User Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY INSTRUCTIONS



WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.

 WARNING!Disconnect from air supply before changing drill bits, or servicing ,or performing any maintenance.

 Maintain the drill in good condition (use an authorised service agent).



Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty

 Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.

 Before each use check condition of drill bit. Sharpen if necessary. If worn or damaged replace immediately.

 Ensure the speed rating (rpm) of the drill bit is the same as, or greater than, the speed rating of the drill.

 Ensure there are no flammable or combustible materials near the work area.

 Evaluate your working area before using the drill. Ceilings, floors and enclosures may contain hidden electrical wiring, water

pipes or gas pipes.

 WARNING! Always wear approved eye (and/or face) and hand protection when operating the drill.

 Use face, dust, or respiratory protection in accordance with COSHH regulations.

 Depending on the task, the drilling noise level may exceed 84dB in which case wear safety ear defenders.

 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.

 Wear appropriate protective clothing and keep hands and body clear of working parts.

 Maintain correct balance and footing. DO NOT over reach, ensure the floor is not slippery, wear non-slip shoes.

 Keep children and unauthorised persons away from the working area.

 Check moving parts alignment on a regular basis.

 Ensure workpiece is secure before operating the drill. Never hold a workpiece by hand.

 Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.

 Avoid unintentional starting.

 Remove chuck key before starting the drill.

 WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi



Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure all connections are secure.

 Prolonged exposure to vibration from this drill poses a health risk. It is the owner’s responsibility to correctly assess the

potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.

 DO NOT use the drill for a task it is not designed to perform.

 DO NOT operate drill if any parts are damaged or missing as this may cause failure and/or personal injury.

 WARNING! DO NOT drill any materials containing asbestos.

 DO NOT carry the drill by the hose, or yank the hose from the air supply.

 DO NOT force, or apply heavy pressure to the drill; let the tool do the work.

 DO NOT place air line attachments close to your face and do not point at other people or animals.

 DO NOT operate drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 DO NOT use drill where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or

cleaning rags etc.

 DO NOT carry the drill with your finger on the trigger.

 DO NOT direct air from the air line at yourself or others.

 When not in use disconnect from air supply and store in a safe, dry, childproof location.

INSTRUCTIONS FOR:

10mm REVERSIBLE AIR DRILL

MODEL No: SA24.V2

Original Language Version

SA24.V2 Issue: 3 -

12/11/13

2. INTRODUCTION & SPECIFICATION

Free Speed . . . . . . . . . . . . . . . . . . . 1800rpm

Operating Pressure ................90psi

Air Consumption ..................4cfm

Air Inlet ...................... 1/4”BSP

Weight ..........................1.4kg

Chuck Size ......................10mm

Polished alumimium housing with textured grip handle and planetary gear drive assembly. Features reversible

action making this tool suitable for driving fixings. Fitted with 10mm drill chuck supplied with chuck key, built in

muffler. Suitable for general workshop use.

Noise Power ................102.55dB(A)

Noise Pressure...............91.55dB(A)

Vibration ......................2.06m/s²

Vibration Uncertainty ..........0.4236m/s²

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS FOR: 10mm REVERSIBLE AIR DRILL MODEL No: SA24.V2 Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
PAGE 2
3. 3.1.  3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5. 3.1.6. 3.2. PREPARING DRILL FOR USE Air Supply WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the drill. Too high an air pressure and unclean air will cause excessive wear, and may be dangerous, causing damage and/or personal injury. Ensure the drill air valve (or trigger) is not depressed before connecting to the air supply.
PAGE 3
4.3.2. 4.3.3. 4.3.4. 4.3.5. 4.3.6. 4.3.7. 4.3.8.  4.3.9 5. Ensure the drill is turning in the forward direction by checking that the lever adjacent to the trigger is next to the forward symbol (F). If not, push the lever over to the forward position. Hold tool firmly and place the bit tip to the point to be drilled. Depress the trigger to start drill. Move the drill bit into the work piece applying only enough pressure to keep the bit cutting. DO NOT force or apply side pressure to elongate the hole.
PAGE 4
WARNING! – Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): 2.06 m/s² Uncertainty value(k): 0.4236 m/s² Please note that the application of the tool to a sole specialist task may produce a different average vibration emission.