Use and Care Manual

DESCRIPTION: Clear protective satin finish for concrete paints, stains
and textured coatings; premium water-based acrylic. Ideal for use over
SEAL-KRETE
®
Floor-Tex textured concrete coating to extend life of coating
and protect against wear.
Typical Uses:
3 Pool Decks 3 Patios & Porches
3 Driveways & Garages 3 Sidewalks
Important: Read all directions thoroughly. Recommended: Wear gloves and
safety glasses.
SURFACE PREP*: Note: The surface should be clean and dry. You may need
an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn oil
stains. Pressure-washing is recommended.
Bare Concrete: Concrete must have cured for a minimum of 30 days.
Etch smooth-finished concrete (such as basement or garage floors) with a
concrete etching solution like SEAL-KRETE Clean-N-Etch. Note: If etching
with muriatic acid the area must be neutralized before proceeding. For
more information visit www.seal-krete.com.
Painted Surfaces: For use over one-part water-based coatings only
and ideal for use over SEAL-KRETE Floor-Tex textured coating. Not
recommended over acid-based stains or oil-based coatings. Freshly
painted surfaces must have cured for a minimum of 24 hours. Paint must
be sound (not blistering or peeling). Existing painted surfaces should be
cleaned with a solution of Trisodium Phosphate (TSP) and water. Rinse well
and allow to dry.
APPLICATION: Read “LIMITATIONS” section before use. This product is ready
to use; do not dilute. Apply in light, even coats. One coat is recommended;
however, over porous surfaces (like saltillo tile) or when a higher sheen is
desired, apply a second coat. Note: Sealer goes on milky white but dries clear.
Roller: Dampen roller, remove excess water, then saturate roller with
product. Keep a wet edge while rolling. Do not allow to puddle, foam or
run. (Use a 1/4” nap for smooth surfaces, 3/8” nap for rough or porous
surfaces.)
Pump Sprayer: Set at a fine spray and apply using a circular motion.
To eliminate puddling or to achieve a more uniform finish, backroll
immediately after spraying.
COVERAGE: 150–300 sq.ft. per gallon, depending on surface porosity.
DRY TIME: Dry to touch in 1 hour at 77°F (25°C) 50% RH. Recoat in 2 hours.
Dry to foot traffic in 24 hours. Will accept vehicular traffic in 72 hours. Dry
times should be extended in colder climates.
CLEAN-UP & STORAGE: Clean tools with soap and water immediately after
use. Store in a dry area. KEEP FROM FREEZING.
MAINTENANCE: Clean with a mild soap and water solution. Do not use
solvent-based cleaners.
LIMITATIONS: Temperatures should be between 50°–90°F (10°–32°C) and
should not fall below 50°F (10°C) within 24 hours of application. Do not apply
if rain is expected within 12 hours. Do not use over acid-based stains or two
part water-based or solvent-based epoxy coatings. Do not use on glazed
tile. Do not use in areas subject to hydrostatic pressure. Smooth-finished
concrete may be slippery when wet; consider using an anti-skid additive like
SEAL-KRETE Clear Grip on high foot traffic areas.
*Sanding or removing paint containing lead may be hazardous. For
information contact the National Lead Information Center at 1-800-424-LEAD
or www.epa.gov/lead.
CAUTION: Contains Di-propylene Glycol Mono-N-Propyl Ether and
1-phenoxy-2-propanol. Irritating to skin, eyes and respiratory system. Wear
suitable protective clothing, gloves and eye or face protection. FIRST AID:
Skin Contact: Wash off immediately with soap and water. Seek medical
attention in the event of rashes or persistent irritation. Eye Contact: Flush
eyes repeatedly with lukewarm water. Seek medical attention. If Swallowed:
Do not induce vomiting, give 1–2 glasses of water if conscious. Seek medical
attention.
KEEP OUT OF REACH OF CHILDREN AND PETS. DO NOT TAKE INTERNALLY.
www.seal-krete.com
PRODUCT
DATA SHEET
CLEAR PROTECTIVE SEALER
CLEAR PROTECTIVE SEALER
TOPCOATTOPCOATTOPCOAT
FLOOR-TEX
Floor-Tex Topcoat Sealer 402001 1 gallon 0 15944 40201 8 9 00 15944 40201 1 15 x 9.5 x 13 1.07 / 37.03 4 36 cs
Floor-Tex Topcoat Sealer
402005 5 gallon 0 15944 40205 6 – 12.5 x 12.15 x 14.75 1.30 / 45.67 1 36 ea
Carton Size Cube / Wt.
Product No. Unit UPC Code Carton Bar Code ( W x D x H ) ( cubic ft / lbs ) Carton Qty Pallet Qty