User Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY INSTRUCTIONS

 WARNING! Ensure Health & Safety, local authority and general workshop practice regulations

are adhered to when using this equipment.

 WARNING! Disconnect from air supply before changing accessories or servicing.

 Maintain the tool in good condition and replace any damaged or worn parts. Use genuine parts

only. Unauthorised parts may be dangerous and will invalidate the warranty.

 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.

 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each

use and ensure that all connections are secure.

 Wear approved safety eye/face shield, ear defenders and hand protection.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

 Keep children and non essential persons away from the working area.

 DO NOT use the tool for a task it is not designed to perform.

 WARNING! DO NOT use the tool if damaged or thought to be faulty. Contact a Sealey service

agent.

 DO NOT use tool unless you have been instructed in its use by a qualified person.

 DO NOT carry the tool by the air hose, or yank the hose from the air supply.

 DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating

medication.

 DO NOT carry tool with your hand on the power trigger, this will avoid unintentional starting.

 DO NOT direct air from the air hose at yourself or others.

 When not in use disconnect from the air supply and store in a safe, dry, childproof location.

2. INTRODUCTION & SPECIFICATION

Maximum cutting capacity:..... 1.2mm(Steel)

Air consumption:.................... 4cfm

Operating pressure: .................90psi

Air inlet size:.................... 1/4”BSP

Allen key (supplied):.................4mm

Weight: ..........................1.22kg

Pressure noise level: ............87.8dB(A)

Power noise level ...............98.8dB(A)

Measured vibration emission value ...4.0m/s²

Uncertainty value ................0.13m/s²

Pistol grip design for increased control and manoeuvrability. Finger tipped control and polished

aluminium housing with alloy head. Suitable for cutting straight lines in sheet metal up to 1.2mm

thickness. Blades are consumable items and are not covered by warranty.

Original Language Version

SA53 Issue: 1 - 10/05/13

INSTRUCTIONS FOR:

AIR SHEARS PISTOL TYPE

MODEL No: SA56

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS FOR: AIR SHEARS PISTOL TYPE MODEL No: SA56 Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
PAGE 2
3. PREPARING SHEARS FOR USE 3.1. 3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5. 3.1.6. 3.1.7. 3.2. Air Supply Recommended hook-up procedure is shown in fig 1. Ensure tool valve (or trigger) is in the "off" position before connecting to the air supply. You will require an air pressure of 90psi, and an air flow according to specification.  WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the tool.
PAGE 3
5.3. If the air line does not have a lubricator, lubricate the tool daily with a few drops of Sealey air tool oil dripped into the air inlet. 5.4. Clean the tool after use with a dry cloth. 5.5. Loss of power or erratic action may be due to the following: a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connector. To remedy, check the air supply and follow the instructions in section 3.
PAGE 4
WARNING! – Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not adequately managed. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. This tool has been tested in accordance with: EN ISO 28927-7:2009 & BS EN ISO 15744:2008.