User Manual

4.1. Fit the handle assembly into the handle socket with the valve control lever towards the jack. Retain with the handle fixing

bolt. See fig.1.

4.2. Before using the jack for the first time, purge the hydraulic circuit in order to eliminate any air in the system. To do this, open

the release valve by moving the lever downwards from position A to position B as shown in fig.2. In the lower position B the handle

must engage with one of the 3 handle locations indicated in fig.1. Once engaged the release valve can be opened by rotating the

lever fully sideways as shown in fig.2-C. Pump the foot pedal through its full travel 3 or 4 times. Return the release valve lever to

the upper closed position (see fig.2-A)

Model: ................... 10QJ.V2

Capacity:.................. 10tonne

Min. Saddle Height: .......... 160mm

Max. Saddle Height:.......... 560mm

Max. Chassis Height: ....... 250mm

Length:… ................. 1637mm

Weight: ..................... 129kg

3 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.

Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.

3 Locate the jack in a suitable, well lit work area.

3 Keep work area clean and tidy and free from unrelated materials.

3 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.

3 Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).

3 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear (“PARK” if automatic).

3 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.

3 Ensure there are no passengers in the vehicle.

3 Ensure all non-essential persons keep a safe distance whilst the jack is in use.

3 Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).

3 Check the lifting point is stable and centred on the jack saddle.

3 Ensure the jack wheels are free to move and that there are no obstructions.

p DANGER: Use the jack for lifting only, NOT for supporting the lifted load.

3 Use suitable capacity axle stands under the vehicle before proceeding with any task.

3 Ensure there are no persons or obstructions beneath the vehicle before lowering.

3 Use a qualified person to maintain or repair the jack hydraulic system.

7 DO NOT operate the jack if damaged.

7 DO NOT allow untrained persons to operate the jack.

7 DO NOT exceed the rated capacity of the jack.

7 DO NOT allow the vehicle to move while supported by the jack, nor use the jack to move the vehicle.

7 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.

7 DO NOT work under the vehicle until axle stands have been correctly positioned.

7 DO NOT use the jack for purposes other than that for which it is designed.

7 DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.

7 DO NOT adjust the safety overload valve.

3 When not in use store jack, fully lowered, in a safe, dry, childproof area.

g.1

INSTRUCTIONS FOR:

TROLLEY JACK 10TONNE LONG REACH

MODEL NO: 10QJ.V3

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

4. ASSEMBLY

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

Refer to

instruction

manual

Heavy-duty chassis with one-piece hydraulic unit. Handle mounted safety release prevents inadvertent lowering of load. Includes large diameter

saddle for easier positioning under the jacking point. Foot operated quick lift system. Fitted with safety overload valve. Fully CE approved for

general workshop applications.

Original Language Version

10QJ.V3 Issue: 1 - 11/11/14

Summary of content (3 pages)

PAGE 1
INSTRUCTIONS FOR: TROLLEY JACK 10TONNE LONG REACH MODEL NO: 10QJ.V3 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Thank you for purchasing a Sealey product.
PAGE 2
4.3. Place a few drops of hydraulic jack oil on the pump piston and pump the handle several times to distribute the oil. Thoroughly lubricate all moving parts. 5. ASSEMBLY 5.1. p 5.1.1. General jacking. WARNING! Before lifting, ensure Section 1 safety instructions are strictly followed. Prepare vehicle as described in safety instructions ensuring the ground on which jack is to stand is level and solid (not tarmacadam). We recommend concrete. 5.1.2.
PAGE 3
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.