Warranty

6 3 7 8 4 3 9 5 0 0 5 8
For Use On
These Surfaces:
IMPORTANT - Read entire label before using. Application temperature must be a minimum
of 60°F and rising. Do not apply when temperature is expected to drop below 60°F within
a 24 hour period. In areas where dew or fog accumulates in the early evening, it is best to
coat in the morning. Stop coating by early afternoon (3:00 pm) to prevent wash off, which
will occur if dew, fog, or rain arrives before coating dries. Do not apply if rain is imminent
or forecast within 24 hours of application. Be sure to wear eye protection when mixing or
applying roof coating.
DESCRIPTION - SealBest Premium Professional Grade White Elastomeric Roof Coating is
a superior performing product featuring unmatched adhesion, low temperature exibility and
durability. This product exceeds the stringent performance specications required by ASTM-
D6083. Forms a tough, durable rubber membrane over a variety of roof surfaces.
USES - EDPM rubber roofs, polyurethane foam, APP and SBS modied bitumen, asphalt,
mobile homes and RV’s, concrete, wood and more.
NOTE: This product is not recommended for gravel, dead level (flat), or shingled roof
surfaces.
COVERAGE - One 4.75-gallon pail will coat approximately 250-350 square feet of roof
surface.
DIRECTIONS:
Clean Roof - Sweep off all dirt, dust, and debris. Remove rust, mildew, oil, grease, or other
foreign material on the surface. Allow freshly applied asphalt roofs to cure a minimum of 4
weeks prior to applying this coating. Scrub roof with SealBest Concentrated Roof Cleaner
or bleach solution (1 part chlorine bleach and 3 parts water). Rinse thoroughly and allow to dry.
EPDM ROOFS: When coating EPDM roofs it is extremely important to remove all dust,
dirt, and embedded clay to assure proper adhesion. Thoroughly scrub roof surface with
SealBest Concentrated Roof Cleaner or bleach solution (1 part chlorine bleach and 3 parts
water) and pressure wash entire roof surface. Use a wide tip on pressure washer to prevent
tearing roof material. Allow surface to dry.
Applying Roof Coating - Stir pail thoroughly. Do not dilute. For best results apply White
Elastomeric Roof Coating with a soft brush, 3/4” nap paint roller, or high pressure sprayer.
For optimum performance, durability and warranty purposes, apply a second coat.
CLEAN UP - Wash tools with water before material dries.
CHEMICAL COMPOSITION - Water CAS #7732-18-5, 100% acrylic emulsion polymer
(proprietary), Limestone CAS #16389-88-1, Titanium Dioxide CAS #13463-67-7, Ester
Alcohol CAS #25265-77-4. This product contains less than 100 grams per liter of volatile
organic compounds (VOC).
FIRST AID - IN EYE: Immediately ush with large amounts of water for at least 15 minutes.
Immediately seek medical attention. ON SKIN: Wash thoroughly with soap and water or
hand cleaner (if material has dried). If irritation or rash develops, seek medical attention.
IF INHALED: Remove person from exposure. If breathing has stopped or is difcult,
administer articial respiration or oxygen as needed. Seek medical aid. IF INGESTED: Do
not induce vomiting. Seek medical aid immediately.
RESTRICTIONS - PROTECT CONTAINER FROM FREEZING.
ATTENTION - Empty containers may retain material residues. Dispose of empty container
in accordance with local, state, and federal regulations based upon chemical composition of
contents.
CAUTION - Avoid breathing vapors and contact with eyes and skin. Do not take internally.
Clean hands thoroughly after using. If material gets in eyes or mouth call a physician
immediately. Use with adequate ventilation. KEEP OUT OF REACH OF CHILDREN.
WARNING - Children can fall into pail and drown. Keep children away from pail with even a
small amount of liquid.
WARRANTY - The statements made on this label are believed to be true and accurate, and are
intended to provide a guide for approved construction practices. The manufacturer does not make, nor
does it authorize any agent or representative to make any warranty, express or implied, concerning this
material as workmanship, weather, tools utilized and other variables affecting results are beyond our
control. The manufacturer warrants that this product shall be free from material defects for a period of 15
years from date of purchase, when applied in accordance with instructions on this label over a sound,
properly prepared, non-at compatible roof surface, with a minimum of TWO COATS applied, and patch
work performed with Roof Patch and Fabric. Should the original purchaser of this product discover that
this product has not performed as advertised herein, the purchaser shall promptly notify the manufacturer
in writing of that event, provide details of the nature of the failure and provide proof of product purchase.
If the manufacturer’s products are found to be defective, the manufacturer will provide option: 1)
replacement product to sufciently correct the failure or 2) a prorated refund of the original purchase price
of the product. This constitutes the purchaser’s sole remedy. In no event shall the manufacturer be liable
for any injury, loss or damage, either direct or incidental in connection with use of this material.
Manufactured by:
ThorWorks Industries • 2520 S. Campbell St. • Sandusky, OH 44870
•FormsADurable
 RubberMembrane
•MeetsASTMD6083
•SuperiorQualityIndustrial
 FormulaFeaturingThe
 HighestSolidsFor
 MaximumFilmBuild
APPLYBYROLLER,
BRUSH,ORSPRAY
100% Acrylic
PROFESSIONAL
GRADE
YEAR PROTECTION
White Elastomeric
ROOF
Coating
4.75 U.S. Gallon
(17.96 Liters)
White
Elastomeric
ROOF
White
Elastomeric
ROOF
Sweep off all dirt,
dust, and debris.
Scrub roof with
SealBest Roof
Cleaner or
Bleach Solution.
Rinse surface
thoroughly.
Repair cracks
and seams with
SealBest Roof
Patch.
Stir roof coating
thoroughly.
Apply roof coating
with roller, brush
or spray.
For more installation tips visit
sealbest.com
USA
MADE
IN THE
For more installation tips
scan this QR code with
your smartphone or visit
www.sealbest.com