Use and Care Manual

PRODUCT
DATA SHEET
DESCRIPTION: Clear protective fi nish for painted, stained or bare concrete &
masonry surfaces; premium water-based urethane-fortifi ed acrylic. Available
in Satin & Gloss sheens.
Typical Uses:
✓ Pool Decks ✓ Patios & Porches ✓ Brick & Stone
✓ Driveways & Garages ✓ Exposed Aggregate ✓ Slate & Saltillo
✓Pavers & Stamped Concrete
Important: Read all directions thoroughly. Recommended: Wear gloves and
safety glasses.
SURFACE PREP*: Note: The surface should be clean and dry. You may need
an oil stain remover such as SEAL-KRETE
®
Oil Stain Remover to lift stubborn
oil stains. Pressure-washing is recommended.
Bare Concrete: Concrete must have cured for a minimum of 30 days.
Etch smooth-fi nished concrete (such as basement or garage fl oors) with a
concrete etching solution like SEAL-KRETE Clean-N-Etch. Note: If etching
with muriatic acid the area must be neutralized before proceeding. For
more information visit www.seal-krete.com.
Painted Surfaces: For use over one-part water-based coatings only;
not recommended over acid-based stains or oil-based coatings. Freshly
painted surfaces must have cured for a minimum of 72 hours. Paint must
be sound (not blistering or peeling). Existing painted surfaces should be
cleaned with a solution of Trisodium Phosphate (TSP) and water. Rinse
well and allow to dry.
APPLICATION: Read “LIMITATIONS” section before use. This product is ready
to use; do not dilute. Stir gently; do not shake. Apply in light, even coats. One
coat is recommended; however, over porous surfaces (like saltillo tile) or
when a higher sheen is desired, apply a second coat. Note: Sealer goes on
milky white but dries clear.
Roller: Dampen roller, remove excess water, then saturate roller with
product. Keep a wet edge while rolling. Do not allow to puddle, foam or
run. (Use a 1/4” nap for smooth surfaces, 3/8” nap for rough or porous
surfaces.)
Pump Sprayer: Set at a fi ne spray and apply using a circular motion.
To eliminate puddling or to achieve a more uniform fi nish, backroll
immediately after spraying.
COVERAGE: 150–300 sq.ft. per gallon, depending on surface porosity.
DRY TIME: Dry to touch in 1 hour at 77°F (25°C) 50% RH. Recoat in 2 hours.
Dry to foot traffi c in 24 hours. Will accept vehicular traffi c in 72 hours. Dry
times should be extended in colder climates.
CLEAN-UP & STORAGE: Clean tools with soap and water immediately after
use. Store in a dry area. KEEP FROM FREEZING.
MAINTENANCE: Clean with a mild soap and water solution. Do not use
solvent-based cleaners.
LIMITATIONS: Temperatures should be 50° to 90°F (10° to 32°C) and should
not fall below 50°F (10°C) within 24 hours of application. Do not apply if rain
is expected within 12 hours. Do not use over acid-based stains, 2-part epoxies
or oil-based paints. Do not use on glazed tile. Do not use in areas subject to
hydrostatic pressure. Smooth-fi nished concrete may be slippery when wet;
consider using an anti-skid additive like SEAL-KRETE Clear Grip on high foot
traffi c areas.
*Sanding or removing paint containing lead may be hazardous. For information
contact the National Lead Information Center at 1-800-424-LEAD or www.
epa.gov/lead.
CAUTION: EYE IRRITANT. Contains Dipropylene Glycol N-Propyl Ether.
Avoid contact with eyes and prolonged contact with skin. Do not ingest.
FIRST AID: In case of eye contact, fl ush with water for 15 minutes. If irritation
persists, get medical attention. In case of skin contact, wash thoroughly with
soap and water. If swallowed, drink 1-2 glasses of water and immediately
contact medical services regarding any instructions to induce vomiting.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
Clear-Seal Satin Protective Sealer 604001 1 gal 0 15944 60401 6 1 00 15944 60401 3 14.38 x 14.38 x 8.5 1.02 / 36.68 4 45 cs
Clear-Seal Satin Protective Sealer 604005 5 gal 0 15944 60405 4 — — 1.35 / 45.17 1 36 ea
Clear-Seal Gloss Protective Sealer 606001 1 gal 0 15944 60601 0 1 00 15944 60601 7 14.38 x 14.38 x 8.5 1.02 / 38.13 4 45 cs
Clear-Seal Gloss Protective Sealer 606005 5 gal 0 15944 60605 8 — — 1.35 / 45.17 1 36 ea
Clear-Seal Gloss Protective Sealer Low VOC 607001 1 gal 0 15944 60701 7 1 00 15944 60701 4 14.38 x 14.38 x 8.5 1.02 / 37.79 4 45 cs
Carton Size Cube / Wt.
Product No. Unit UPC Code Carton Bar Code ( W x D x H ) ( cubic ft / lbs ) Carton Qty Pallet Qty
CONCRETE PROTECTIVE SEALERCONCRETE PROTECTIVE SEALER
CONCRETE PROTECTIVE SEALER
CLEAR-SEALCLEAR-SEAL
CLEAR-SEAL
Also Available
in a Low VOC Formula
www.seal-krete.com