION: Read “LIMITATIONS” section before use. This product is ready to use; do not
dilute. Use only when air and surface temperatures are 50-90 F (10 to 32 C). If more than one
gallon is used, intermix all product to ensure color uniformity; stir well. Apply a very thin coat
with a roller** or nylon-polyester brush. Wait 4–6 hours.*** Apply second coat in a direction
perpendicular to the first.
** Use 1/4” nap for smooth-troweled surface, 3/8” nap for broom-finished surface, 1/2” nap for
rough or textured surface.
***Additional dry time is needed in lower temperatures or when relative humidity is more than 50%.
COVERAGE: 300–500 sq.ft. per gallon, depending on surface porosity.
DRY TIME: Dry to the touch in 2 hours at 77°F (25°C) 50% RH. Dry to light foot traffic in
24 hours, heavy foot traffic in 72 hours. Allow a minimum of 5 days before subjecting to
automotive traffic. Premature traffic could cause paint to lift.
TINT LIMITS: White Base: Up to 5 oz. colorant per gallon. Deep Base: Up to 8 oz. colorant
per gallon.
CLEAN-UP & STORAGE: Clean tools with soap and water. Contact your household refuse
collection service for disposal of empty containers and unused paint. Important: Wait 30
days before rinsing or cleaning surface. To avoid premature paint failure, do not use abrasive
cleaners or pressure-washer on surface. KEEP FROM FREEZING.
LIMITATIONS: Temperature should be 50° to 90°F (10° to 32°C) and should not fall below
50°F (10°C) within 24 hours of application. Do not apply if rain is expected within 24 hours.
Use only with one component (or one part) water-based products. Not recommended for
wood, metal, glazed surfaces or areas subject to standing water or hydrostatic pressure.
Areas receiving heavy tire traffic should be coated with an approved SEAL-KRETE clear sealer.
* Sanding or removing paint containing lead may be hazardous. For information contact
the National Lead Information Center at 1-800-424-LEAD or www.epa.gov/lead.
WARNING! IRRITANT! CONTAINS EPOXY RESIN AND ACRYLATES.
CAUTION: KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY. USE WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors
or use other means to ensure fresh air entry during application and drying. If you experience
eye watering, headache or dizziness, increase fresh air and use a properly fitted respirator
(NIOSH-approved for organic vapor with P Series particulate prefilter). Obtain professional
advice before using. A dust mask does not provide protection against vapors. Avoid contact
with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty breathing, leave the area to obtain fresh air. If
continued difficulty occurs, get medical attention immediately. In case of eye contact, flush
immediately with plenty of water for 15 minutes and get medical attention. For skin contact,
wash thoroughly with soap and water. If swallowed, get medical attention immediately.
Epoxy-Seal Slate Gray No. 962 317395 1 gallon 020066349899 10020066353794 13.94 x 14 x 8.5 0.96/42.48 4 45 cs
Epoxy-Seal Armor Gray No. 961 317396 1 gallon 020066349905 10020066353800 13.94 x 14 x 8.5 0.96/42.48 4 45 cs
Epoxy-Seal White Base No. 960 317397 1 gallon 020066349912 10020066353817 13.94 x 14 x 8.5 0.96/42.48 4 45 cs
Epoxy-Seal Deep Base No. 970 317398 1 gallon 020066350024 10020066353824 13.94 x 14 x 8.5 0.96/42.48 4 45 cs
Epoxy-Seal Slate Gray No. 962 351217 5 gallon 020066450359 - - 1.35/50.49 1 36
Epoxy-Seal Armor Gray No. 961 351218 5 gallon 020066450342 - - 1.35/50.99 1 36
Epoxy-Seal White Base No. 960 351219 5 gallon 020066450366 - - 1.35/49.24 1 36
Epoxy-Seal Deep Base No. 970 351220 5 gallon 020066450328 - - 1.35/45.99 1 36
Carton Size Cube / Wt.
Product No. Unit UPC Code Carton Bar Code ( W x D x H ) ( cubic ft / lbs ) Carton Qty Pallet Qty
www.seal-krete.com