User Manual

ManualsBrandsSealey ManualsToolsSA27

INSTRUCTIONS FOR:

Ball Joint Removal/Installation Set

(Mercedes Sprinter)

Model No: VSE127H05

1. SAFETY INSTRUCTIONS

2. INTRODUCTION & SPECIFICATION

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give

you years of trouble free performance.

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE TOOL CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

 WARNING! Ensure Health and Safety, local authority and general

workshop practice regulations are adhered to when using tools.

 DO NOT use tools if damaged.

 Maintain tools in good and clean condition for best and safest

performance.

 Ensure that a vehicle which has been jacked up is adequately

supported with axle stands and that the wheels are chocked.

 Ensure that the rear axle is adequately supported, refer to the

vehicle manufacturer’s service instructions, or a proprietary

manual.

 Wear approved eye protection. A full range of personal safety

equipment is available from your Sealey dealer.

 Wear suitable clothing to avoid snagging. Do not wear jewellery

and tie back long hair.

 DO NOT use air tools to operate the force screw.

IMPORTANT: The force screw must be kept well lubricated.

IMPORTANT: This manual is provided as a guide only, refer to

the vehicle manufacturer’s service instructions, or a proprietary

manual, to establish the current procedure and data.

 WARNING! Failure to heed safety and warning instructions may

result in damage and/or personal

injury and will invalidate the

warranty.

 WARNING! The warnings, cautions & instructions referred

to in this manual cannot cover all possible conditions and

situations that may occur. It must be understood that

common sense and caution are factors which cannot be

built into this product, but must be applied by the operator.

Use in conjunction with Sealey Hydraulic Ball Joint Remover/Installer

Kit (Model No. VSE127H). Essential tool for removal/installation of the

Mercedes Sprinter front lower ball joint in situ. Includes all necessary

adaptors.

SPECIFICATION:

Model No. ....................................................................... VSE127H05

Model No. of associated Tool .............................................. VSE127H

Ball joint OE Number ....................................................... 9013330727

Application - Mercedes ............... Sprinter 901, 902, 903, 904 (95-on)

3. OPERATION

NOTE! Pictures taken with the lower arm / wishbone removed from

vehicle for clarity only.

NOTE! Before installing the new ball joint, refer to the vehicle

manufacturer’s service instructions, or a proprietary manual, to

establish the correct data and procedures.

VSE127H05 Issue No. 1 - 10/11/09



ALWAYS KEEP FORCE SCREW

WELL LUBRICATED.

DO NOT USE AIR TOOLS

Original Language Version

Fig.1

Fig.2

Summary of content (2 pages)

PAGE 1
INSTRUCTIONS FOR: Ball Joint Removal/Installation Set (Mercedes Sprinter) Model No: VSE127H05 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE TOOL CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
PAGE 2
Fig.3 3.1 Ball Joint Removal. To remove the ball joint you will need to use adaptors A & B in conjunction with Sealey Hydraulic Ball Joint Remover/Installer Kit (Model No. VSE127H). 3.1.1 Referring to the vehicle manufacturers servicing information disassemble the necessary suspension and steering components to gain access to the ball joint for removal. 3.1.2 Rotate the hydraulic unit anticlockwise within the press frame until the bottom of the unit is level with the underside of the top bar.